SO the videos are up.
Runs pretty quiet Phil .
Did you buy a transformer to set power to 220 vs 238-243 you normally get?
Topic: Bitmain will be releasing S15 and T15 on 8/11/2018 - page 5. (Read 31485 times)
Yes I did but slow uploading time again.
I also moved off mmpool.org a none asic boost pool pulling 1621-1625 watts
to pool.ckpool.org an asic boost pool
1547 watts same hash rate and a 75 watt savings
video is not up won't be up for a while
Your video will be live at: https://youtu.be/P8MwWwctWVw
I also moved off mmpool.org a none asic boost pool pulling 1621-1625 watts
to pool.ckpool.org an asic boost pool
1547 watts same hash rate and a 75 watt savings
video is not up won't be up for a while
Your video will be live at: https://youtu.be/P8MwWwctWVw
Did you post a newer video on youtube to show the corrected sound readings?
I must say electronics on carpet like that with the risk of static shock when touching the unit would kind of worry me. Id place an anti static mat under those personally if they had to be ran on carpet or a rug like that.
you are correct if you look at tv set shelf in the picture there is a grounding bar just at top center
I ground myself on it before I touch units.
I moved unit into garage for testing over the week end.
I did a you tube video.
it is not ready uploads are slow.
link:
Your video will be live at: https://youtu.be/auakWENgP8w
you will note unit is laying on fiberglass welding blanket in a sound proof setup for the testing it is shock protected.
Sound meter failed at end of video so I will do another one later today.
the gear works very well in garage and I certainly could run it
without pissing off my wife.
1625 watts and 27200 gh = 59.7 watts a th
so if all s15's do 1625 watts and 27.2 th
and my m10's do 2200 watts and 31.2 th
both on full speed it will be a hard call as to which to pick.
s15's cost me a lot more then m10's
maybe 1650 with trump tax. 1285 without tax
m10's are under 900 without the trump tax.
So far My math shows me the s15 has to net to 1000usd to equal an m10 at 875.00 usd
So If I expand I still favor m10's with the pricing I get.
m10 at 875 no tax
s15 at 1285 no tax
note running on mmpool there is no asdic boost
so the 1625 watts could be better on pool.ckpool.org
will make a new video on SAT testing other pool
Better safe then sorry
I must say electronics on carpet like that with the risk of static shock when touching the unit would kind of worry me. Id place an anti static mat under those personally if they had to be ran on carpet or a rug like that.
^ That's great news! 
I will preheat unit with an s7ln
Edit
Since it arrived 5 min ago ice cold.
lots of full sized shots
https://i.imgur.com/6sYcAcr.jpg
https://i.imgur.com/8i8VNfi.jpg
https://i.imgur.com/SCTAeHk.jpg
https://i.imgur.com/S9IOUFw.jpg
https://i.imgur.com/s7hQiod.jpg
https://i.imgur.com/GJD3B5t.jpg
https://i.imgur.com/G26L6zJ.jpg
https://i.imgur.com/30AzAsh.jpg
https://i.imgur.com/qY7IyxH.jpg
due to the cold weather today it arrived very chilled.
I am warming it up with s7ln heater/miner
I like to use this unit to warm and dry gear as it is very quiet and only 500 watts on the setting I use. this allows the chilled unit to dry and warm up more slowly.
Note I will rotate the s15 so that it gets 15 minutes on all six sides.
Better safe then sorry
^ That's great news!
my used s15 arrives today.
from a forum member in finland.
usps.com says out for delivery.
based on reports of a few psu's burning out I will use a regulator and keep power at 220volts vs 240 volts.
I will post a few shots later today.
from a forum member in finland.
usps.com says out for delivery.
based on reports of a few psu's burning out I will use a regulator and keep power at 220volts vs 240 volts.
I will post a few shots later today.
the s15 is still too high at 1020 is going to get taxed if shipped to usa.
so I am looking at what price if I order one from you?
the website reads 1650 solo with custom support.
does this reflect the drop to 1020? pre tax pre shipping
and the 65 dollar coupon
I am guessing no.
so I am looking at what price if I order one from you?
the website reads 1650 solo with custom support.
does this reflect the drop to 1020? pre tax pre shipping
and the 65 dollar coupon
I am guessing no.
It's all projection with our model. Most to all clients get a return of surplus funds or we eat the cost from our commission.
I just have to get the order number to and give them the coupon to apply and then it's detailed out on the final invoice.
I now have the S15 running,
and as guessed, it is a noisy beast..!
Mostly because of the psu fans.
I'll write more about it later on,
but here is a quick video for noise reference.
Video: https://mega.nz/#!U1FkXIRS!Nb_xEO8yTeAvmYCwLdrwiE1xSCCnkD4ue2t32QNA12s
and as guessed, it is a noisy beast..!
Mostly because of the psu fans.
I'll write more about it later on,
but here is a quick video for noise reference.
Video: https://mega.nz/#!U1FkXIRS!Nb_xEO8yTeAvmYCwLdrwiE1xSCCnkD4ue2t32QNA12s
that is a nasty pitch
I would hate to have 30 of them running
I now have the S15 running,
and as guessed, it is a noisy beast..!
Mostly because of the psu fans.
I'll write more about it later on,
but here is a quick video for noise reference.
Video: https://mega.nz/#!U1FkXIRS!Nb_xEO8yTeAvmYCwLdrwiE1xSCCnkD4ue2t32QNA12s
and as guessed, it is a noisy beast..!
Mostly because of the psu fans.
I'll write more about it later on,
but here is a quick video for noise reference.
Video: https://mega.nz/#!U1FkXIRS!Nb_xEO8yTeAvmYCwLdrwiE1xSCCnkD4ue2t32QNA12s
Looks like a price drop here. Coupons are still usable. If anyone here runs an order I'll give you my 2 $65 just send me your order number through us.
the s15 is still too high at 1020 is going to get taxed if shipped to usa.
so I am looking at what price if I order one from you?
the website reads 1650 solo with custom support.
does this reflect the drop to 1020? pre tax pre shipping
and the 65 dollar coupon
I am guessing no.
Looks like a price drop here. Coupons are still usable. If anyone here runs an order I'll give you my 2 $65 just send me your order number through us.
If you don't change pools 1 and 2, you will be giving money to Bitmain from time to time...
I know this and kinda left it there in the screenshot to be teaser, it rarely drops to backup pool as the screenshot shows I have mined successfully without dropping to giving charity to Bitmain. For month now. It is intentional laziness I'm rebel lol or stupid.
If you don't change pools 1 and 2, you will be giving money to Bitmain from time to time...
So my T15 goes up to 20volts.
Doing well with -20c outside and -10c unheated storage. PCB Temp 10c
Code:
2019-01-11 00:09:30 driver-btm-soc.c:4084:open_core_bm1391: Start Open Core!!
2019-01-11 00:09:38 driver-btm-soc.c:4156:open_core_bm1391: End Open Core!!
2019-01-11 00:09:38 freq_tuning.c:291:freq_tuning_get_max_freq: Max freq of tuning is 550
2019-01-11 00:09:38 driver-btm-soc.c:1382:get_eeprom_total_hash_rate: total rate = 23255
2019-01-11 00:09:38 power.c:381:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 19.30 ...
2019-01-11 00:09:38 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[24] = 19.887610
2019-01-11 00:09:38 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.000000
2019-01-11 00:09:39 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[31] = 19.770810
2019-01-11 00:09:39 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 19.887610
2019-01-11 00:11:45 freq_tuning.c:1779:freq_tuning_pre_test_for_user_mode: Pre-test: done.
2019-01-11 00:11:45 freq_tuning.c:2840:do_pre_test_for_user_mode: Pre-test cost 59s.
2019-01-11 00:11:47 power.c:439:get_chain_voltage: chain[0], voltage is: 15.99
2019-01-11 00:11:47 power.c:439:get_chain_voltage: chain[1], voltage is: 15.98
2019-01-11 00:11:48 power.c:439:get_chain_voltage: chain[2], voltage is: 15.98
2019-01-11 00:11:48 power.c:462:get_average_voltage: average voltage is: 15.98
2019-01-11 00:11:48 driver-btm-soc.c:7889:bitmain_soc_init: Init done!
Increase frequency to 500.00M
2019-01-15 00:54:02 driver-btm-soc.c:4917:increase_freq_slowly:
Increase frequency to 510.00M
2019-01-15 00:54:03 driver-btm-soc.c:5982:set_timeout: freq 510 final timeout=462
2019-01-15 00:54:04 driver-btm-soc.c:8029:re_open_core: re_open_core done!
2019-01-15 00:54:04 power.c:415:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 20.00 ...
2019-01-15 00:54:04 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:04 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.000000
2019-01-15 00:54:05 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:05 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.004410
2019-01-15 00:54:06 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:06 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.004410
2019-01-15 00:54:07 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:07 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.004410
2019-01-15 00:54:08 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:08 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.004410
2019-01-15 00:54:09 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:09 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.004410
2019-01-15 00:54:11 power.c:439:get_chain_voltage: chain[0], voltage is: 19.88
2019-01-15 00:54:11 power.c:439:get_chain_voltage: chain[1], voltage is: 19.87
2019-01-15 00:54:12 power.c:439:get_chain_voltage: chain[2], voltage is: 19.89
2019-01-15 00:54:12 power.c:462:get_average_voltage: average voltage is: 19.88
2019-01-15 00:54:12 driver-btm-soc.c:3787:check_system_work: low environment handler!
2019-01-15 00:54:12 driver-btm-soc.c:3788:check_system_work: low temperature reopen core and increase voltage 1 times!
2019-01-15 00:59:17 driver-btm-soc.c:1382:get_eeprom_total_hash_rate: total rate = 23255
2019-01-15 01:24:43 driver-btm-soc.c:3700:check_system_work: The avg rate is 23618 in 30 mins, PCB temperature between 9 ~ 40
2019-01-15 01:55:14 driver-btm-soc.c:3700:check_system_work: The avg rate is 23369 in 30 mins, PCB temperature between 9 ~ 40
2019-01-15 02:25:45 driver-btm-soc.c:3700:check_system_work: The avg rate is 23367 in 30 mins, PCB temperature between 9 ~ 40
2019-01-15 02:56:16 driver-btm-soc.c:3700:check_system_work: The avg rate is 23249 in 30 mins, PCB temperature between 9 ~ 40
2019-01-11 00:09:38 driver-btm-soc.c:4156:open_core_bm1391: End Open Core!!
2019-01-11 00:09:38 freq_tuning.c:291:freq_tuning_get_max_freq: Max freq of tuning is 550
2019-01-11 00:09:38 driver-btm-soc.c:1382:get_eeprom_total_hash_rate: total rate = 23255
2019-01-11 00:09:38 power.c:381:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 19.30 ...
2019-01-11 00:09:38 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[24] = 19.887610
2019-01-11 00:09:38 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.000000
2019-01-11 00:09:39 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[31] = 19.770810
2019-01-11 00:09:39 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 19.887610
2019-01-11 00:11:45 freq_tuning.c:1779:freq_tuning_pre_test_for_user_mode: Pre-test: done.
2019-01-11 00:11:45 freq_tuning.c:2840:do_pre_test_for_user_mode: Pre-test cost 59s.
2019-01-11 00:11:47 power.c:439:get_chain_voltage: chain[0], voltage is: 15.99
2019-01-11 00:11:47 power.c:439:get_chain_voltage: chain[1], voltage is: 15.98
2019-01-11 00:11:48 power.c:439:get_chain_voltage: chain[2], voltage is: 15.98
2019-01-11 00:11:48 power.c:462:get_average_voltage: average voltage is: 15.98
2019-01-11 00:11:48 driver-btm-soc.c:7889:bitmain_soc_init: Init done!
Increase frequency to 500.00M
2019-01-15 00:54:02 driver-btm-soc.c:4917:increase_freq_slowly:
Increase frequency to 510.00M
2019-01-15 00:54:03 driver-btm-soc.c:5982:set_timeout: freq 510 final timeout=462
2019-01-15 00:54:04 driver-btm-soc.c:8029:re_open_core: re_open_core done!
2019-01-15 00:54:04 power.c:415:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 20.00 ...
2019-01-15 00:54:04 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:04 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.000000
2019-01-15 00:54:05 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:05 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.004410
2019-01-15 00:54:06 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:06 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.004410
2019-01-15 00:54:07 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:07 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.004410
2019-01-15 00:54:08 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:08 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.004410
2019-01-15 00:54:09 power.c:198:get_power_voltage_from_iic_value: iic_index for voltage[17] = 20.004410
2019-01-15 00:54:09 power.c:229:set_iic_power_by_iic_data: now setting voltage to : 20.004410
2019-01-15 00:54:11 power.c:439:get_chain_voltage: chain[0], voltage is: 19.88
2019-01-15 00:54:11 power.c:439:get_chain_voltage: chain[1], voltage is: 19.87
2019-01-15 00:54:12 power.c:439:get_chain_voltage: chain[2], voltage is: 19.89
2019-01-15 00:54:12 power.c:462:get_average_voltage: average voltage is: 19.88
2019-01-15 00:54:12 driver-btm-soc.c:3787:check_system_work: low environment handler!
2019-01-15 00:54:12 driver-btm-soc.c:3788:check_system_work: low temperature reopen core and increase voltage 1 times!
2019-01-15 00:59:17 driver-btm-soc.c:1382:get_eeprom_total_hash_rate: total rate = 23255
2019-01-15 01:24:43 driver-btm-soc.c:3700:check_system_work: The avg rate is 23618 in 30 mins, PCB temperature between 9 ~ 40
2019-01-15 01:55:14 driver-btm-soc.c:3700:check_system_work: The avg rate is 23369 in 30 mins, PCB temperature between 9 ~ 40
2019-01-15 02:25:45 driver-btm-soc.c:3700:check_system_work: The avg rate is 23367 in 30 mins, PCB temperature between 9 ~ 40
2019-01-15 02:56:16 driver-btm-soc.c:3700:check_system_work: The avg rate is 23249 in 30 mins, PCB temperature between 9 ~ 40
Doing well with -20c outside and -10c unheated storage. PCB Temp 10c
I've always used VPN for years. Last few days Bitmain site and last couple weeks Innosilicons site wont display. I suppose privacy is becoming more and more a luxury.
Anyone using a VPN able to view bitmain site?
That is my thought as well. Doing all regulation in the PSU vs using the normal 2-stages (AC line > PSU 12v > hash boards 7 or whatever volts) certainly kicks up the efficiency. Has anyone looked to see if there is a coms cable going to the s15 PSU?
I would think that the Pangolin and Inno miners should do the same thing.
I would think that the Pangolin and Inno miners should do the same thing.
I confirm, In kernel log, I can see 16.5 Volts chain calibration also at 18 Volts.
S15 control chain voltage directly from P/S
Jump to: