[ANN][POOL] Mining Pool Hub - Multipool. Multialgo, Auto Exchange to any coin. - page 147.

CryptoSidd

newbie

Activity: 8

Merit: 0

Quote from: papampi on December 09, 2017, 06:02:09 AM

I'm getting weird low hash rate when mining lyra2rev2 vert and mona
I have 7x270 Mh/s workers so it should be around 1890 mh/s

I know pool shows hash rate based on accepted shares, but its way lower than my workers hash rate
Its ok when I mine equihash and hash rates are almost same, but on lyra2re2 its not

http://oi65.tinypic.com/2lnwc42.jpg
http://oi65.tinypic.com/2lnwc42.jpg

As you can see it never goes over 1100 while it should reach 1800

Using Alexis ccminer
one of my workers output :

Code:

[2017-12-09 14:16:30] [S/A/T]: 0/456/456, diff: 0.779, 276.77MH/s yes! 
[2017-12-09 14:16:30] [S/A/T]: 0/457/457, diff: 0.760, 276.77MH/s yes! 
[2017-12-09 14:16:34] [S/A/T]: 0/458/458, diff: 10.370, 276.77MH/s yes! 
[2017-12-09 14:16:42] GPU#7:Gigabyte P106-100, 22.96MH/s 
[2017-12-09 14:16:42] GPU#7:Gigabyte P106-100, 0.3MH/W, 0.013MH/Mhz 
[2017-12-09 14:16:42] GPU#7:Gigabyte P106-100, 56C(F:50%) 1792/2999MHz(76W) 
[2017-12-09 14:16:42] [S/A/T]: 0/459/459, diff: 4.908, 276.77MH/s yes! 
[2017-12-09 14:16:46] lyra2v2 block 838574, diff 79706.439 
[2017-12-09 14:16:53] lyra2v2 block 838575, diff 79902.176 
[2017-12-09 14:17:07] [S/A/T]: 0/460/460, diff: 0.780, 276.76MH/s yes! 
[2017-12-09 14:17:08] GPU#1:Gigabyte P106-100, 23.02MH/s 
[2017-12-09 14:17:08] GPU#1:Gigabyte P106-100, 0.3MH/W, 0.013MH/Mhz 
[2017-12-09 14:17:08] GPU#1:Gigabyte P106-100, 54C(F:50%) 1789/2999MHz(76W)

I have been pointing this out but the pool dev replied to normal replies and not to the real issue here with vertcoin mining on this pool.
I have been facing this issue since the day i joined.

Little Miner

newbie

Activity: 19

Merit: 0

Quote from: holda29 on December 09, 2017, 03:55:06 AM

Hi,
I am new to MPH. I am not able to find any readme or guidlines how to properly setup multi algo mining. I created hub worker, turned auto exchange to one coin and now I am supposed to use port 12XXX in my worker. But I am not able to find which port exactly should I use. How about changing between algos like Equihash or Lyra2v2?

Can you confirm, that the right config would look like this?

Code:

ccminer-x64.exe -a lyra2v2 -o stratum+tcp://hub.miningpoolhub.com:12XXX -u user.hubminername -p x

Thanks.

Hi,

You can set these ports for Equihash and Lyra2re2, Equ=12023 and Lyra= 12018.

l33twannabe

newbie

Activity: 35

Merit: 0

Aaronsace, could you please let me know how much time of 24 hours of mining goes for donation purposes ? I don't mind it at all, but just would like to know that.

Also, are these the only algos available on MPH atm: cryptonight,decred,ethash,equihash,groestl,lbry,lyra2z,neoscrypt,pascal,sia,sib (defauls taken from mininpoolhub.bat) ?

papampi

full member

Activity: 686

Merit: 140

Linux FOREVER! Resistance is futile!!!

I'm getting weird low hash rate when mining lyra2rev2 vert and mona
I have 7x270 Mh/s workers so it should be around 1890 mh/s

I know pool shows hash rate based on accepted shares, but its way lower than my workers hash rate
Its ok when I mine equihash and hash rates are almost same, but on lyra2re2 its not

http://oi65.tinypic.com/2lnwc42.jpg

As you can see it never goes over 1100 while it should reach 1800

Using Alexis ccminer
one of my workers output :

Code:

[2017-12-09 14:16:30] [S/A/T]: 0/456/456, diff: 0.779, 276.77MH/s yes! 
[2017-12-09 14:16:30] [S/A/T]: 0/457/457, diff: 0.760, 276.77MH/s yes! 
[2017-12-09 14:16:34] [S/A/T]: 0/458/458, diff: 10.370, 276.77MH/s yes! 
[2017-12-09 14:16:42] GPU#7:Gigabyte P106-100, 22.96MH/s 
[2017-12-09 14:16:42] GPU#7:Gigabyte P106-100, 0.3MH/W, 0.013MH/Mhz 
[2017-12-09 14:16:42] GPU#7:Gigabyte P106-100, 56C(F:50%) 1792/2999MHz(76W) 
[2017-12-09 14:16:42] [S/A/T]: 0/459/459, diff: 4.908, 276.77MH/s yes! 
[2017-12-09 14:16:46] lyra2v2 block 838574, diff 79706.439 
[2017-12-09 14:16:53] lyra2v2 block 838575, diff 79902.176 
[2017-12-09 14:17:07] [S/A/T]: 0/460/460, diff: 0.780, 276.76MH/s yes! 
[2017-12-09 14:17:08] GPU#1:Gigabyte P106-100, 23.02MH/s 
[2017-12-09 14:17:08] GPU#1:Gigabyte P106-100, 0.3MH/W, 0.013MH/Mhz 
[2017-12-09 14:17:08] GPU#1:Gigabyte P106-100, 54C(F:50%) 1789/2999MHz(76W)

djmuk2

newbie

Activity: 36

Merit: 0

Thanks!!

Question - if I set up cgminer to balance between pools will I be penalised by the PPLNS algo or will it just see a lower hash rate - I am not sure how often it would switch between pools.

Quote from: miningpoolhub on December 09, 2017, 04:47:51 AM

Quote from: djmuk2 on December 09, 2017, 04:46:24 AM

Showing all workers with hashrates and coin on one page would be cool so I don't have to play 'hunt the worker' among the individual coin dashboards!!

Yeah that is the highest priority task I'm doing.

miningpoolhub

legendary

Activity: 1456

Merit: 1006

Mining Pool Hub

Quote from: djmuk2 on December 09, 2017, 04:46:24 AM

Showing all workers with hashrates and coin on one page would be cool so I don't have to play 'hunt the worker' among the individual coin dashboards!!

Yeah that is the highest priority task I'm doing.

djmuk2

newbie

Activity: 36

Merit: 0

Showing all workers with hashrates and coin on one page would be cool so I don't have to play 'hunt the worker' among the individual coin dashboards!!

djmuk2

newbie

Activity: 36

Merit: 0

Look at the FAQ
FAQ 2 tells you the EAXACT URL strings you should be using for each algo.

to set up multialgo you need a batch file that will step through starting the miners on each port in turn or set up multiple pools - all explained in FAQ 2...

Quote from: holda29 on December 09, 2017, 03:55:06 AM

Hi,
I am new to MPH. I am not able to find any readme or guidlines how to properly setup multi algo mining. I created hub worker, turned auto exchange to one coin and now I am supposed to use port 12XXX in my worker. But I am not able to find which port exactly should I use. How about changing between algos like Equihash or Lyra2v2?

Can you confirm, that the right config would look like this?

Code:

ccminer-x64.exe -a lyra2v2 -o stratum+tcp://hub.miningpoolhub.com:12XXX -u user.hubminername -p x

Thanks.

aimlor

full member

Activity: 174

Merit: 100

can you also add in GBX or neoscrypt algo?

holda29

newbie

Activity: 18

Merit: 0

Hi,
I am new to MPH. I am not able to find any readme or guidlines how to properly setup multi algo mining. I created hub worker, turned auto exchange to one coin and now I am supposed to use port 12XXX in my worker. But I am not able to find which port exactly should I use. How about changing between algos like Equihash or Lyra2v2?

Can you confirm, that the right config would look like this?

Code:

ccminer-x64.exe -a lyra2v2 -o stratum+tcp://hub.miningpoolhub.com:12XXX -u user.hubminername -p x

Thanks.

Lordas

member

Activity: 142

Merit: 10

Quote from: miningpoolhub on December 08, 2017, 08:57:21 PM

Hi
This is miningpoolhub operator

1. Sorry for late reply.
I am receiving hundreds of emails, skype chats these days. Also bitcointalk, reddit posts are growing rapidly.
I've replied to all email questions.
<...............>

Thanks for service!
And hope to see ETN here some day

MHB

newbie

Activity: 13

Merit: 0

So whats the verdict with MPH after the admin posted about a "crash", is it working properly again?

My zcoin worker shows up intermittently on the dashboard. I mined the entire day yesterday, and the pool stats showed there was no connection. My payout today is also subsequently almost nothing. What the hell MPH?!??
The worker is still mining just as it was yesterday. Same hash rate, no rejected or stale shares etc.

My internet connection is fine as my XMR miner in the same PC seems to be working, even if the payout seems a bit low.

JohnnyDoeTheSecond

newbie

Activity: 24

Merit: 0

Quote from: Pyroboby7 on December 09, 2017, 12:26:44 AM

On another forum I frequent, people were asking about mining pools. A lot of people said, oh NiceHash, I use them and they are great, its so easy! Well, I responded that I used a pool that would allow you to auto exchange. I was called a fool and such, I laughed it off. Woke up the next day to read about the hack. Several others posted about it and asked where they could go.

I told em Miningpoolhub.com and a few said they would check it out. I even PM'd one of the guys I knew that lost his coin from NiceHash to come over to us. Don't know if he did.

This pool has done well. I learned to pull coins after losing my ufocoin when I mined for a bit, then stopped.

SCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERTSCAM ALERT

SCAM ALERT

OH, AND

SCAM ALERT

This imbecile/criminal is telling us to use Megaminer?

Ha.

It works FINE, as long as you are using YOUR computer to mine to HIS addresses.

I changed one thing. ONE THING: i SPECIFIED MY BITCOIN ADDRESS INSTEAD OF HIS, PROGRAM LOCKED UP, REFUSED TO WORK.

GET LOST, SCAMMER.

CryptoSidd

newbie

Activity: 8

Merit: 0

Now i went to pool stats and it's showing 17mh/s and daily income 0.2 vertcoin. I am not crying or anything but there is a problem with vertcoin pool on MPB. My settings are good nd device shows 31.02mh/s with 0 invalid shares. Can someone help me?

meshak

newbie

Activity: 6

Merit: 0

Quote from: XXXJAYXXX on December 08, 2017, 10:42:54 PM

Quote from: jb7032 on December 08, 2017, 10:28:19 PM

Is it normal to not see any hashrate for VERTcoin? Sorry if this was covered previously. I have ~350mh pointed at the algo switching port -17018 and I am seeing unconfirmed transactions come in. Just wasn't sure if this was "normal".

If you are on the autoswitch port.. it will switch to whichever coin is most profitable... so if it happens to be mining something other than vertcoin, you will not see any hashrate reported if it is on Monacoin for example (which uses the same algo as Vertcoin). The unconfirmed coins are coins that have been mined by you.. but are waiting for enough confirmations from the network to be released.

If you want to see the Hashing that has been done while you weren't looking, go down to "graphs" that will actually show you your graphs. I never clicked on it until recently thinking it was likely statistics for the pool itself because of its placement.

CryptoSidd

newbie

Activity: 8

Merit: 0

Quote from: punks on December 09, 2017, 01:23:54 AM

I confirm the same problem with Lyra2RE2. The total my hashrate is 724Mh, but MPH shows me max 450 (the minning is already over a day). Invalid shares less than 1%

I am loving MPH but like the above person I also have this problem with Lyra2RE2. There is only one port available and by workers and config are correct. So i don't know where the actual problem is. I got 0.3 vertcoin with a day mining where as if 31mh/s is taken on mining calculator sites i should mine 0.45 vertcoin.

punks

newbie

Activity: 25

Merit: 0

I confirm the same problem with Lyra2RE2. The total my hashrate is 724Mh, but MPH shows me max 450 (the minning is already over a day). Invalid shares less than 1%

newmz

sr. member

Activity: 372

Merit: 250

The road of excess leads to the palace of wisdom

Quote from: abbv21b on December 09, 2017, 12:52:10 AM

Quote from: CryptoSidd on December 08, 2017, 11:47:47 PM

I am mining vertcoin and i have 31 mh/s but on website it shows 15mh/s and highest it shows 26mh/s.
I am not submitting any bad share so why does it not show actual hashrate? Also vertcoin mining takes long time to show any info. Anyone can help?

As always there will be some delay for the actual mh/s to be updated on dashboard. Give it 15-30 mins and it should match what you are seeing locally.

Your location with respect to the miningpoolhub server you are connecting to - and the ping time you get could also be a factor here. I live in Australia and I have noticed that if I am mining an algorithm that has a server location in Asia, like equihash for example (and usually a ping time of 50-200ms) - my locally reported hash rate and the rate accepted by miningpoolhub are very similar.... BUT if I'm mining an algorith that only has a hub.miningpoolhub.com port, like Lyra2RE2 - the rate accepted by miningpoolhub is generally lower. I think that this is because you submit many more stale shares when it takes much longer for communication between you and the server. I don't know if this is a fact, it's just my guess from watching the results of mining many different algorthms.
It would be great if there were Asia/USA/Europe connections for everything! Maybe there are and I just haven't read all the info correctly but I think they only exist for the very popular algos like dagger/hashimoto, equihash, scrypt, etc. I think Lyra2RE2 has just taken off recently when Mona and Vertcoin prices went right up.

abbv21b

member

Activity: 161

Merit: 10

Quote from: CryptoSidd on December 09, 2017, 01:03:22 AM

Brother i am mining straight for 2 days non stop and it never reached 31mh/s which shows on my miner. That's why i registered asking about this issue. It's currently showing 19mh/s with zero invalid share. So i guess i am earning less coins.

That should not be the case.. maybe check your workers are named and configured correctly?

CryptoSidd

newbie

Activity: 8

Merit: 0

Quote from: abbv21b on December 09, 2017, 12:52:10 AM

Quote from: CryptoSidd on December 08, 2017, 11:47:47 PM

I am mining vertcoin and i have 31 mh/s but on website it shows 15mh/s and highest it shows 26mh/s.
I am not submitting any bad share so why does it not show actual hashrate? Also vertcoin mining takes long time to show any info. Anyone can help?

As always there will be some delay for the actual mh/s to be updated on dashboard. Give it 15-30 mins and it should match what you are seeing locally.

Brother i am mining straight for 2 days non stop and it never reached 31mh/s which shows on my miner. That's why i registered asking about this issue. It's currently showing 19mh/s with zero invalid share. So i guess i am earning less coins.

Topic: [ANN][POOL] Mining Pool Hub - Multipool. Multialgo, Auto Exchange to any coin. - page 147. (Read 487870 times)