Hello guys,
There might be a simple solution.
This happened to me as well. Added all the risers in the mother board.. and the fans started working but no image on the display.
From all of the 13gpu connectors in the motherboard ... Remove the riser from the standard size one.
The rig should start now.. delete ..go into bios..and change primary display adaptor to "ONBoard "
When a video card is connected in the big connector the motherboard will not display anithing from the onboard connection.
Topic: ASRock H110 dont work need help! (Read 1311 times)
Ok so now on the device manager I have 3 cards showing - 1 is fully detected and 2 are hidden, 4th card not yet showing anything.. that's still some progress to me because none were showing prior. Any suggestions where I can go from there? It says error code 45 on the hidden ones.
Hidden devices is junk that you better get rid of. Do DDU and install drivers manually (point and click to the unzipped driver dir from device manager) I had a similar problem and it turned out to be the power supply. I switched from a 1000W EVGA to a 1200W Seasonic and then everything booted just fine.
Ok so now on the device manager I have 3 cards showing - 1 is fully detected and 2 are hidden, 4th card not yet showing anything.. that's still some progress to me because none were showing prior. Any suggestions where I can go from there? It says error code 45 on the hidden ones.
you can try to boot with different display connectors. DVI may work the best, sometimes some playing around is required. also do boot with a single card initially. try other cards, try card in slot... etc.
also see if your ethernet leds are blinking - it's an indicator that the problem is after bois post, otherwise check cpu and ram ...
EDIT: ohhh you're at later stages now sorry.... just yesterday did setup of three of these mobos( 8 to 12 gups each) -> 0 issues
also see if your ethernet leds are blinking - it's an indicator that the problem is after bois post, otherwise check cpu and ram ...
EDIT: ohhh you're at later stages now sorry.... just yesterday did setup of three of these mobos( 8 to 12 gups each) -> 0 issues
You may try to load default BIOS settings and keep minimal components connected to power. Then gradually adding more components to see which one is faulty.
One card was detected so far and that was the one I input on the PCIE 3.0 16x slot earlier and put back on riser, I've added another 3 GPU with risers but they won't detect - 1 is also hidden for some reason code 45 error, the other two don't exist.
I hope I don't have to put each GPU on the 16x slot on the MB first then back on the riser..
What do you think?
Well, if it resolves the issue then go for it
You may try to load default BIOS settings and keep minimal components connected to power. Then gradually adding more components to see which one is faulty.
One card was detected so far and that was the one I input on the PCIE 3.0 16x slot earlier and put back on riser, I've added another 3 GPU with risers but they won't detect - 1 is also hidden for some reason code 45 error, the other two don't exist.
I hope I don't have to put each GPU on the 16x slot on the MB first then back on the riser..
What do you think?
You may try to load default BIOS settings and keep minimal components connected to power. Then gradually adding more components to see which one is faulty.
You could setting PCIE to GEN 1 or GEN 2 in BIOS.
Tried, didn't work..
Guys I'm having a similar issue - I have a hunch it's the risers not getting any power..
Asrock H110 MB have all the wiring and setup done on it and both molex connectors for PCIE on MB connected - When I connect an EVGA 1080ti FTW3 to the PCIE16 directly on the MB it works fine and is detected on windows and I am able to update drivers etc and have done so.
As soon as I connected it to a riser on the first black PCIE slot closest to CPU it won't detect it at all. Tried switching risers, tried switching GPUs (Have 16), tried using different type of riser, tried a riser that is working for existing miner, tried direct molex cable from EVGA 1600W P2 PSU to riser, tried SATA to molex.. I have no idea what else to do - haven't updated any bios or changed any settings on MB - Fresh new parts and windows install 10 pro.
Can someone kindly help please? I am using exact same parts from previous miner and have only bought an extra 1600W EVGA psu to support MB and 2 GPU and use 2x Corsair 1000W to support the final 6 GPUs
Any advice?
Regards
Asrock H110 MB have all the wiring and setup done on it and both molex connectors for PCIE on MB connected - When I connect an EVGA 1080ti FTW3 to the PCIE16 directly on the MB it works fine and is detected on windows and I am able to update drivers etc and have done so.
As soon as I connected it to a riser on the first black PCIE slot closest to CPU it won't detect it at all. Tried switching risers, tried switching GPUs (Have 16), tried using different type of riser, tried a riser that is working for existing miner, tried direct molex cable from EVGA 1600W P2 PSU to riser, tried SATA to molex.. I have no idea what else to do - haven't updated any bios or changed any settings on MB - Fresh new parts and windows install 10 pro.
Can someone kindly help please? I am using exact same parts from previous miner and have only bought an extra 1600W EVGA psu to support MB and 2 GPU and use 2x Corsair 1000W to support the final 6 GPUs
Any advice?
Regards
You could setting PCIE to GEN 1 or GEN 2 in BIOS.
Guys I'm having a similar issue - I have a hunch it's the risers not getting any power..
Asrock H110 MB have all the wiring and setup done on it and both molex connectors for PCIE on MB connected - When I connect an EVGA 1080ti FTW3 to the PCIE16 directly on the MB it works fine and is detected on windows and I am able to update drivers etc and have done so.
As soon as I connected it to a riser on the first black PCIE slot closest to CPU it won't detect it at all. Tried switching risers, tried switching GPUs (Have 16), tried using different type of riser, tried a riser that is working for existing miner, tried direct molex cable from EVGA 1600W P2 PSU to riser, tried SATA to molex.. I have no idea what else to do - haven't updated any bios or changed any settings on MB - Fresh new parts and windows install 10 pro.
Can someone kindly help please? I am using exact same parts from previous miner and have only bought an extra 1600W EVGA psu to support MB and 2 GPU and use 2x Corsair 1000W to support the final 6 GPUs
Any advice?
Regards
Asrock H110 MB have all the wiring and setup done on it and both molex connectors for PCIE on MB connected - When I connect an EVGA 1080ti FTW3 to the PCIE16 directly on the MB it works fine and is detected on windows and I am able to update drivers etc and have done so.
As soon as I connected it to a riser on the first black PCIE slot closest to CPU it won't detect it at all. Tried switching risers, tried switching GPUs (Have 16), tried using different type of riser, tried a riser that is working for existing miner, tried direct molex cable from EVGA 1600W P2 PSU to riser, tried SATA to molex.. I have no idea what else to do - haven't updated any bios or changed any settings on MB - Fresh new parts and windows install 10 pro.
Can someone kindly help please? I am using exact same parts from previous miner and have only bought an extra 1600W EVGA psu to support MB and 2 GPU and use 2x Corsair 1000W to support the final 6 GPUs
Any advice?
Regards
I bought again a new MB. Now its working
Hello,
ive started today my first mining rig.
My Setup:
1x MB ASRock H110 Pro BTC+ 1151 ATX DVI DDR4 retail
1x DDR4 16GB PC 2400 CL15 G.Skill (1x16GB) 16GIS Aegis 4
1x Plus 120GB
1x Intel Pentium G4400 3300 1151 BOX*
2x Server PSU 2400 Watt
8x Vega 64
When i start the rig only fans are spinning(CPU, Graficcard) and graficcard led "Radeon" is on but no signal on my monitor.
I connected for first start:
1x 16 GB RAM DDR4 2400 mhs
2x Molex 4pin
1x 24 pin atx
1x SATA 15pin
1x 4pin CPU power (on a 8 pin slot)
1x Vega 64
Monitor is working tested on my Laptop.
Graficard fan is working and leds.
Graficcard connected both 2x 8 pin power
I tested also another graficcard same happens.
I tested diffrent risers also no signal.
Risers are powered and usb correct connected.
Ram tested on first slot and on second slot
Anyone could help me?
ive started today my first mining rig.
My Setup:
1x MB ASRock H110 Pro BTC+ 1151 ATX DVI DDR4 retail
1x DDR4 16GB PC 2400 CL15 G.Skill (1x16GB) 16GIS Aegis 4
1x Plus 120GB
1x Intel Pentium G4400 3300 1151 BOX*
2x Server PSU 2400 Watt
8x Vega 64
When i start the rig only fans are spinning(CPU, Graficcard) and graficcard led "Radeon" is on but no signal on my monitor.
I connected for first start:
1x 16 GB RAM DDR4 2400 mhs
2x Molex 4pin
1x 24 pin atx
1x SATA 15pin
1x 4pin CPU power (on a 8 pin slot)
1x Vega 64
Monitor is working tested on my Laptop.
Graficard fan is working and leds.
Graficcard connected both 2x 8 pin power
I tested also another graficcard same happens.
I tested diffrent risers also no signal.
Risers are powered and usb correct connected.
Ram tested on first slot and on second slot
Anyone could help me?
Use DDR4 2133Mhz RAM.. I guess it will work.
Mini miner could be right, thoght I have heard that MOBO in that case just clocks down Your RAM frequency to suitable one.
On paper Your CPU supported memory types are:
DDR4-1866/2133, DDR3L-1333/1600 @ 1.35V
If You have any RAM sticks with mentioned frequencies, You can give them a try.
Worth taking a look:
https://ark.intel.com/products/88179/Intel-Pentium-Processor-G4400-3M-Cache-3_30-GHz
thanks. I read this processor specs before i bought this cpu (same MB and processor ).it works
Thanks for reply.
Ive tested now other DDR4 Ram 2x 4 GB dosnt work
Now only CPU and MB left. I would say the asrock h110 is not working.
Could anyone check if my components fits together (scroll up) CPU, Ram, MB.
Ill change the MB on Monday.
Ive tested now other DDR4 Ram 2x 4 GB dosnt work
Now only CPU and MB left. I would say the asrock h110 is not working.
Could anyone check if my components fits together (scroll up) CPU, Ram, MB.
Ill change the MB on Monday.
Are You using a PICO adapter to connect Your server PSU to motherboard (maybe bad PICO)? https://www.amazon.com/Insten-24-pin-Power-Supply-Tester/dp/B005CTCD6S these can come really handy in situations like that.
And how are Your 2 separate server PSUs connected together (are You using both of them?), both plugged into an extension cord or do You have some other trick for simultaneous power-on?
But if still no POST, then MB is probably bad (I tried to get mine working for almost 3 weeks, really stupid decision
. Should have just got another one and continued to mine).Thank you for your reply i already ordered your recommended device for my country. Thank you.
Ive a pico adapter but ive two psu and two pico adapter. For first start i connected 1 psu direct to the mb and only one grafic.
I tested both pico adapters for 1 PSU i thought the same maybe the pico wont work.
I tested my ram not working. I tested 2x 4GB 2133 mhs also not working. Ive a 2x 24 pin to 1 24pin adapter for connecting both psu(But for first start i didnt used it).
Everything tested on other devices.
Ive also tested to start only with on board grafic also dont work.
Ive tested diffrent risers and also direct connect to the mb also not working.
Still untested MB and CPU.
But i guess MB is gone.
Saddly does seem so
. You really have done some serious troubleshooting what should have had revealed the problem. After all that You can pretty much say with confidence that it is the hardware that is failing at the moment. Thanks for reply.
Ive tested now other DDR4 Ram 2x 4 GB dosnt work
Now only CPU and MB left. I would say the asrock h110 is not working.
Could anyone check if my components fits together (scroll up) CPU, Ram, MB.
Ill change the MB on Monday.
Ive tested now other DDR4 Ram 2x 4 GB dosnt work
Now only CPU and MB left. I would say the asrock h110 is not working.
Could anyone check if my components fits together (scroll up) CPU, Ram, MB.
Ill change the MB on Monday.
Are You using a PICO adapter to connect Your server PSU to motherboard (maybe bad PICO)? https://www.amazon.com/Insten-24-pin-Power-Supply-Tester/dp/B005CTCD6S these can come really handy in situations like that.
And how are Your 2 separate server PSUs connected together (are You using both of them?), both plugged into an extension cord or do You have some other trick for simultaneous power-on?
But if still no POST, then MB is probably bad (I tried to get mine working for almost 3 weeks, really stupid decision
. Should have just got another one and continued to mine).Thank you for your reply i already ordered your recommended device for my country. Thank you.
Ive a pico adapter but ive two psu and two pico adapter. For first start i connected 1 psu direct to the mb and only one grafic.
I tested both pico adapters for 1 PSU i thought the same maybe the pico wont work.
I tested my ram not working. I tested 2x 4GB 2133 mhs also not working. Ive a 2x 24 pin to 1 24pin adapter for connecting both psu(But for first start i didnt used it).
Everything tested on other devices.
Ive also tested to start only with on board grafic also dont work.
Ive tested diffrent risers and also direct connect to the mb also not working.
Still untested MB and CPU.
But i guess MB is gone.
Hello,
ive started today my first mining rig.
My Setup:
1x MB ASRock H110 Pro BTC+ 1151 ATX DVI DDR4 retail
1x DDR4 16GB PC 2400 CL15 G.Skill (1x16GB) 16GIS Aegis 4
1x Plus 120GB
1x Intel Pentium G4400 3300 1151 BOX*
2x Server PSU 2400 Watt
8x Vega 64
When i start the rig only fans are spinning(CPU, Graficcard) and graficcard led "Radeon" is on but no signal on my monitor.
I connected for first start:
1x 16 GB RAM DDR4 2400 mhs
2x Molex 4pin
1x 24 pin atx
1x SATA 15pin
1x 4pin CPU power (on a 8 pin slot)
1x Vega 64
Monitor is working tested on my Laptop.
Graficard fan is working and leds.
Graficcard connected both 2x 8 pin power
I tested also another graficcard same happens.
I tested diffrent risers also no signal.
Risers are powered and usb correct connected.
Ram tested on first slot and on second slot
Anyone could help me?
ive started today my first mining rig.
My Setup:
1x MB ASRock H110 Pro BTC+ 1151 ATX DVI DDR4 retail
1x DDR4 16GB PC 2400 CL15 G.Skill (1x16GB) 16GIS Aegis 4
1x Plus 120GB
1x Intel Pentium G4400 3300 1151 BOX*
2x Server PSU 2400 Watt
8x Vega 64
When i start the rig only fans are spinning(CPU, Graficcard) and graficcard led "Radeon" is on but no signal on my monitor.
I connected for first start:
1x 16 GB RAM DDR4 2400 mhs
2x Molex 4pin
1x 24 pin atx
1x SATA 15pin
1x 4pin CPU power (on a 8 pin slot)
1x Vega 64
Monitor is working tested on my Laptop.
Graficard fan is working and leds.
Graficcard connected both 2x 8 pin power
I tested also another graficcard same happens.
I tested diffrent risers also no signal.
Risers are powered and usb correct connected.
Ram tested on first slot and on second slot
Anyone could help me?
Use DDR4 2133Mhz RAM.. I guess it will work.
Mini miner could be right, thoght I have heard that MOBO in that case just clocks down Your RAM frequency to suitable one.
On paper Your CPU supported memory types are:
DDR4-1866/2133, DDR3L-1333/1600 @ 1.35V
If You have any RAM sticks with mentioned frequencies, You can give them a try.
Worth taking a look:
https://ark.intel.com/products/88179/Intel-Pentium-Processor-G4400-3M-Cache-3_30-GHz
Hello,
ive started today my first mining rig.
My Setup:
1x MB ASRock H110 Pro BTC+ 1151 ATX DVI DDR4 retail
1x DDR4 16GB PC 2400 CL15 G.Skill (1x16GB) 16GIS Aegis 4
1x Plus 120GB
1x Intel Pentium G4400 3300 1151 BOX*
2x Server PSU 2400 Watt
8x Vega 64
When i start the rig only fans are spinning(CPU, Graficcard) and graficcard led "Radeon" is on but no signal on my monitor.
I connected for first start:
1x 16 GB RAM DDR4 2400 mhs
2x Molex 4pin
1x 24 pin atx
1x SATA 15pin
1x 4pin CPU power (on a 8 pin slot)
1x Vega 64
Monitor is working tested on my Laptop.
Graficard fan is working and leds.
Graficcard connected both 2x 8 pin power
I tested also another graficcard same happens.
I tested diffrent risers also no signal.
Risers are powered and usb correct connected.
Ram tested on first slot and on second slot
Anyone could help me?
ive started today my first mining rig.
My Setup:
1x MB ASRock H110 Pro BTC+ 1151 ATX DVI DDR4 retail
1x DDR4 16GB PC 2400 CL15 G.Skill (1x16GB) 16GIS Aegis 4
1x Plus 120GB
1x Intel Pentium G4400 3300 1151 BOX*
2x Server PSU 2400 Watt
8x Vega 64
When i start the rig only fans are spinning(CPU, Graficcard) and graficcard led "Radeon" is on but no signal on my monitor.
I connected for first start:
1x 16 GB RAM DDR4 2400 mhs
2x Molex 4pin
1x 24 pin atx
1x SATA 15pin
1x 4pin CPU power (on a 8 pin slot)
1x Vega 64
Monitor is working tested on my Laptop.
Graficard fan is working and leds.
Graficcard connected both 2x 8 pin power
I tested also another graficcard same happens.
I tested diffrent risers also no signal.
Risers are powered and usb correct connected.
Ram tested on first slot and on second slot
Anyone could help me?
Use DDR4 2133Mhz RAM.. I guess it will work.
Thanks for reply.
Ive tested now other DDR4 Ram 2x 4 GB dosnt work
Now only CPU and MB left. I would say the asrock h110 is not working.
Could anyone check if my components fits together (scroll up) CPU, Ram, MB.
Ill change the MB on Monday.
Ive tested now other DDR4 Ram 2x 4 GB dosnt work
Now only CPU and MB left. I would say the asrock h110 is not working.
Could anyone check if my components fits together (scroll up) CPU, Ram, MB.
Ill change the MB on Monday.
Are You using a PICO adapter to connect Your server PSU to motherboard (maybe bad PICO)? https://www.amazon.com/Insten-24-pin-Power-Supply-Tester/dp/B005CTCD6S these can come really handy in situations like that.
And how are Your 2 separate server PSUs connected together (are You using both of them?), both plugged into an extension cord or do You have some other trick for simultaneous power-on?
But if still no POST, then MB is probably bad (I tried to get mine working for almost 3 weeks, really stupid decision
. Should have just got another one and continued to mine).
Thanks for reply.
Ive tested now other DDR4 Ram 2x 4 GB dosnt work
Now only CPU and MB left. I would say the asrock h110 is not working.
Could anyone check if my components fits together (scroll up) CPU, Ram, MB.
Ill change the MB on Monday.
Ive tested now other DDR4 Ram 2x 4 GB dosnt work
Now only CPU and MB left. I would say the asrock h110 is not working.
Could anyone check if my components fits together (scroll up) CPU, Ram, MB.
Ill change the MB on Monday.
Hi,
Had exactly the same problem with my AsRock H81 PRO BTC R2.0 board. Tried many different things, but no POST (only GPU fan working, no display).
What You could try:
Easily doable
*Take out Your CMOS battery
*Clean CMOS with onboard jumper
*Tri to boot with only one RAM in slot
*Only have CPU (and CPU cooler connected to the right place!), RAM (ONLY 1 stick), 24 PSU connector and 4(or 8 pin) CPU power connected. Use the onboard VGA output for Your monitor.
(Steps not in certain order, just some things You should try)
Still no POST?
*Try to switch Your CPU
*Try to switch Your RAM between different slots (1 by 1)
*Test Your CPU on another board
I tried all of those steps with my board and none of them worked. In my case, the MOBO was just a bad one and the more I tried to solve this problem, the more I saw how many people had exactly the same problem with the same board. The truth is that AsRock makes some nice boards but sadly it seems that a lot of them come out of the box as brand new but not working.
I used provided warranty to send my MOBO back to AsRock for repairs/brand new board. Right now I use second H81 and everything works as it should (Plug in and mine away!).
Hope everything works out for You, keep us posted!
Had exactly the same problem with my AsRock H81 PRO BTC R2.0 board. Tried many different things, but no POST (only GPU fan working, no display).
What You could try:
Easily doable
*Take out Your CMOS battery
*Clean CMOS with onboard jumper
*Tri to boot with only one RAM in slot
*Only have CPU (and CPU cooler connected to the right place!), RAM (ONLY 1 stick), 24 PSU connector and 4(or 8 pin) CPU power connected. Use the onboard VGA output for Your monitor.
(Steps not in certain order, just some things You should try)
Still no POST?
*Try to switch Your CPU
*Try to switch Your RAM between different slots (1 by 1)
*Test Your CPU on another board
I tried all of those steps with my board and none of them worked. In my case, the MOBO was just a bad one and the more I tried to solve this problem, the more I saw how many people had exactly the same problem with the same board. The truth is that AsRock makes some nice boards but sadly it seems that a lot of them come out of the box as brand new but not working.
I used provided warranty to send my MOBO back to AsRock for repairs/brand new board. Right now I use second H81 and everything works as it should (Plug in and mine away!).
Hope everything works out for You, keep us posted!
Jump to: