Does this also apply if the Overclock GPU box is UNticked?
Yes All adapters that are seen in AOCLBF will be set to default 
Topic: AOCLBF 1.81 - Dynamic clocks adjusting Manual fanspeed on startup - page 2. (Read 7353 times)
August 16, 2011, 04:33:34 PM
August 16, 2011, 04:25:18 PM
Welcome to 1.8 release! Now phoenix 1.6.x full compatible!
"6. Set to default all adapters on exit"
Does this also apply if the Overclock GPU box is UNticked?
edit; Good idea with the console window, could be nice to be able to see what phoenix is showing.
August 16, 2011, 02:44:55 PM
huayra.agera thank you
I think there is a way but gui by autoit is hard one. There is no a form template available to do this easy. Only manual work editing script...But maybe I'll try
I think there is a way but gui by autoit is hard one. There is no a form template available to do this easy. Only manual work editing script...But maybe I'll try
No, thank YOU! I just love this app compared to the others.
I'll chip in once I have enough to give. Keep up the good work. Like I always say, how I wish I have your coding skills I would have taken over the development. I can only give ideas so far. August 16, 2011, 02:32:41 PM
huayra.agera thank you
I think there is a way but gui by autoit is hard one. There is no a form template available to do this easy. Only manual work editing script...But maybe I'll try
I think there is a way but gui by autoit is hard one. There is no a form template available to do this easy. Only manual work editing script...But maybe I'll try
August 16, 2011, 02:19:16 PM
Nice one! Testing away. I just remembered, I have a suggestion, is there any way we could resize the whole window? If you noticed there's no way to do that.
Oh and a way to hide the OSDs.
One last, a console like window comparable to the summary page of the GUI Miner.
I believe you can now post in the Mining Support board so that you're work will be seen by more people; just link to original post. Regards! =)
Oh and a way to hide the OSDs.
One last, a console like window comparable to the summary page of the GUI Miner.
I believe you can now post in the Mining Support board so that you're work will be seen by more people; just link to original post. Regards! =)
August 16, 2011, 01:58:41 PM
Welcome to 1.8 release! Now phoenix 1.6.x full compatible!
August 15, 2011, 12:49:45 PM
Hi! Is there a way for you to add support/checkbox for phatk2. I'm trying out the new Phoenix 1.6.1. Thanks! =)
If you save phatk2 in the same folder as phatk you can run it that way till its added.
Is there anyway to add a minimize on start feature to hide this program when the computer boots up?
What I did instead is uncheck phatk and write on the extra flags -k phatk2. It worked.
August 14, 2011, 10:04:04 PM
great, hope dynamic voltage clocks adjustable in next version 
August 14, 2011, 04:54:01 PM
Hi! Is there a way for you to add support/checkbox for phatk2. I'm trying out the new Phoenix 1.6.1. Thanks! =)
If you save phatk2 in the same folder as phatk you can run it that way till its added.
Is there anyway to add a minimize on start feature to hide this program when the computer boots up?
August 13, 2011, 07:17:37 PM
Code:
AutoIt Error
Line 8690 (blahblah.exe);
Error: Subscript used with non-Array variable.
August 13, 2011, 02:38:52 PM
huayra.agera
have no time but will try to do smth
have no time but will try to do smth
I'm trying out the new Phoenix 1.6.1. Thanks! =)
what results? how much Mhashes up? August 13, 2011, 10:26:32 AM
Hi! Is there a way for you to add support/checkbox for phatk2. I'm trying out the new Phoenix 1.6.1. Thanks! =)
August 10, 2011, 10:23:42 AM
Hi! Sorry, had a hard time searching for this thread again. I think the mods should inlcude a Child Board under Mining Support for "Mods". =).
Anyways, you're mod is doing great actually.
I have one thing, the OSD seems to be limited when the title/name of the card is longer than 1 character, it cuts the whole OSD line (the % of the fan). So I just named the miners i., ii and so on. I hope I made a point. =).
I haven't tested yet extensively the clocks settings as well as the fan if they are saving, since I have multiple machines I'm deploying this to. But I'll report my findings at once. =)
Anyways, you're mod is doing great actually.
I have one thing, the OSD seems to be limited when the title/name of the card is longer than 1 character, it cuts the whole OSD line (the % of the fan). So I just named the miners i., ii and so on. I hope I made a point. =).
I haven't tested yet extensively the clocks settings as well as the fan if they are saving, since I have multiple machines I'm deploying this to. But I'll report my findings at once. =)
August 09, 2011, 02:22:48 PM
i was really impressed with this program, until i tried to save the mem/core clock speeds and it caused the PC to lock up, as it applied the speed, but not the fan, and then not the voltage, etc. and then only to one card. it might have been an older version but it was annoying at the time.
What a version of program did you use? Some remarks about 1.77 release: when you push on Clock Speed you can manage the autostart of Core, Memory and voltage only. You must push Fan Speed button to manage the autostart of fanspeed. There must be a fanspeed value in the appropriate section of Clocks.ini after that. If you have 2 or more videocards the clock speed and fan speed buttons must be pushed in each tab corresponding to your adapter.it also makes sure to return clock/fan/voltage rates back to normal when you close the window or quit cgminer, which can be a help when you need to shut down, be in the same room as 4 GPU fans at 70-80%, or play games for a few hours and return to mining, etc.
the feature to return clock/fan/voltage rates to default on exit may be realized in the future versions. August 09, 2011, 12:07:33 PM
i was really impressed with this program, until i tried to save the mem/core clock speeds and it caused the PC to lock up, as it applied the speed, but not the fan, and then not the voltage, etc. and then only to one card. it might have been an older version but it was annoying at the time.
i did end up editing the ini files, but the clock rates didn't apply properly, and i had to reboot into safe mode to tweak overclock rates. i think the main problem was that the fans didnt kick in or allow easy granular control via the sliders, you could set 40 and hit fan speed, and then you'd move the slider to 55 and it wouldn't set unless you did it quickly. again, older version.
that said, it's a great program for unattended use, and had it running for 5 hours, with each card having different rates and performance settings. it works great.
at the moment, i find it's easier to use barelyclocked and cgminer in a batch script and put a shortcut to the start.bat file in the startup folder, it also makes sure to return clock/fan/voltage rates back to normal when you close the window or quit cgminer, which can be a help when you need to shut down, be in the same room as 4 GPU fans at 70-80%, or play games for a few hours and return to mining, etc.
i did end up editing the ini files, but the clock rates didn't apply properly, and i had to reboot into safe mode to tweak overclock rates. i think the main problem was that the fans didnt kick in or allow easy granular control via the sliders, you could set 40 and hit fan speed, and then you'd move the slider to 55 and it wouldn't set unless you did it quickly. again, older version.
that said, it's a great program for unattended use, and had it running for 5 hours, with each card having different rates and performance settings. it works great.
at the moment, i find it's easier to use barelyclocked and cgminer in a batch script and put a shortcut to the start.bat file in the startup folder, it also makes sure to return clock/fan/voltage rates back to normal when you close the window or quit cgminer, which can be a help when you need to shut down, be in the same room as 4 GPU fans at 70-80%, or play games for a few hours and return to mining, etc.
August 09, 2011, 10:25:20 AM
huayra.agera
Waiting for your test results
Waiting for your test results
August 08, 2011, 10:00:39 PM
Wow! Thanks for continuing on his great work. I'll be testing your mod. =)
August 06, 2011, 12:19:53 PM
Xanderus
Boзмoжнo нo нe xoтeлocь бы излишнe нaгpyжaть интepфeйc дoп гaлoчкaми и пoлями...пoдyмaю eщё
It's possible but wouldn't like to unduly burden the interface additional checkboxes and inputboxes ... think about it yet
Boзмoжнo нo нe xoтeлocь бы излишнe нaгpyжaть интepфeйc дoп гaлoчкaми и пoлями...пoдyмaю eщё
It's possible but wouldn't like to unduly burden the interface additional checkboxes and inputboxes ... think about it yet
August 05, 2011, 10:08:03 AM
Ecли yж дoбaвлeнa фyнкция ycтaнoвки вeнтилятopoв, тo мoжнo к измeнeнию чacтoты дoбaвить и измeнeниe oбopoтoв кyлepa в зaвиcимocти oт тeмпepaтypы (пpи пepeгpeвe выcтaвлять кyлep нa XX% или нa мaкcимyм, пpи вoзвpaтe тeмпepaтypы в лимиты cтaвить нa YY или нa aвтo; XX и YY - выcтaвляeт юзep). Taкoe вoзмoжнo?
Пepeвoд для бypжyeв:
If there is a function of fan speed setting, that possible to clock ajustment add a fan speed change depending of temperature (set fan to XX% or maximum when overheating, set to YY% or auto whet temp returns to limits; XX and YY is user settings) Can it be done?
Пepeвoд для бypжyeв:
If there is a function of fan speed setting, that possible to clock ajustment add a fan speed change depending of temperature (set fan to XX% or maximum when overheating, set to YY% or auto whet temp returns to limits; XX and YY is user settings) Can it be done?
August 04, 2011, 03:02:52 PM
New version 1.77 released!
Jump to: