Topic: arOpenCLMAX v0.1b - MAX coin OpenCL miner - Works with AMD, NVIDIA XPT - 1GH! - page 25. (Read 39037 times)
February 07, 2014, 11:39:45 AM
I am using your miner now, it's working fine. However both my cards only have around 80% load. I am running with 'gpu max alloc =100', but that doesn't seem to change anything. They are 5870's on a windows 7 x64 system. Anything I can do about this?
February 07, 2014, 11:35:27 AM
Why would you make a miner, that works only on one pool?
1gh works and pays.
And 1gh is down, just as I say that 1gh works and pays.
February 07, 2014, 11:33:29 AM
Why would you make a miner, that works only on one pool?
1gh works and pays.
1gh works and pays.
February 07, 2014, 11:33:26 AM
I see shares on ypool but
BALANCE (MAX)
0.00000000
UNCONFIRMED (MAX)
0.00000000
BALANCE (MAX)
0.00000000
UNCONFIRMED (MAX)
0.00000000
It's been doing that for hours, even with cpu mining. 1gh hasn't been paying out either. Everything was going great until this morning
1GH payouts are fine at my end.
February 07, 2014, 11:31:54 AM
I see shares on ypool but
BALANCE (MAX)
0.00000000
UNCONFIRMED (MAX)
0.00000000
BALANCE (MAX)
0.00000000
UNCONFIRMED (MAX)
0.00000000
February 07, 2014, 11:28:25 AM
connect lost, try later 45s 
February 07, 2014, 11:25:48 AM
I can't even open ypool.
February 07, 2014, 11:25:33 AM
is this working just at ypool or on 1gh too ??
February 07, 2014, 11:22:41 AM
thank you ,
i got 6x280x 1.18G
i got 6x280x 1.18G
February 07, 2014, 11:21:19 AM
I guess not all shares are valid.
As per minner, I have very low reject ratio.
Code:
[00:31:27] kHash/s: 185670.47 Shares total: 653 / 641
[00:31:30] Share found! (Blockheight: 2521)
[00:31:33] Share found! (Blockheight: 2521)
[00:31:35] kHash/s: 185678.19 Shares total: 655 / 643
[00:31:40] Share found! (Blockheight: 2521)
[00:31:42] Share found! (Blockheight: 2521)
[00:31:43] kHash/s: 185685.56 Shares total: 657 / 645
[00:31:46] Share found! (Blockheight: 2521)
[00:31:47] Share found! (Blockheight: 2521)
[00:31:48] Share found! (Blockheight: 2521)
New block data - height: 2522 tx count: 7
[00:31:51] kHash/s: 185692.60 Shares total: 660 / 648
[00:31:59] kHash/s: 185699.86 Shares total: 660 / 648
New block data - height: 2523 tx count: 1
February 07, 2014, 11:21:04 AM
Ypool is having problems. Have been for hours.
February 07, 2014, 11:19:55 AM
I guess not all shares are valid.
February 07, 2014, 11:19:06 AM
Something wrong with ypool? I don't see my balance (both confirmed and unconfirmed) changing, just shares value is increasing :confused Its been quite a while
February 07, 2014, 11:16:23 AM
try -d 0 or -d 1
Please stay away from this thread!
February 07, 2014, 11:15:12 AM
arOpenCLMAX -o http://ypool.net:8080 -u myworkername -p myworkerpass
is not working... says wrong workername or password...
is not working... says wrong workername or password...
Check what it says
100% sure it's not the program's error check the workername and pass
February 07, 2014, 11:14:06 AM
ypool backup or die 
February 07, 2014, 11:12:13 AM
arOpenCLMAX -o http://ypool.net:8080 -u myworkername -p myworkerpass
is not working... says wrong workername or password...
is not working... says wrong workername or password...
Check what it says
100% sure it's not the program's error check the workername and pass
February 07, 2014, 11:11:28 AM
I get invalid checksum on 5870s
February 07, 2014, 11:11:25 AM
Is it possible to use a config file with this? And if so, how to call it? arOpenCLMAX.conf?
February 07, 2014, 11:10:49 AM
arOpenCLMAX -o http://ypool.net:8080 -u myworkername -p myworkerpass
is not working... says wrong workername or password...
is not working... says wrong workername or password...
Check what it says
EDIT: Nevermind, fixed it. Forgot I have to put my username then workername. I'm used that is says Sparkzor.xxxx and not just xxxx
Jump to: