Topic: [ANN] Spondoolies-Tech - carrier grade, data center ready mining rigs - page 190. (Read 1260290 times)
January 16, 2015, 01:44:42 PM
aclass and tupsu Thanks, that fixed it.
January 16, 2015, 01:29:53 PM
Did anybody tried to run SP30 more energy efficiently? If yes, care to share the settings and what the energy consumption/hashing speed will result?
I have my units in hosting, so cannot play with settings as easily as with SP20 at home.
I have my units in hosting, so cannot play with settings as easily as with SP20 at home.
A few that I tried, the green was the optimal until the recent price drop, now they are all offline, UK electric rates kill any chance of profit
January 16, 2015, 01:21:20 PM
Did anybody tried to run SP30 more energy efficiently? If yes, care to share the settings and what the energy consumption/hashing speed will result?
I have my units in hosting, so cannot play with settings as easily as with SP20 at home.
I have my units in hosting, so cannot play with settings as easily as with SP20 at home.
I tried a quick test and I used start voltage .60 and set the max PSUs to 750W and it worked just fine. Can't remember stats because as I said it was just a quick test. Maybe I will have more spare time in week-end.
I will go over requests next week. I recomend using voltage only (set start and max to same values or give 5 millivolt between them) till you get the performance you want. If you set too low system will not start. Keep the psu wattage as is since it will never be reached if you set max volts low enough.
Whats new in 2.6.1 zvi?
January 16, 2015, 01:18:19 PM
Did anybody tried to run SP30 more energy efficiently? If yes, care to share the settings and what the energy consumption/hashing speed will result?
I have my units in hosting, so cannot play with settings as easily as with SP20 at home.
I have my units in hosting, so cannot play with settings as easily as with SP20 at home.
I tried a quick test and I used start voltage .60 and set the max PSUs to 750W and it worked just fine. Can't remember stats because as I said it was just a quick test. Maybe I will have more spare time in week-end.
I will go over requests next week. I recomend using voltage only (set start and max to same values or give 5 millivolt between them) till you get the performance you want. If you set too low system will not start. Keep the psu wattage as is since it will never be reached if you set max volts low enough.
January 16, 2015, 01:12:52 PM
Did anybody tried to run SP30 more energy efficiently? If yes, care to share the settings and what the energy consumption/hashing speed will result?
I have my units in hosting, so cannot play with settings as easily as with SP20 at home.
I have my units in hosting, so cannot play with settings as easily as with SP20 at home.
I tried a quick test and I used start voltage .60 and set the max PSUs to 750W and it worked just fine. Can't remember stats because as I said it was just a quick test. Maybe I will have more spare time in week-end.
January 16, 2015, 12:58:17 PM
Did anybody tried to run SP30 more energy efficiently? If yes, care to share the settings and what the energy consumption/hashing speed will result?
I have my units in hosting, so cannot play with settings as easily as with SP20 at home.
I have my units in hosting, so cannot play with settings as easily as with SP20 at home.
January 16, 2015, 12:08:26 PM
Hi,
Feature for firmware:
Make easy to change hostname
Feature for firmware:
Make easy to change hostname
+1
Would you please share, "the difficult way" of changing the hostname of the SP3x. I followed the steps in the guide here, but it did not help: http://www.cyberciti.biz/faq/linux-change-hostname/
I am still with the old hostname:(
Is anyone else has found a way of changing it?
Thank you.
January 16, 2015, 12:06:05 PM
luci is from your Ants. Clear cache or change the IP of the miner 
Quick question for those that have had SPT Miners for a while. I have one SP20 that when you try to go to home page you get a 404 page not found. The url that displays is the Miner's IpAddress/cgi-bin/luci . The miner works fine otherwise and I can access the other pages setup etc just by putting the url for that page in directly. I have tried updating firmware and that didn't fix it. Has anyone had this before and is there an easy fix or am I looking at a recover or flash? Thanks
January 16, 2015, 11:51:25 AM
Quick question for those that have had SPT Miners for a while. I have one SP20 that when you try to go to home page you get a 404 page not found. The url that displays is the Miner's IpAddress/cgi-bin/luci . The miner works fine otherwise and I can access the other pages setup etc just by putting the url for that page in directly. I have tried updating firmware and that didn't fix it. Has anyone had this before and is there an easy fix or am I looking at a recover or flash? Thanks
Clear the browser cache
January 16, 2015, 10:47:57 AM
Quick question for those that have had SPT Miners for a while. I have one SP20 that when you try to go to home page you get a 404 page not found. The url that displays is the Miner's IpAddress/cgi-bin/luci . The miner works fine otherwise and I can access the other pages setup etc just by putting the url for that page in directly. I have tried updating firmware and that didn't fix it. Has anyone had this before and is there an easy fix or am I looking at a recover or flash? Thanks
January 16, 2015, 09:11:43 AM
Let us know what you want to see in Spondoolies-Tech's firmware… We are open to suggestions! What do you want to see implemented in our next firmware releases? We want to hear from you, although we cannot make any promises to implement any suggestion, we will try out best to make it work. Post suggestions here in the thread…
I would like to see target temperature support whereby the firmware constantly adjusts fanspeed to the lowest possible RPM that will maintain the device just below a target temperature. Where cgminer drivers have had the ability to adjust fanspeed continuously, I have coded up this feature into them but the fanspeed control is not within cgminer on sp gear.Temperature range along with scheduling would be nice; Support other pool options in addition to Failover;
Unreasonable wishlist -- Allow me to set my efficiency and have the SP20 auto adjust watts/volts/temp/fan/etc to obtain
January 16, 2015, 05:31:05 AM
Let us know what you want to see in Spondoolies-Tech's firmware… We are open to suggestions! What do you want to see implemented in our next firmware releases? We want to hear from you, although we cannot make any promises to implement any suggestion, we will try out best to make it work. Post suggestions here in the thread…
I would like to see target temperature support whereby the firmware constantly adjusts fanspeed to the lowest possible RPM that will maintain the device just below a target temperature. Where cgminer drivers have had the ability to adjust fanspeed continuously, I have coded up this feature into them but the fanspeed control is not within cgminer on sp gear. January 16, 2015, 04:09:54 AM
I have a customer with a bad SP31 prob psu + cables broken (melted) down.... Where can i get support for this...
Directly from Spondoolies, email [email protected]
January 16, 2015, 04:07:43 AM
I have a customer with a bad SP31 prob psu + cables broken (melted) down.... Where can i get support for this...
January 16, 2015, 03:26:33 AM
+1 - some Places have almost free power at night. So running it overclocked during the night, and underclock/run normal during the day.
That usually happens with nuclear power plants providing base-load. In Ontario (Canada) the price even went negative for a time. (In Alberta the price is only allowed to go to 0 by fiat. (No nuclear power plants though).)
January 16, 2015, 03:17:29 AM
One more feature request:
Settings profiles with scheduling Power is less expensive during the night here so I can get more GH at the same price.
This will also help miners located in office areas where there is nobody at night.
Settings profiles with scheduling
Power is less expensive during the night here so I can get more GH at the same price.This will also help miners located in office areas where there is nobody at night.
+1 - some Places have almost free power at night. So running it overclocked during the night, and underclock/run normal during the day.
January 16, 2015, 03:13:15 AM
One more feature request:
Settings profiles with scheduling Power is less expensive during the night here so I can get more GH at the same price.
This will also help miners located in office areas where there is nobody at night.
Settings profiles with scheduling
Power is less expensive during the night here so I can get more GH at the same price.This will also help miners located in office areas where there is nobody at night.
January 16, 2015, 01:46:31 AM
Hi,
Feature for firmware:
Make easy to change hostname
Feature for firmware:
Make easy to change hostname
January 16, 2015, 12:51:57 AM
I just wanted to thank you for paying attention to mining conditions and lowering price. Very nice to see a company following and listening to miners.
January 15, 2015, 05:37:18 PM
It happens if the miner can't reach the pool.ntp.org server to set its time.
Thanks Biffa didn't know that.
... manually set the time from the GUI
Sounds good if the pool.ntp.org server isn't playing ball.
Jump to: