I have problem in masternode set. I was follow all the rest of guide and tried did many times but still has error: "Not capable masternode: Masternode not in masternode list".
Please help me to fix its.
Thank you
Topic: ✅|ANN| 🌍DESIRE |NeoScrypt| |🔨MasterNodes🔨| - COIN OF YOUR DREAMS! - page 128. (Read 167492 times)
November 01, 2017, 05:36:35 AM
November 01, 2017, 05:32:28 AM
The GPU MINING Is Good For Me 
November 01, 2017, 05:27:31 AM
I have setup MN on a VPS and trying to configure my masternode.config at my local controller wallet.
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
the command "masternode outputs" will give you what you need
I get this when i run masternode outputs
{
"4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7": "1"
}
so what should i substitute these two with? COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7 1
Thank you! It is preenabled now!
Is it possible to create multiple nodes and enable them via single controller wallet?
For Desire MN, I don't think it's possible to have more than 1 MN per public IP.
Right, i tried for 3 nodes and one started and other two went missing, for the same public IP. I will try if any other method works. Thank you!
Hello. I cannot configure Masternode on VPS server using ipv6 address, my local wallet say"incorrect ip", but when i use ipv4 - it's all right.
Also in local wallet in list of masternodes i see only ipv4 addresses
Desire wallet cannot use ipv6 ?
November 01, 2017, 04:09:41 AM
Should be listed on Saturday I believe. Has CMC been applied for so people can research DSR?
November 01, 2017, 03:58:02 AM
I think Yobit fees has been paid.. within this week desire will be there.
November 01, 2017, 03:42:33 AM
when you plan to exit the coins in yobit?
Yobit list fee is 1000$ if I remenber it right. November 01, 2017, 03:41:35 AM
New bounty!+ 5 DSR for you
1. Write in the comments to this tweet that you need to add Desire.
2. Make a screenshot and send it along with the address for bounties to me in the PM.
2. Make a screenshot and send it along with the address for bounties to me in the PM.
Thanks for the bounty
November 01, 2017, 02:57:20 AM
I will try to participate in bounties, i will pm you soon, thank you.
November 01, 2017, 02:49:01 AM
when you plan to exit the coins in yobit?
November 01, 2017, 01:47:53 AM
I have setup MN on a VPS and trying to configure my masternode.config at my local controller wallet.
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
the command "masternode outputs" will give you what you need
I get this when i run masternode outputs
{
"4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7": "1"
}
so what should i substitute these two with? COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7 1
Thank you! It is preenabled now!
Is it possible to create multiple nodes and enable them via single controller wallet?
For Desire MN, I don't think it's possible to have more than 1 MN per public IP.
Right, i tried for 3 nodes and one started and other two went missing, for the same public IP. I will try if any other method works. Thank you!
November 01, 2017, 01:46:55 AM
Hello there,
I try to setup a vps masternode, i used the setup of the linux wallet at the first post of this thread :
https://masternodes.github.io/vps/docs/masternode_vps.html
when i try to startup the wallet using: /usr/local/bin/restart_masternodes.sh
I get error message: " Job for desire_n1.service failed because the control
process exited with error code. See "systemctl status
desire_n1.service" and "journalctl -xe" for details."
so could you help me guys please
or is there any other tutorial to setup vps desire wallet other than that one on the first post of this thread
I try to setup a vps masternode, i used the setup of the linux wallet at the first post of this thread :
https://masternodes.github.io/vps/docs/masternode_vps.html
when i try to startup the wallet using: /usr/local/bin/restart_masternodes.sh
I get error message: " Job for desire_n1.service failed because the control
process exited with error code. See "systemctl status
desire_n1.service" and "journalctl -xe" for details."
so could you help me guys please
or is there any other tutorial to setup vps desire wallet other than that one on the first post of this thread
November 01, 2017, 01:26:57 AM
I have setup MN on a VPS and trying to configure my masternode.config at my local controller wallet.
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
the command "masternode outputs" will give you what you need
I get this when i run masternode outputs
{
"4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7": "1"
}
so what should i substitute these two with? COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7 1
Thank you! It is preenabled now!
Is it possible to create multiple nodes and enable them via single controller wallet?
For Desire MN, I don't think it's possible to have more than 1 MN per public IP.
Right, i tried for 3 nodes and one started and other two went missing, for the same public IP. I will try if any other method works. Thank you!
November 01, 2017, 01:23:43 AM
I have setup MN on a VPS and trying to configure my masternode.config at my local controller wallet.
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
the command "masternode outputs" will give you what you need
I get this when i run masternode outputs
{
"4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7": "1"
}
so what should i substitute these two with? COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7 1
Thank you! It is preenabled now!
Is it possible to create multiple nodes and enable them via single controller wallet?
For Desire MN, I don't think it's possible to have more than 1 MN per public IP.
November 01, 2017, 01:18:43 AM
I have setup MN on a VPS and trying to configure my masternode.config at my local controller wallet.
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
the command "masternode outputs" will give you what you need
I get this when i run masternode outputs
{
"4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7": "1"
}
so what should i substitute these two with? COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7 1
Thank you! It is preenabled now!
Is it possible to create multiple nodes and enable them via single controller wallet?
November 01, 2017, 01:13:24 AM
Hi just started following this project, will you be applying for listing on CMC anytime soon to coincide with the Yobit listing now that they have added Coinsmarket as one of their tracked exchanges?
November 01, 2017, 12:44:58 AM
My masternod appears as Enabled in the ALl masternode tab the time "last seen " is correkt
But i have non received a payment since about 7 or more hours Not sure if its normal or not
masternode debug in debug mode
says tat Masternode startet succesfull
Please send email to mnrank.com to correkt the price per Coin it appears as 5,5 wich is not
But i have non received a payment since about 7 or more hours Not sure if its normal or not
masternode debug in debug mode
says tat Masternode startet succesfull
Please send email to mnrank.com to correkt the price per Coin it appears as 5,5 wich is not
November 01, 2017, 12:36:35 AM
It seems many people complaint about masternode not working . Does masternode working fine for anyone ? if, can you tell me which cloud service are you using to host mn ?
November 01, 2017, 12:18:16 AM
I have setup MN on a VPS and trying to configure my masternode.config at my local controller wallet.
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
the command "masternode outputs" will give you what you need
I get this when i run masternode outputs
{
"4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7": "1"
}
so what should i substitute these two with? COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7 1
November 01, 2017, 12:17:41 AM
I have setup MN on a VPS and trying to configure my masternode.config at my local controller wallet.
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
the command "masternode outputs" will give you what you need
I get this when i run masternode outputs
{
"4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7": "1"
}
so what should i substitute these two with? COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
yes just take this portion
4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7 1
November 01, 2017, 12:10:50 AM
I have setup MN on a VPS and trying to configure my masternode.config at my local controller wallet.
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
In the below format, what does
COLLATERAL_TX_FOR_desireMN1
&
OUTPUT_NO_FOR_desireMN1
means?
Format:
desireMN1 IP:9919 MASTERNODE_PRIVKEY_FOR_desireMN1 COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
the command "masternode outputs" will give you what you need
I get this when i run masternode outputs
{
"4MASKEDXXXXXXXXXXXXXXXXXXXXXXXMASKEDXXXXXXXXXXXXX7": "1"
}
so what should i substitute these two with? COLLATERAL_TX_FOR_desireMN1 OUTPUT_NO_FOR_desireMN1
Jump to: