Topic: [WTS] HDMI dummy plug, 4K, EDID emulator monitor, USB WatchDog Timer - page 2. (Read 2397 times)
April 13, 2017, 04:10:10 AM
Emulators in Stock!!!
April 10, 2017, 12:39:43 PM
Yes, now the case is under construction
April 10, 2017, 12:36:52 PM
Very nice -- Will you have any models in the future that actually have some sort of plastic enclosure or will the all be heat shrink only?
April 10, 2017, 12:26:23 PM
Emulator Monitor
Emulates a monitor connected to the graphics card.
Remote control programs such as TeamVewer, Radmin, VNC and others without a monitor present operating only in screen resolution 640x480.
This emulator is designed to simulate the presence of a monitor output video card. It allows you to simulate the screen resolution with a maximum resolution of 4k (3840x2160).
Attention!!!
Resolution 4k (3840x2160) available only with HDMI 1.4, only newest GPUs
Default resolution Full HD (1920x1080)
Also it allows you to run a system that will not start without a monitor!!!
* Plug and Play.
* System Windows/Linux/Mac
* Compatible with any graphics card that has an HDMI output.
* Emulates 8 channel audio up to 192 kHz.
Screen:
Prices for: Ebay
The cost of 1 piece is 7.99 $
The cost of 5 piece is 34.95 $ (LOT 5 PCS)
Special prices for BitcoinTalk - Without Ebay:
1 piece is – 6.99 $ + Post of Russia with tracking 3.5 $
10 piece is – 60 $ + Post of Russia with tracking 6 $
50 piece is – 266 $ + Post of Russia with tracking 11 $
USB WatchDog Timer
WatchDog Prime
USB WatchDog Timer (the Device) is designed to restart and shutdown/turn on the PC in case of hanging or overheating of its individual nodes (CPU and/or GPU). The device is a compact solution that monitors the status of a PC via USB interface. In the case of an unresponsive computer program (Device GPU) will cease to send a signal that will trigger the alarm system reboot or shutdown (or both of them, depending on the setting. Also, the timer will give a reset signal in the case of GPU failure, CPU overheating and/or graphics cards or their small load. In addition, the device provides a system for updating the firmware to fix errors and expand the functionality.
- WatchDog Prime is defined in the system as a full-fledged HID device without virtualization of the COM port
- WatchDog Prime software has an intuitive interface
- Built-in "Power" and "Reset" buttons
- Duplicating contacts "Power" and "Reset" for connecting external buttons
- WatchDog Prime version "USB-PBD10" has reverse polarity protection
- The version of the LITE software is only from the hang of the system (control of Reset and Power)
- Variants of execution: USB-A or USB PBD-10
Characteristics:
- Control Reset and Power ON/OFF - Restart or Shutdown when the system hangs.
- CPU and GPU temperature control - Reboot or Shutdown when the permissible values are exceeded.
- Control of all installed GPUs - Reboot or Disconnect if the GPU fails. (crash video card - remote access is not possible, and the system does not hang)
- Resetting the PC in case of low average GPU load (hang of the program of the miner)
- Connection Test Option (PING) - If the resource is available, but calculations do not go - a problem in the PC, and a reboot is required
- Automatically turn on the PC when power is on
- Control CPU and GPU fans
- Permanent reboot of the computer in case of not loading into the system and detection of software
Downloads:
Software: v.1.53.1 Firmware: v.1.52
Special prices for BitcoinTalk:
1 piece is – 26 $ + Post of Russia with tracking 3.5 $
10 piece is – 120 $ + Post of Russia with tracking 10 $
50 piece is – 1000 $ + Post of Russia with tracking 22 $
Location: Russian Federation
Sending Worldwide:
Post of Russia with tracking - 3.5 $
Fast shipping EMS of Russia with tracking - 40 $
Order and Payment only via e-mail: [email protected]
Payment:
Paypal
Bitcoin BTC
Ethereum [ETH]
My shop: Ebay
Jump to: