No.
The problem is an AUC3 dongle that was not programmed (flashed) at the factory when made. Open a ticket with Minerwarez/Canaan and they will send new ones to you.
And again - post in the Official Avalon hardware thread. This is last time I am answering here.
Topic: Avalon 741 didn't mine (Read 835 times)
If that's the case get a hold of Canaan through a support ticket, or try to find someone in your country willing to part with a working one.
Which the OP should have started right after the initial troubleshooting was done...Again, posting their trouble in the Avalon thread would have gotten them to this point much much faster... Had they bothered to read it they would have seen others that had same issue and what the cause is. I believe 1st showed up with some of the ones from huge order f*up in August when Canaan was scrambling to get as many miners made/shipped as possible.
Having same issue all green on miner everything connected green auc 3 not mining. seems like only issue is controller not communicating with miner
Anyone find any solutions besides new auc3 If that's the case get a hold of Canaan through a support ticket, or try to find someone in your country willing to part with a working one.
Which the OP should have started right after the initial troubleshooting was done...Again, posting their trouble in the Avalon thread would have gotten them to this point much much faster... Had they bothered to read it they would have seen others that had same issue and what the cause is. I believe 1st showed up with some of the ones from huge order f*up in August when Canaan was scrambling to get as many miners made/shipped as possible.
Ya REALLY should be posting this in the Official Avalon thread in Hardware... Canaan monitors it.
The green lights on the miners says they are alive but idling. Will be blue when they are mining.
Wonder if you got some of the un-flashed AUC3 dongles Canaan had a problem with...
The green lights on the miners says they are alive but idling. Will be blue when they are mining.
Wonder if you got some of the un-flashed AUC3 dongles Canaan had a problem with...
yep I think he did
I didn't realise they had become such a problem. Shitty to get 2 out of 2 bad.
If that's the case get a hold of Canaan through a support ticket, or try to find someone in your country willing to part with a working one.
Hm. I wonder if he is using the right cable on the AUC-Miner. It's not a crossover cable from Amazon by chance, is it?
could be they sell them
but bad auc 3's have been an issue the avalon thread talks about it
Hm. I wonder if he is using the right cable on the AUC-Miner. It's not a crossover cable from Amazon by chance, is it?
could be they sell them
but bad auc 3's have been an issue the avalon thread talks about it
Hm. I wonder if he is using the right cable on the AUC-Miner. It's not a crossover cable from Amazon by chance, is it?
Ya REALLY should be posting this in the Official Avalon thread in Hardware... Canaan monitors it.
The green lights on the miners says they are alive but idling. Will be blue when they are mining.
Wonder if you got some of the un-flashed AUC3 dongles Canaan had a problem with...
The green lights on the miners says they are alive but idling. Will be blue when they are mining.
Wonder if you got some of the un-flashed AUC3 dongles Canaan had a problem with...
yep I think he did
Ya REALLY should be posting this in the Official Avalon thread in Hardware... Canaan monitors it.
The green lights on the miners says they are alive but idling. Will be blue when they are mining.
Wonder if you got some of the un-flashed AUC3 dongles Canaan had a problem with...
The green lights on the miners says they are alive but idling. Will be blue when they are mining.
Wonder if you got some of the un-flashed AUC3 dongles Canaan had a problem with...
Okay have you tried just running 1 Avalon at a time from the rasp pi? Also the cable from the auc3 to the miner, are you using the left side for input?
There is a chance that the brick you are using to power the rasp pi isn't providing enough power. Using WiFi might also put extra strain on it, not sure. Are you able to try it out with an ethernet connection?
What are you using to power the rasp pi?
Hopefully we can get this sorted
There is a chance that the brick you are using to power the rasp pi isn't providing enough power. Using WiFi might also put extra strain on it, not sure. Are you able to try it out with an ethernet connection?
What are you using to power the rasp pi?
Hopefully we can get this sorted
So on the Unit themselves as I have two of them I get full green lights.
My power supplies are the following single EVGA 1300 Watt, 2 HP 750 which I split and run 3 to each side and 2 HP 1200 Watt.
All of those configurations give me solid green lights and the status light of what looks to be white.
On the AUC3 I only get green light
I can connect to the Controller and have setup the wifi, setup slushpool which shows that is is live and communicating.
I have dedicated power supplies for my Pi3's, I have two of them so this happens with either of them.
I just don't see any avalon devices in the CGMiner status.
I have also tried each them with same setup with different cables along with switching out the AUC3's.
Thanks!!
John
My power supplies are the following single EVGA 1300 Watt, 2 HP 750 which I split and run 3 to each side and 2 HP 1200 Watt.
All of those configurations give me solid green lights and the status light of what looks to be white.
On the AUC3 I only get green light
I can connect to the Controller and have setup the wifi, setup slushpool which shows that is is live and communicating.
I have dedicated power supplies for my Pi3's, I have two of them so this happens with either of them.
I just don't see any avalon devices in the CGMiner status.
I have also tried each them with same setup with different cables along with switching out the AUC3's.
Thanks!!
John
Greetings,
I am having the exact same problem and wondering if you got your issue resolved.
Thanks!!
John
I am having the exact same problem and wondering if you got your issue resolved.
Thanks!!
John
Hi John,
So what lights do you see with everything plugged in? On the miners and the auc3 converter.
Are you able to log into the cgminer interface?
How many Avalons are hooked up?
What are you using for a psu?
There's a few things it could be.
Greetings,
I am having the exact same problem and wondering if you got your issue resolved.
Thanks!!
John
I am having the exact same problem and wondering if you got your issue resolved.
Thanks!!
John
Just checking, if you use the default pools (the ckminer ones), does the unit mine? I've noticed it's exceptionally sensitive to the pool settings in the URL....
C
C
You mean this default pool: stratum+tcp://stratum80.kano.is:80?? it didn't mine if that what you meant
your miner is not connected .
so lets try this.
tell me your rasp pi 3 power brick let me have a link.
Phil,
Here you go:
This one came with the raspberry kit i bought from Amazon
https://drive.google.com/open?id=1UgucQQ7In0XByST5Spa5bk_vGEdMyf5U
https://www.amazon.com/gp/product/B06XW6VX1H/ref=oh_aui_detailpage_o02_s01?ie=UTF8&psc=1
And this is from my iphone charger
https://drive.google.com/open?id=1Gh9mt-UG7SnnkBmKk3iKAo5wiQd1mYTS
Just checking, if you use the default pools (the ckminer ones), does the unit mine? I've noticed it's exceptionally sensitive to the pool settings in the URL....
C
C
You mean this default pool: stratum+tcp://stratum80.kano.is:80?? it didn't mine if that what you meant
your miner is not connected .
so lets try this.
tell me your rasp pi 3 power brick let me have a link.
Just checking, if you use the default pools (the ckminer ones), does the unit mine? I've noticed it's exceptionally sensitive to the pool settings in the URL....
C
C
You mean this default pool: stratum+tcp://stratum80.kano.is:80?? it didn't mine if that what you meant
Just checking, if you use the default pools (the ckminer ones), does the unit mine? I've noticed it's exceptionally sensitive to the pool settings in the URL....
C
C
is there any option if avalon damage and no replacement..is it really need to order in other country. no local made and offer lowest prize. coz i starting to built a new gpu.
without a photo of your gui it is hard to know if the gear has issues or if the why you filled in the pools has an issue.
Phil, here is my minerhttps://drive.google.com/open?id=1d_82joLnB13-i6SdOsymt7UtwESbhdt4
If you look at the Avalon Device section, there is nothing shown. I changed 4 different PSU already, from 1300W to 1500W. Still nothing.
Edit: added more pictures:
https://drive.google.com/open?id=1hY-GLfB_e5oTPFviMr82EJpoO_FZPFyx
https://drive.google.com/open?id=1W8b19aJYBrZuSWFibhNUXTmU8Eg7A5-A
https://drive.google.com/open?id=1c1WH_AqjuVZIhUzGu4gWPAqEVzuXGZg2
https://drive.google.com/open?id=1ewnc5v3X1wpLdoxUl8Q2ZxjvCPNa3lEB
https://drive.google.com/open?id=1fLfeyGIMT_-jJvgummffAeFJZLrInCyd
We were going through this in one of the other threads but, we got as far as the lights all look good on his auc3 converter, and that there was power to the miners.
He quoted his psu brand and I wasn't positive but the specs looked like they might provide 650 w over more than one rail. ( I wasn't sure because I'm no expert at reading those specs... or much else lol)
I asked for a photo of his setup to make sure he plugged the connector from the auc converter to the miner properly, but it never got posted.
It's the Avalon 741 setup thread, you can find all his previous info
https://bitcointalksearch.org/topic/m.24332622
He quoted his psu brand and I wasn't positive but the specs looked like they might provide 650 w over more than one rail. ( I wasn't sure because I'm no expert at reading those specs... or much else lol)
I asked for a photo of his setup to make sure he plugged the connector from the auc converter to the miner properly, but it never got posted.
It's the Avalon 741 setup thread, you can find all his previous info
https://bitcointalksearch.org/topic/m.24332622
Jump to: