Pages:
Author

Topic: Bitmain will be releasing S15 and T15 on 8/11/2018 - page 8. (Read 31497 times)

legendary
Activity: 4256
Merit: 8551
'The right to privacy matters'
did you choose full speed or low speed?

seems to me you choose full speed.

I wonder if 240 volts and low speed is safe
and 240 volts and high speed is not safe

also  does your 240 volt setup run  hot say 243 volts to 245 volts.

My home  can be 238 to 246 volts.

It could be  you drifted past 240 to 243-246 and on high speed they power down.

I wonder if they would have been fine on low speed.

So this now brings us to 5 issues for the s15's in this thread.

As of today  I think no one has said the m10 has had a fail.

I mention this  because  the t15  s15 m10 are the three best units for mining as of now.

It will be interesting to see if the t15 and s15 get better

the s9 got better.

it will be interesting to see if the m10  stays trouble free.
member
Activity: 61
Merit: 23
I’m running my T15 at 200v since Tuesday without issue. How long have you waited between trying to get it running again? The APW5’s I have, when they trip into protection mode, can take 15 minutes of being unplugged before they’ll respond to power input again. I wonder, what are the stats on the APW8?

I was thinking that too. Did try to re-power the units a couple times over the course of a few hours, but no luck. One unit was in my basement, about 60 degrees ambient and only ran for about 45 minutes. The psu on that unit was quite hot to the touch just after it lost power. The other unit was in my garage, about 35 degrees ambient. That unit ran for 11 hours before it lost power, again, the PSU was quite hot to the touch. I put a meter on both the outlets and they tested 240v. I will take both S15's back into the office Monday and put them on the rack at 208v and see if they power back up, or if something inside the PSU is actually blown. I would like to open them up and do some power troubleshooting but I don't want to void the warranty in case they need to go back. Bitmain doesn't seem to be offering any spare parts for these yet. I don't know if my experience is typical but I wanted to throw out a word of caution if anyone else is operating these at the high end of their voltage rating.
copper member
Activity: 330
Merit: 103
What input voltage are you guys running these at? The 8 S15 28Th units we've been running on our rack @ 208v since Monday are all functioning perfectly. Two units that arrived yesterday that we setup at a different location on 240v ran fine initially but both failed within 12 hours. PSU dead, no power. The card included with the units shows a rated voltage range of 200-240v.

I’m running my T15 at 200v since Tuesday without issue. How long have you waited between trying to get it running again? The APW5’s I have, when they trip into protection mode, can take 15 minutes of being unplugged before they’ll respond to power input again. I wonder, what are the stats on the APW8?
newbie
Activity: 9
Merit: 0
Anyone gotten to Overclock these babies?

got an S15 28th

firmwire 3dec 2018

seems i cannot do anything with it.

Ssh doesent work neather, thats why im wondering if anyone gotten to OC these ones or gotten any more info out of them Smiley
member
Activity: 61
Merit: 23
What input voltage are you guys running these at? The 8 S15 28Th units we've been running on our rack @ 208v since Monday are all functioning perfectly. Two units that arrived yesterday that we setup at a different location on 240v ran fine initially but both failed within 12 hours. PSU dead, no power. The card included with the units shows a rated voltage range of 200-240v.
full member
Activity: 265
Merit: 232
Seems they are selling 27 TH/s and 28 TH/s batches at different prices now. My scoring hashrate has been averaging 28-30 TH/s on Slush and sometimes spikes at 32 TH/s. No problems since turning it on.
hero member
Activity: 1610
Merit: 538
I'm in BTC XTC
Yeah, we know...  Roll Eyes

And it looks like they changed the S15 price back to 1.2k USD.  Cheesy

No coupon was sent to me.
full member
Activity: 294
Merit: 100
Dang, I knew I should had wait a bit.

I paid 1.2k USD for the S15 (27Ths  Jan. 11-->)
and now they dropped the same batch price to 1k USD.

Fuck.

Price went back to 1.2k USD
legendary
Activity: 4256
Merit: 8551
'The right to privacy matters'
For the 10 trillionth time, Socket Connect Failed IS NOT AN ERROR.

Literally all it means is cgminer is not running.

I have noticed when changing pool information on the T15 it can take another 15-20 minutes before it starts hashing again.....how long did you wait before deciding it wasnt working?

Yeah this also happens on other machine from other companies they are all running cgminer. Even 30 minutes before it connects can happen.

Some tips if it happens a lot

use good ETH cables
Make sure your switch works.
Long ETH cable runs can make it worse.

Avoid WiFi
full member
Activity: 294
Merit: 129
T15 issues. When switching pools I keep getting Socket Connect Failed.

For the 10 trillionth time, Socket Connect Failed IS NOT AN ERROR.

Literally all it means is cgminer is not running.

I have noticed when changing pool information on the T15 it can take another 15-20 minutes before it starts hashing again.....how long did you wait before deciding it wasnt working?
full member
Activity: 1022
Merit: 221
We are not retail.
Looks like it's making friends already.
copper member
Activity: 330
Merit: 103
Some pics from unboxing to setup:





hero member
Activity: 1610
Merit: 538
I'm in BTC XTC
Crap, makes the coupon moot doesn't it...  Angry

Got 'til the end of the month before it expires, guess I'll keep an eye on price and make a move if it dips again.  Wink
legendary
Activity: 2464
Merit: 1710
Electrical engineer. Mining since 2014.
And it looks like they changed the S15 price back to 1.2k USD.  Cheesy

No coupon was sent to me.
legendary
Activity: 4256
Merit: 8551
'The right to privacy matters'
So much like the early s9s there are problems.

So far 1 t15 and 2 s15 based on the threads.

Batches 1 to 6 on the s9s had trouble .

Can you. try. A different firmware?
jr. member
Activity: 34
Merit: 60
T15 issues. When switching pools I keep getting Socket Connect Failed. It takes several re-boots (quite a few sometimes) and finally connects. Annoying. Now, after less than a week, I lost a chain. So now hash is under 15TH.
full member
Activity: 1022
Merit: 221
We are not retail.
Decent Bitmain price drop ftw.
newbie
Activity: 12
Merit: 1
I had a lot of problems with the network error initially. But figured out I needed to follow the static IP setup to accept a new pool. I think it's a great machine so far. 28.5ths running full power. Over 18 in economode.
full member
Activity: 294
Merit: 129
Which FW did your T15 ship with?

Miner Type   Antminer T15
Hostname   antMiner
Model   GNU/Linux
Hardware Version   13.16394.1.3
Kernel Version   Linux 4.6.0-xilinx-gff8137b-dirty #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
File System Version   Sat Dec 29 10:39:18 CST 2018
CGminer Version   4.9.0



^^ Good to hear.
Now the question will become how many weeks/months the miners run before we start seeing issues Wink

I have been doing this for a few years now, and bitmain reliability is on par or better than any company I have worked with outside of Canaan, whose miners are never competitive anyway.
legendary
Activity: 1554
Merit: 2037
Vrobb I'm sure they're sticky on this, the largest coupon you can use for this batch of s15 is a 240$.

I only know because at that price I've been on the hunt for real, and cheap coupons.

Dang, I knew I should had wait a bit.

Damn, I hate when that happens. Email them and maybe they'll throw you a bone, probably in coupon form.
Pages:
Jump to: