ANTMINER S3+ Discussion and Support Thread - page 201.

pekatete

hero member

Activity: 518

Merit: 500

Quote from: shadow2 on September 09, 2014, 01:32:00 PM

the s3+ firmware + the 4.6 cg miner has pretty much got rid of the hardware errors I was getting on one of my S3s. ok it was only 1.5% (according to Mantmonitor) now it's 0.0018%.

you can check the version via the api

Quote

if you are on a remote machine, from another copy of cgminer you can do the following command:

Code:

java API version 192.168.1.99

Where 192.168.1.99 is the S3.

Or on the S3 itself run

Code:

cgminer-api version

I have noticed bursts of hash rate significantly over 500 even though my frequencies shouldn't get the rate that high as I'd get an X in the row of os when using the higher frequencies one is on 237.5 and the other 231.25. just spotted one claiming 657.

Hash spikes are not un-usual when your Diff is still low. Let it run for a while and these will become more reasonable (and these will be in the 5s data). Check again after several hours and again after 24 hrs to get a better picture.

PS. Is there any S3 cgminer 4.6 support thread aside from this?

soy

legendary

Activity: 1428

Merit: 1013

Quote from: shadow2 on September 09, 2014, 01:32:00 PM

the s3+ firmware + the 4.6 cg miner has pretty much got rid of the hardware errors I was getting on one of my S3s. ok it was only 1.5% (according to Mantmonitor) now it's 0.0018%.

you can check the version via the api

Quote

if you are on a remote machine, from another copy of cgminer you can do the following command:

Code:

java API version 192.168.1.99

Where 192.168.1.99 is the S3.

Or on the S3 itself run

Code:

cgminer-api version

I have noticed bursts of hash rate significantly over 500 even though my frequencies shouldn't get the rate that high as I'd get an X in the row of os when using the higher frequencies one is on 237.5 and the other 231.25. just spotted one claiming 657.
[/quote]

Yes, I see the version number in the download URL.

Wonder what frequency the S3+'s will be shipped as. Another 11 days or sooner.... And transit will take how long?

soy

legendary

Activity: 1428

Merit: 1013

Quote from: pekatete on September 09, 2014, 12:39:10 PM

Quote from: soy on September 09, 2014, 12:20:40 PM

Reading the last few pages I opted to install the latest cgminer on what had been the problem S3, #2. Before doing so I ran opkg list-installed | grep cgminer on both S3's so as to ascertain the present version. Both had 3.12.0-1. I downloaded the latest version on #2 and ran opkg list-installed again. Right now I'm guessing that installing via wget and rebooting doesn't update the installed listing as after installation of the latest cgminer the installed list still showed 3.12.0-1. Since that has the lower loads it could be the more efficient miner.

I will install the latest cgminer on #1 and check back a little later today.

After updating cgminer, I think there is another way to ascertain the version than the one installed which was mentioned earlier in the thread. If you use the wget method, ensure you chmod+x the new cgminer before rebooting.

Quote from: soy on September 09, 2014, 12:20:40 PM

The poolside hashrate show #1 to be lower now, GUI 438.38, # 1 having the higher load (2.46) and hardware errors. #1, cat5 connected, seems to have rebooted 22 minutes ago for no reason, now has a low hardware error count (of course only running 22 minutes) of 5, DIFF 449, DiffA 165394, DiffR 0, DiffS 0.

#2 poolside hashrate higher by 11.7%, GUI 440.28, wifi connected, lower load (1.39), DIFF 367, DiffA 6,986,294, DiffR 5505, DiffS 0.

#2 has new thermal paste applied yesterday. I'll be picking more up today and might rip #1 apart to change. Again, I'll download the cgminer to #1 and get back later with new stats.

I'd expect the miner connected via wifi to have a higher DiffR (i.e rejected shares) because of the higher latency inherent in a wifi connection, and your numbers thus far bear this out.
The cat5 connected unit, though showing a lower poolside hash-rate, should have a higher Accepted number (and / or DiffA) compared to the wifi one.
All in all, I would highly recomend updating to the latest cgminer though I have noticed some wierd things since I installed it on my S3's, but in any case, sort your bits and bobs out and get a more accurate picture.

Haven't left for shopping yet, busy, but have some stats.

#1 53minutes (58m slow typist)
   436.51GH/s(avg)
   getworks 117
   accepted 911
   rejected 0
   HW 20
   Utility 16
   discarded 4,596
   stale 0
   localwork 703407
   WU 6,122
   DiffA 351659
   BestShare 1,327,130
   load 1.39 1.36 1.29

#2 53m (59min)
   438.76GH/s
   getworks 115
   accepted 1020
   rejected 0
   HW 33
   utility 18
   discarded 5,016
   stale 0
   LocalWork 705,714
   wu 6,143
   DiffA 258,344
   BestShare 205,663
   load 1.32 1.29 1.25

Pool score about the same for each
Pool hashrate a bit lower for #2 but both look good and running well.





#2

shadow2

newbie

Activity: 17

Merit: 0

the s3+ firmware + the 4.6 cg miner has pretty much got rid of the hardware errors I was getting on one of my S3s. ok it was only 1.5% (according to Mantmonitor) now it's 0.0018%.

you can check the version via the api

Quote

if you are on a remote machine, from another copy of cgminer you can do the following command:

Code:

java API version 192.168.1.99

Where 192.168.1.99 is the S3.

Or on the S3 itself run

Code:

cgminer-api version

I have noticed bursts of hash rate significantly over 500 even though my frequencies shouldn't get the rate that high as I'd get an X in the row of os when using the higher frequencies one is on 237.5 and the other 231.25. just spotted one claiming 657.

pekatete

hero member

Activity: 518

Merit: 500

Quote from: soy on September 09, 2014, 12:20:40 PM

Reading the last few pages I opted to install the latest cgminer on what had been the problem S3, #2. Before doing so I ran opkg list-installed | grep cgminer on both S3's so as to ascertain the present version. Both had 3.12.0-1. I downloaded the latest version on #2 and ran opkg list-installed again. Right now I'm guessing that installing via wget and rebooting doesn't update the installed listing as after installation of the latest cgminer the installed list still showed 3.12.0-1. Since that has the lower loads it could be the more efficient miner.

I will install the latest cgminer on #1 and check back a little later today.

After updating cgminer, I think there is another way to ascertain the version than the one installed which was mentioned earlier in the thread. If you use the wget method, ensure you chmod+x the new cgminer before rebooting.

Quote from: soy on September 09, 2014, 12:20:40 PM

The poolside hashrate show #1 to be lower now, GUI 438.38, # 1 having the higher load (2.46) and hardware errors. #1, cat5 connected, seems to have rebooted 22 minutes ago for no reason, now has a low hardware error count (of course only running 22 minutes) of 5, DIFF 449, DiffA 165394, DiffR 0, DiffS 0.

#2 poolside hashrate higher by 11.7%, GUI 440.28, wifi connected, lower load (1.39), DIFF 367, DiffA 6,986,294, DiffR 5505, DiffS 0.

#2 has new thermal paste applied yesterday. I'll be picking more up today and might rip #1 apart to change. Again, I'll download the cgminer to #1 and get back later with new stats.

I'd expect the miner connected via wifi to have a higher DiffR (i.e rejected shares) because of the higher latency inherent in a wifi connection, and your numbers thus far bear this out.
The cat5 connected unit, though showing a lower poolside hash-rate, should have a higher Accepted number (and / or DiffA) compared to the wifi one.
All in all, I would highly recomend updating to the latest cgminer though I have noticed some wierd things since I installed it on my S3's, but in any case, sort your bits and bobs out and get a more accurate picture.

soy

legendary

Activity: 1428

Merit: 1013

Quote from: pekatete on September 09, 2014, 11:45:34 AM

Quote from: soy on September 09, 2014, 11:10:02 AM

May I ask what determines load? I have two Antminers,

#1 using cat5 connection and its wifi connection disabled has:
loads of 2.70, 2.56, 2.51,
hashrate 441.03,
DIFF 354,
Fan/Temp 3000/41 & 2220/41 room
Temp/Humidity 83°/-%;

and #2 at some distance running via wifi has:
loads of 1.62, 1.47. 1.42,
hashrate 440.80,
DIFF 367,
Fan/Temp 2040/40 & 1860/39,
room Temp/Humidity 80°/39%.

So the first has loads 147% higher than the second? Both S3's at stock frequency.

The biggest load is on an Antminer is cgminer, because it does all the work.
Installing the latest cgminer (which does NOT void your warranty) will, it has been shown, reduce the load by a significant margin.

I am actually surprised at your results, I would have thought the wifi connected antminer would have a higher load than the cat5 connected one, and that it would be reflected in the Diff that has been allocated by the pool, aka I would have expected the cat5 connected ant to have a higher Diff. Could you check your pool-side speeds and see if they reflect the GUI speeds? Also, what are the DiffR numbers for each? (PS. I'll expect a slightly higher DiffR on the wifi connected ant, assuming they are connected to the same pool)

Reading the last few pages I opted to install the latest cgminer on what had been the problem S3, #2. Before doing so I ran opkg list-installed | grep cgminer on both S3's so as to ascertain the present version. Both had 3.12.0-1. I downloaded the latest version on #2 and ran opkg list-installed again. Right now I'm guessing that installing via wget and rebooting doesn't update the installed listing as after installation of the latest cgminer the installed list still showed 3.12.0-1. Since that has the lower loads it could be the more efficient miner.

I will install the latest cgminer on #1 and check back a little later today.

The poolside hashrate show #1 to be lower now, GUI 438.38, # 1 having the higher load (2.46) and hardware errors. #1, cat5 connected, seems to have rebooted 22 minutes ago for no reason, now has a low hardware error count (of course only running 22 minutes) of 5, DIFF 449, DiffA 165394, DiffR 0, DiffS 0.

#2 poolside hashrate higher by 11.7%, GUI 440.28, wifi connected, lower load (1.39), DIFF 367, DiffA 6,986,294, DiffR 5505, DiffS 0.

#2 has new thermal paste applied yesterday. I'll be picking more up today and might rip #1 apart to change. Again, I'll download the cgminer to #1 and get back later with new stats.

pekatete

hero member

Activity: 518

Merit: 500

Quote from: Stratobitz on September 09, 2014, 12:03:41 PM

Do you know by chance how much of a load reduction is realized with the new CGMiner? We've ordered a number of the new S3+ units and am wondering what PSU wattage would be needed for 1 unit pending they've rated it with the older version. I was planning on 500w PSUs for singles... Perhaps 400s would work?

Thanks!

Strato

Don't get in a muddle here. Decreasing CPU load does NOT decrease the power consumption of the unit to any significant level.
*** START PINCH OF SALT *** I could argue that it creates "freedom" for the CPU to process even more data thus increase power consumption. *** END PINCH OF SALT ***

I'd say stick to a 500 watt PSU or even better a 550 watt PSU for a single unit.

Count_Frackula

member

Activity: 99

Merit: 10

Quote from: Stratobitz on September 09, 2014, 12:03:41 PM

Quote from: pekatete on September 09, 2014, 11:45:34 AM

Quote from: soy on September 09, 2014, 11:10:02 AM

May I ask what determines load? I have two Antminers,

#1 using cat5 connection and its wifi connection disabled has:
loads of 2.70, 2.56, 2.51,
hashrate 441.03,
DIFF 354,
Fan/Temp 3000/41 & 2220/41 room
Temp/Humidity 83°/-%;

and #2 at some distance running via wifi has:
loads of 1.62, 1.47. 1.42,
hashrate 440.80,
DIFF 367,
Fan/Temp 2040/40 & 1860/39,
room Temp/Humidity 80°/39%.

So the first has loads 147% higher than the second? Both S3's at stock frequency.

The biggest load is on an Antminer is cgminer, because it does all the work.
Installing the latest cgminer (which does NOT void your warranty) will, it has been shown, reduce the load by a significant margin.

I am actually surprised at your results, I would have thought the wifi connected antminer would have a higher load than the cat5 connected one, and that it would be reflected in the Diff that has been allocated by the pool, aka I would have expected the cat5 connected ant to have a higher Diff. Could you check your pool-side speeds and see if they reflect the GUI speeds? Also, what are the DiffR numbers for each? (PS. I'll expect a slightly higher DiffR on the wifi connected ant, assuming they are connected to the same pool)

Do you know by chance how much of a load reduction is realized with the new CGMiner? We've ordered a number of the new S3+ units and am wondering what PSU wattage would be needed for 1 unit pending they've rated it with the older version. I was planning on 500w PSUs for singles... Perhaps 400s would work?

Thanks!

Strato

I wouldn't expect power consumption to be significantly impacted. The load average is usually on a small router-grade CPU that the units use to run the basic functions. Power-wise, the core OS probably uses a maximum of about 1 amp (though I suspect it's less than .5 amps). Less load on this probably affects that power draw by 10% - maybe 20%. In short, you're talking about a less than a 200 MA difference in power draw, at best.

Stratobitz

legendary

Activity: 1022

Merit: 1010

Quote from: pekatete on September 09, 2014, 11:45:34 AM

Quote from: soy on September 09, 2014, 11:10:02 AM

May I ask what determines load? I have two Antminers,

#1 using cat5 connection and its wifi connection disabled has:
loads of 2.70, 2.56, 2.51,
hashrate 441.03,
DIFF 354,
Fan/Temp 3000/41 & 2220/41 room
Temp/Humidity 83°/-%;

and #2 at some distance running via wifi has:
loads of 1.62, 1.47. 1.42,
hashrate 440.80,
DIFF 367,
Fan/Temp 2040/40 & 1860/39,
room Temp/Humidity 80°/39%.

So the first has loads 147% higher than the second? Both S3's at stock frequency.

The biggest load is on an Antminer is cgminer, because it does all the work.
Installing the latest cgminer (which does NOT void your warranty) will, it has been shown, reduce the load by a significant margin.

I am actually surprised at your results, I would have thought the wifi connected antminer would have a higher load than the cat5 connected one, and that it would be reflected in the Diff that has been allocated by the pool, aka I would have expected the cat5 connected ant to have a higher Diff. Could you check your pool-side speeds and see if they reflect the GUI speeds? Also, what are the DiffR numbers for each? (PS. I'll expect a slightly higher DiffR on the wifi connected ant, assuming they are connected to the same pool)

Do you know by chance how much of a load reduction is realized with the new CGMiner? We've ordered a number of the new S3+ units and am wondering what PSU wattage would be needed for 1 unit pending they've rated it with the older version. I was planning on 500w PSUs for singles... Perhaps 400s would work?

Thanks!

Strato

pekatete

hero member

Activity: 518

Merit: 500

Quote from: soy on September 09, 2014, 11:10:02 AM

May I ask what determines load? I have two Antminers,

#1 using cat5 connection and its wifi connection disabled has:
loads of 2.70, 2.56, 2.51,
hashrate 441.03,
DIFF 354,
Fan/Temp 3000/41 & 2220/41 room
Temp/Humidity 83°/-%;

and #2 at some distance running via wifi has:
loads of 1.62, 1.47. 1.42,
hashrate 440.80,
DIFF 367,
Fan/Temp 2040/40 & 1860/39,
room Temp/Humidity 80°/39%.

So the first has loads 147% higher than the second? Both S3's at stock frequency.

The biggest load is on an Antminer is cgminer, because it does all the work.
Installing the latest cgminer (which does NOT void your warranty) will, it has been shown, reduce the load by a significant margin.

I am actually surprised at your results, I would have thought the wifi connected antminer would have a higher load than the cat5 connected one, and that it would be reflected in the Diff that has been allocated by the pool, aka I would have expected the cat5 connected ant to have a higher Diff. Could you check your pool-side speeds and see if they reflect the GUI speeds? Also, what are the DiffR numbers for each? (PS. I'll expect a slightly higher DiffR on the wifi connected ant, assuming they are connected to the same pool)

soy

legendary

Activity: 1428

Merit: 1013

May I ask what determines load? I have two Antminers,

#1 using cat5 connection and its wifi connection disabled has:
loads of 2.70, 2.56, 2.51,
hashrate 441.03,
DIFF 354,
Fan/Temp 3000/41 & 2220/41 room
Temp/Humidity 83°/-%;

and #2 at some distance running via wifi has:
loads of 1.62, 1.47. 1.42,
hashrate 440.80,
DIFF 367,
Fan/Temp 2040/40 & 1860/39,
room Temp/Humidity 80°/39%.

So the first has loads 147% higher than the second? Both S3's at stock frequency.

Rabinovitch

legendary

Activity: 2030

Merit: 1076

A humble Siberian miner

Quote from: Moria843 on September 09, 2014, 09:11:45 AM

U.FL Mini PCI to RP-SMA Pigtail Antenna WiFi Cable

http://www.amazon.com/dp/B005UWD0EG/ref=wl_it_dp_o_pC_S_ttl?_encoding=UTF8&colid=1Y1X7ERWVNU04&coliid=I21TKF96CS296O

You are right. I've ordered 4 such pigtails. And 2 antennas. ) My order has already arrived in Russia and passed the customs. Roll Eyes

http://www.dx.com/p/182752

http://www.dx.com/p/5259

Moria843

sr. member

Activity: 442

Merit: 250

Found Lost beach - quiet now

B8 order in, need to connect wireless. Will pigtail below work for S3?

I want to make sure it has the right connector.

U.FL Mini PCI to RP-SMA Pigtail Antenna WiFi Cable

http://www.amazon.com/dp/B005UWD0EG/ref=wl_it_dp_o_pC_S_ttl?_encoding=UTF8&colid=1Y1X7ERWVNU04&coliid=I21TKF96CS296O

jelin1984

legendary

Activity: 2408

Merit: 1004

What is the best moddiff for s3

Fahlcor

full member

Activity: 139

Merit: 100

Quote from: Fahlcor on September 08, 2014, 11:51:32 PM

Quote from: Count_Frackula on September 08, 2014, 05:23:22 PM

Give it a shot, and please feel free to use me as a referral: http://www.miningrigrentals.com/register?ref=126

ok setup 12 ants to use it. Will give it a try. Thx and used you are refer.

Fahlcor

Had my stuff rented 3 time already back to back. turning up the price each time ;-) The ants don't seem to mind it at all.

Thanks for the tip. Anyone looking to purely ROI should have a look at this.

s1lverbox

legendary

Activity: 2324

Merit: 1039

Quote from: BITMAIN on September 08, 2014, 10:44:06 PM

Quote from: bobsag3 on September 08, 2014, 01:00:19 PM

Heads up guys, if you update your CGMiner beyond what it comes with, bitmain will deny you any future RMA

Source: They denied several of my S1s back in the day when I applied Kano's fix.

Hi bobsag3,

Your above lines are not true, we sincerely support RMA for any tech issues except for overclocking.
We really appreciate Kano's work.

i remember when S1 delivered by BITMAIN was overclocked. and on that case RMA didn't support.
I will dig to find it. but in original thread there were few issues like that. .

pekatete

hero member

Activity: 518

Merit: 500

Quote from: BITMAIN on September 08, 2014, 10:44:06 PM

Quote from: bobsag3 on September 08, 2014, 01:00:19 PM

Heads up guys, if you update your CGMiner beyond what it comes with, bitmain will deny you any future RMA

Source: They denied several of my S1s back in the day when I applied Kano's fix.

Hi bobsag3,

Your above lines are not true, we sincerely support RMA for any tech issues except for overclocking.
We really appreciate Kano's work.

Thanks for clearing that up. It seemed a bit far-fetched and clearly bobsag3 has a history with Bitmain.

Fahlcor

full member

Activity: 139

Merit: 100

Quote from: Count_Frackula on September 08, 2014, 05:23:22 PM

Give it a shot, and please feel free to use me as a referral: http://www.miningrigrentals.com/register?ref=126

ok setup 12 ants to use it. Will give it a try. Thx and used you are refer.

Fahlcor

visdude

legendary

Activity: 1081

Merit: 1001

Quote from: BITMAIN on September 08, 2014, 10:44:06 PM

Quote from: bobsag3 on September 08, 2014, 01:00:19 PM

Heads up guys, if you update your CGMiner beyond what it comes with, bitmain will deny you any future RMA

Source: They denied several of my S1s back in the day when I applied Kano's fix.

Hi bobsag3,

Your above lines are not true, we sincerely support RMA for any tech issues except for overclocking.
We really appreciate Kano's work.

Bitmain,

How soon are you then going to release a proper firmware with the latest cgminer in it? If I remember correctly, you sorta promised somewhere in here to have it in two weeks and that was, I think, over three weeks ago.

Count_Frackula

member

Activity: 99

Merit: 10

Quote from: BITMAIN on September 08, 2014, 10:44:06 PM

Quote from: bobsag3 on September 08, 2014, 01:00:19 PM

Heads up guys, if you update your CGMiner beyond what it comes with, bitmain will deny you any future RMA

Source: They denied several of my S1s back in the day when I applied Kano's fix.

Hi bobsag3,

Your above lines are not true, we sincerely support RMA for any tech issues except for overclocked miners.
We really appreciate Kano's work.

Even if it were true, you could always just flash them with stock firmware before doing a RMA. Sounds kinda fishy to me.

Topic: ANTMINER S3+ Discussion and Support Thread - page 201. (Read 710164 times)