[ANN] Spondoolies-Tech - carrier grade, data center ready mining rigs - page 239.

John (John K.)

legendary

Activity: 1288

Merit: 1227

Away on an extended break

Quote from: Helnick on December 15, 2014, 10:59:05 PM

Quote from: John (John K.) on December 15, 2014, 10:53:37 PM

Quote from: Helnick on December 15, 2014, 10:50:17 PM

Quote from: John (John K.) on December 15, 2014, 10:46:17 PM

Quote from: Helnick on December 15, 2014, 10:41:58 PM

My Sp 20 is disconnecting/ stopping mining for no reason. I have 1300PSU platinum going and it keeps knocking itself offline. The fan is still running so the only way I can tell is when I log into it, which I can't do at that point. I log into my stats page on eligius and I can see I am zero hashing. If I reboot PSU then it comes back on. Seems to be happening between every 4 and 24 hours. Is anyone else having this issue?
I have reset to factory and now trying to run. we will see how this goes.

Exactly what I was having for a few times today. Is it running hot? I moved it to somewhere cold, and it hasn't crashed yet. *touches wood*

In garage. 30 degrees in there. Its not hot to the touch at all. psu wires not hot. I just reset to factory. maybe this will do it. time will tell.

What is the temperature shown in the Asic stat page? i had it in somewhere around 27*C, and it crashed afterwards. It's at somewhere 5*C now, still going with the stats in my last post above.

http://imageshack.com/a/img537/5430/XQJ9v8.png

here's what I have. Why are some in yellow?

The max temps are 125*C for each of them. Once it hits 120*C I think they start to throttle themselves. According to what I've read, try keeping them at < 115*C for them to run more stably. I'm suspecting that the high temps in there might've caused the controller board to freeze somehow.

Helnick

newbie

Activity: 26

Merit: 0

Quote from: John (John K.) on December 15, 2014, 10:53:37 PM

Quote from: Helnick on December 15, 2014, 10:50:17 PM

Quote from: John (John K.) on December 15, 2014, 10:46:17 PM

Quote from: Helnick on December 15, 2014, 10:41:58 PM

My Sp 20 is disconnecting/ stopping mining for no reason. I have 1300PSU platinum going and it keeps knocking itself offline. The fan is still running so the only way I can tell is when I log into it, which I can't do at that point. I log into my stats page on eligius and I can see I am zero hashing. If I reboot PSU then it comes back on. Seems to be happening between every 4 and 24 hours. Is anyone else having this issue?
I have reset to factory and now trying to run. we will see how this goes.

Exactly what I was having for a few times today. Is it running hot? I moved it to somewhere cold, and it hasn't crashed yet. *touches wood*

In garage. 30 degrees in there. Its not hot to the touch at all. psu wires not hot. I just reset to factory. maybe this will do it. time will tell.

What is the temperature shown in the Asic stat page? i had it in somewhere around 27*C, and it crashed afterwards. It's at somewhere 5*C now, still going with the stats in my last post above.

http://imageshack.com/a/img537/5430/XQJ9v8.png
http://imageshack.com/a/img537/5430/XQJ9v8.png

here's what I have. Why are some in yellow?

John (John K.)

legendary

Activity: 1288

Merit: 1227

Away on an extended break

Quote from: Helnick on December 15, 2014, 10:50:17 PM

Quote from: John (John K.) on December 15, 2014, 10:46:17 PM

Quote from: Helnick on December 15, 2014, 10:41:58 PM

My Sp 20 is disconnecting/ stopping mining for no reason. I have 1300PSU platinum going and it keeps knocking itself offline. The fan is still running so the only way I can tell is when I log into it, which I can't do at that point. I log into my stats page on eligius and I can see I am zero hashing. If I reboot PSU then it comes back on. Seems to be happening between every 4 and 24 hours. Is anyone else having this issue?
I have reset to factory and now trying to run. we will see how this goes.

Exactly what I was having for a few times today. Is it running hot? I moved it to somewhere cold, and it hasn't crashed yet. *touches wood*

In garage. 30 degrees in there. Its not hot to the touch at all. psu wires not hot. I just reset to factory. maybe this will do it. time will tell.

What is the temperature shown in the Asic stat page? i had it in somewhere around 27*C, and it crashed afterwards. It's at somewhere 5*C now, still going with the stats in my last post above.

Helnick

newbie

Activity: 26

Merit: 0

Quote from: John (John K.) on December 15, 2014, 10:46:17 PM

Quote from: Helnick on December 15, 2014, 10:41:58 PM

My Sp 20 is disconnecting/ stopping mining for no reason. I have 1300PSU platinum going and it keeps knocking itself offline. The fan is still running so the only way I can tell is when I log into it, which I can't do at that point. I log into my stats page on eligius and I can see I am zero hashing. If I reboot PSU then it comes back on. Seems to be happening between every 4 and 24 hours. Is anyone else having this issue?
I have reset to factory and now trying to run. we will see how this goes.

Exactly what I was having for a few times today. Is it running hot? I moved it to somewhere cold, and it hasn't crashed yet. *touches wood*

In garage. 30 degrees in there. Its not hot to the touch at all. psu wires not hot. I just reset to factory. maybe this will do it. time will tell.

John (John K.)

legendary

Activity: 1288

Merit: 1227

Away on an extended break

Quote from: Helnick on December 15, 2014, 10:41:58 PM

My Sp 20 is disconnecting/ stopping mining for no reason. I have 1300PSU platinum going and it keeps knocking itself offline. The fan is still running so the only way I can tell is when I log into it, which I can't do at that point. I log into my stats page on eligius and I can see I am zero hashing. If I reboot PSU then it comes back on. Seems to be happening between every 4 and 24 hours. Is anyone else having this issue?
I have reset to factory and now trying to run. we will see how this goes.

Exactly what I was having for a few times today. Is it running hot? I moved it to somewhere cold, and it hasn't crashed yet. *touches wood*

Helnick

newbie

Activity: 26

Merit: 0

My Sp 20 is disconnecting/ stopping mining for no reason. I have 1300PSU platinum going and it keeps knocking itself offline. The fan is still running so the only way I can tell is when I log into it, which I can't do at that point. I log into my stats page on eligius and I can see I am zero hashing. If I reboot PSU then it comes back on. Seems to be happening between every 4 and 24 hours. Is anyone else having this issue?
I have reset to factory and now trying to run. we will see how this goes.

-ck

legendary

Activity: 4088

Merit: 1631

Ruu \o/

I've experimented with hacking the sp20 to fan speeds below those supported. When the device isn't overclocked (0.66v max) it seems to run fine at 20% fanspeed without overheating despite ambient temps today being in the high 20s. Noise is always an issue and this helps a little.

John (John K.)

legendary

Activity: 1288

Merit: 1227

Away on an extended break

Running stable around 1.6TH/s after placing this at a cool location (window-sill). I'm just wondering why one of the modules is running consistently at 120*C, lol. That particular module is running at a lower voltage then the others, too.

Code:

Uptime:2882 | FPGA ver:100
-----BOARD-0-----
PSU[UNKNOWN]: 0->286w[286 285 285] (->286w[286 285 285]) (lim=288) 0c cooling:0/0x0
-----BOARD-1-----
PSU[UNKNOWN]: 0->236w[236 236 236] (->236w[236 236 236]) (lim=240) 0c cooling:0/0x0
-----BOARD-2-----
PSU[UNKNOWN]: 0->269w[269 269 269] (->269w[269 269 269]) (lim=288) 0c cooling:0/0x0
-----BOARD-3-----
PSU[UNKNOWN]: 0->235w[235 235 235] (->235w[235 235 235]) (lim=240) 0c cooling:0/0x0
LOOP[0] ON TO:0
0: DC2DC/1/:[vlt1:750 vlt2:754(DCl:794 Tl:794 Ul:759) 116W 154A 60c] ASIC:[ 85c (125c) 1110hz(BL:1110) 214 (E:192) F:0 L:0]
1: DC2DC/1/:[vlt1:750 vlt2:754(DCl:794 Tl:794 Ul:759) 115W 153A 70c] ASIC:[ 85c (125c) 1110hz(BL:1110) 191 (E:193) F:0 L:0]
LOOP[1] ON TO:0
2: DC2DC/1/:[vlt1:697 vlt2:703(DCl:794 Tl:794 Ul:759) 90W 128A 78c] ASIC:[ 85c (125c) 1000hz(BL:1000) 205 (E:193) F:0 L:0]
3: DC2DC/1/:[vlt1:699 vlt2:703(DCl:794 Tl:794 Ul:759) 100W 142A 88c] ASIC:[120c (125c) 1050hz(BL:1050) 184 (E:193) F:0 L:0]
LOOP[2] ON TO:0
4: DC2DC/1/:[vlt1:750 vlt2:754(DCl:754 Tl:794 Ul:759) 116W 154A 48c] ASIC:[ 85c (125c) 1095hz(BL:1095) 189 (E:193) F:0 L:0]
5: DC2DC/1/:[vlt1:753 vlt2:759(DCl:794 Tl:794 Ul:759) 102W 134A 56c] ASIC:[ 85c (125c) 980hz(BL: 980) 189 (E:193) F:0 L:0]
LOOP[3] ON TO:0
6: DC2DC/1/:[vlt1:722 vlt2:727(DCl:794 Tl:794 Ul:759) 98W 135A 65c] ASIC:[ 85c (125c) 1000hz(BL:1000) 189 (E:193) F:0 L:0]
7: DC2DC/1/:[vlt1:722 vlt2:727(DCl:794 Tl:794 Ul:759) 92W 126A 68c] ASIC:[ 85c (125c) 970hz(BL: 970) 183 (E:193) F:0 L:0]

[H:HW:1604Gh,W:831,L:0,A:8,MMtmp:0 TMP:(15)=>=>=>(61,49)]
Pushed 29 jobs , in HW queue 4 jobs (sw:0, hw:0)!
min:34 wins:1544[this/last min:10/19] bist-fail:440, hw-err:0
leading-zeroes:42 idle promils[s/m]:0/1, rate:1328gh/s asic-count:392 (wins:5+5)
Fan:90, conseq:200
AC2DC BAD: 0 0
R/NR: 1570/0
RTF asics: 0
FET: 0:9 1:9
0 restarted 0 reset 0 reset2 0 fake_wins
0 stuck_bist 0 low_power 0 stuck_pll 0 runtime_dsble
0 purge_queue 0 read_timeouts 0 dc2dc_i2c 0 read_tmout2 0 read_crptn
0 purge_queue3 0 bad_idle
0 err_murata
Adapter queues: rsp=3, req=20

wh00per

hero member

Activity: 572

Merit: 500

Quote from: samsonn25 on December 15, 2014, 05:44:26 PM

Quote from: raskul on December 15, 2014, 03:18:21 PM

folks have been asking me about renting out SP20's on rental sites...

please see short guide here:
https://bitcointalksearch.org/topic/m.9849580

I still dont understand why people would rent equipment that costs more to rent than the btc it mines?

Owners who enjoy the hobby and actually have and own the equipment are different.

heh .. because if I need 200TH for 2 hrs today, I don't need to buy the equipment and infrastructure to run it. I just rent 150 x Sp20 to do my job.

Did you ever rent a car? Almost always, renting a car costs more than you pay to own it. Do I make sense?

wh00per

hero member

Activity: 572

Merit: 500

Quote from: John (John K.) on December 15, 2014, 08:02:50 PM

Quick question, does anyone's SP20 crash after 1-2 hours of running? I probably have the values wrong...

anything in the logs around the moment it crashes ? (aka "events" tab on the UI)

wh00per

hero member

Activity: 572

Merit: 500

Quote from: mtnksf on December 15, 2014, 06:18:36 PM

My electricity cost is cheaper at night than daytime. So far I'm runing SP20 with energy efficient settings, but I want to change fan/voltage setting between day and night with cron.

What files contains fan/voltage settings and what command I can start/stop cgminer for SP20?

Thanks in advance.

Try the minergate configuration file /mnt/config/etc/mg_custom_mode
After you modify the settings, try to restart minergate (which controls the unit), not cgminer which deals with the hashes only.

Anyway, if you kill cgminer, the watchdog will restart it .. but if minergate is not restarted, it'll run with the same configuration ..
see here how you kill cgminer >> https://bitcointalk.org/index.php?topic=521520.msg9253830;topicseen#msg9253830

You have a button to restart minergate. What it does .. it triggers "/usr/local/bin/spond-manager " with the "restart" option;
Of course, you can CRON it to restart the unit after you run a script to change some file names there ..

John (John K.)

legendary

Activity: 1288

Merit: 1227

Away on an extended break

Quick question, does anyone's SP20 crash after 1-2 hours of running? I probably have the values wrong...

mtnksf

newbie

Activity: 19

Merit: 0

My electricity cost is cheaper at night than daytime. So far I'm runing SP20 with energy efficient settings, but I want to change fan/voltage setting between day and night with cron.

What files contains fan/voltage settings and what command I can start/stop cgminer for SP20?

Thanks in advance.

raskul

sr. member

Activity: 434

Merit: 250

Quote from: samsonn25 on December 15, 2014, 05:44:26 PM

Quote from: raskul on December 15, 2014, 03:18:21 PM

folks have been asking me about renting out SP20's on rental sites...

please see short guide here:
https://bitcointalksearch.org/topic/m.9849580

I still dont understand why people would rent equipment that costs more to rent than the btc it mines?

Owners who enjoy the hobby and actually have and own the equipment are different.

currently, they are not mining BTC.

however, I do rent miners, but I mine on DGM pools which is a whole different kettle of fish than your standard 0.01257btc/th/day that you will find on other mining methods.

I like to find the smallest pool possible and hash away for as long as it takes to solve the round blocks.
always mined DGM and it's never done me wrong to date.

samsonn25

hero member

Activity: 882

Merit: 1003

Quote from: raskul on December 15, 2014, 03:18:21 PM

folks have been asking me about renting out SP20's on rental sites...

please see short guide here:
https://bitcointalksearch.org/topic/m.9849580

I still dont understand why people would rent equipment that costs more to rent than the btc it mines?

Owners who enjoy the hobby and actually have and own the equipment are different.

Hunger

member

Activity: 85

Merit: 10

Underclocking: running 1x Corsair CX750w

Temp Front / Back T,B
18 °C / 41,38 °C
Fan Speed
40
Start Voltage
0.65 / 0.65 / 0.65 / 0.65
Max Voltage
0.66
Max Watts
175 / 175 / 175 / 175

LOOP[0] ON TO:0
0: DC2DC/1/:[vlt1:656 vlt2:658(DCl:794 Tl:794 Ul:658) 67W 102A 37c] ASIC:[ 85c (125c) 845hz(BL: 845) 2 (E:193) F:0 L:0]
1: DC2DC/1/:[vlt1:654 vlt2:658(DCl:794 Tl:794 Ul:658) 68W 104A 49c] ASIC:[ 85c (125c) 875hz(BL: 875) 6 (E:193) F:0 L:0]
LOOP[1] ON TO:0
2: DC2DC/1/:[vlt1:648 vlt2:653(DCl:794 Tl:794 Ul:658) 67W 102A 53c] ASIC:[ 85c (125c) 855hz(BL: 855) 5 (E:193) F:0 L:0]
3: DC2DC/1/:[vlt1:650 vlt2:653(DCl:794 Tl:794 Ul:658) 69W 106A 56c] ASIC:[ 85c (125c) 875hz(BL: 875) 1 (E:193) F:0 L:0]
LOOP[2] ON TO:0
4: DC2DC/1/:[vlt1:650 vlt2:656(DCl:794 Tl:794 Ul:658) 68W 104A 40c] ASIC:[ 85c (125c) 855hz(BL: 855) 7 (E:193) F:0 L:0]
5: DC2DC/1/:[vlt1:654 vlt2:658(DCl:794 Tl:794 Ul:658) 68W 104A 49c] ASIC:[ 85c (125c) 860hz(BL: 860) 0 (E:193) F:0 L:0]
LOOP[3] ON TO:0
6: DC2DC/1/:[vlt1:654 vlt2:658(DCl:794 Tl:794 Ul:658) 66W 101A 51c] ASIC:[ 85c (125c) 835hz(BL: 835) 4 (E:193) F:0 L:0]
7: DC2DC/1/:[vlt1:652 vlt2:658(DCl:794 Tl:794 Ul:658) 68W 104A 55c] ASIC:[ 85c (125c) 855hz(BL: 855) 7 (E:193) F:0 L:0]

Just want to confirm if this settings are alright? only green numbers on the asic stats

raskul

sr. member

Activity: 434

Merit: 250

folks have been asking me about renting out SP20's on rental sites...

please see short guide here:
https://bitcointalksearch.org/topic/m.9849580

zvisha

hero member

Activity: 560

Merit: 500

Biodom

legendary

Activity: 3892

Merit: 4331

Quote from: raskul on December 15, 2014, 01:29:42 AM

Quote from: vortexz on December 15, 2014, 01:27:34 AM

Quote from: Guy Corem on December 14, 2014, 11:28:28 PM

Quote from: vortexz on December 14, 2014, 04:03:01 PM

Quote from: Guy Corem on December 14, 2014, 02:10:24 PM

Quote from: vortexz on December 14, 2014, 10:29:04 AM

I have 2 SP20s, for one of them I can not acces the settings page anymore,
My router assiged the following ip adresees : 192.168.1.99 and 192.168.1.100
I can access just fine the one ending with 99
But I can not acces the one with 100 anymore saying that the web page is not available when I try accessing it from my browser

Both of them are up and mining, they have the pool settings stored, I just can't access one of them's menu

this are the ip's asigned by the router: http://gyazo.com/1dcfb737298ce594e928aa99131f1dac

Any ideeas? thank you !

Try to access via another laptop/desktop on the same network, browse to http://myminer.io

I did all this, I also assigned another ip, I cleared cache, I tried connecting from another laptop from same network, I even tried from my phone.Nothing seems to work

Please help !

Can anyone from your team give me some support ? maybe connect to me via TeamViewer and help me out ?

Follow the SP20 SD recovery procedure in the technical blog.
If it won't work, contact tech.support@ for diagnostic and RMA if needed.

where can I find this recovery procedure blog ?

http://www.spondoolies-tech.com/blogs/technical-blog/13098521-sp10-sp2x-sp3x-recovery-sd-card-boot-sd-card-creation-instructions

the instructions are for Linux.
can you adapt them for Terminal (Mac OSX), please?
Below are the instructions I found and successfully used for SD card image preparation (for competitors hardware ONLY!!!)
https://bitcointalksearch.org/topic/antminer-s2-discussion-and-support-thread-515448
Is is possible to adapt these procedures to SP3X or SP20?
Thanks

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

Quote from: 727miner on December 15, 2014, 12:13:32 AM

Quote from: -ck on December 14, 2014, 10:55:42 PM

Thanks again to the spondoolies team who have now also donated an SP20 for continued cgminer support!

Man, that's cool! I don't see Bitmain doing that, eh!

I don't think they did that for ck and they should have sent him a s-1 a s-2 a s-3 a s-4 and WTF a c-1

Topic: [ANN] Spondoolies-Tech - carrier grade, data center ready mining rigs - page 239. (Read 1260290 times)