Topic: [WTS] Heatsinks for Bitfury Boards or any other Mining device! (Read 3005 times)
all sold- --> closed
November 06, 2013, 10:06:08 AM
Well let me know if there are any left.
November 06, 2013, 08:12:15 AM
I need about 300. Are these still for sale?
I sold a big lot today, have to check how much are left , as I will also need some for myself.
cheers
November 06, 2013, 08:01:36 AM
I need about 300. Are these still for sale?
November 05, 2013, 04:51:31 PM
October 22, 2013, 03:29:59 PM
still available
October 13, 2013, 07:55:35 AM
Price reduction!
I will now offer every package including 20 Heatsinks instead of 16 for 0,1BTC
So also your power regulator can get cooled accordingly and you OC potential and life time will increase
Foofighter
I will now offer every package including 20 Heatsinks instead of 16 for 0,1BTC
So also your power regulator can get cooled accordingly and you OC potential and life time will increase
Foofighter
October 08, 2013, 01:38:03 AM
its totally fine to use only the 2 middle screws, in my opinion.
The sink plates I have are not big enough to use all 6 holes.
The sink plates I have are not big enough to use all 6 holes.
October 07, 2013, 03:34:43 PM
Are ther any heatsinks that use holes on bf board for tight fit?
see 2 posts above?
Yea, but it uses only two middel screws, isn't it?
October 07, 2013, 03:29:47 PM
Are ther any heatsinks that use holes on bf board for tight fit?
see 2 posts above?
October 07, 2013, 03:12:26 PM
Are ther any heatsinks that use holes on bf board for tight fit?
October 07, 2013, 02:55:39 PM
still available
September 28, 2013, 01:40:43 PM
Hey guys,
if there is interest I could also offer a few of those full heatsinks:
they are custom reworked by myself and I have only a handfull of those at hand now for personal useage mostly.
Iam also not sure if the fit in a fully populated Rack as the have a height of 15mm, I would probably only use them if you have only a handful of cards and always a free slot behind a card with this sink.
Pricing would be 0,12 for each piece excluding shipping
cheers
Foofighter
if there is interest I could also offer a few of those full heatsinks:
they are custom reworked by myself and I have only a handfull of those at hand now for personal useage mostly.
Iam also not sure if the fit in a fully populated Rack as the have a height of 15mm, I would probably only use them if you have only a handful of cards and always a free slot behind a card with this sink.
Pricing would be 0,12 for each piece excluding shipping
cheers
Foofighter
September 23, 2013, 03:54:44 PM
First few hundreds are sold.
See here a picture of 1 of my hashing cards:
See here a picture of 1 of my hashing cards:
September 22, 2013, 03:19:03 AM
you are right, the back side is prefered but from temp measurements there isnt so much difference between both sides in temp.
I ordered new heatsinks because many people asked for it, should have them in hand in 1-2 weeks.
So Iam open for new orders here.
cheers
Foofighter
I ordered new heatsinks because many people asked for it, should have them in hand in 1-2 weeks.
So Iam open for new orders here.
cheers
Foofighter
September 07, 2013, 03:33:54 PM
Another Deal done here,
about 350 pieces are left to sell now guys.
BR
Foofighter
EDIT:
Just saw that also ASICME, a chinese avalon clone manufacturer uses similar sinks for testing purposes
http://asicme.com/en/news
about 350 pieces are left to sell now guys.
BR
Foofighter
EDIT:
Just saw that also ASICME, a chinese avalon clone manufacturer uses similar sinks for testing purposes
http://asicme.com/en/news
Why would they add heat sinks to the TOP of an Avalon board?
The packaging of the Avalon chip has the chip die bonded to the bottom side of the carrier, and rejects heat out the bottom of the chip.
Which is why they have those large thermal via's on the bottom of the board. There is a air gap between the die and the top of the chip carrier.
Adding heat sinks to the top of an Avalon doesn't do anything. It just costs money.
September 02, 2013, 10:48:54 AM
Ah ok, hope you had fun! 
September 02, 2013, 03:56:57 AM
So Foofighter did you read my post? Have you tried them with an adjacent board and not just standalone?
Hi,
not tested so far, had no time, just came back from vacation.
BR
So Foofighter did you read my post? Have you tried them with an adjacent board and not just standalone?
My face when you get this stuff cheaper than I could, even though I live a relatively short drive from their global headquarters...
Jump to: