Topic: Custom Innosilicon A2 Terminator image - Anx Edition (Read 22718 times)

Hi, i'm using version 09-01-2015. When i try to use extranonce, it will not connect to nicehash. Is extranonce supported by this version?

How did you manage that? Would you mind sharing. I have an A4 I'm ripping my hair out with!

Has anyone successfully migrated this awesome image to the A4 Dominator?

nvrmind.  I brushed up on my php and made the changes so I could use this badass front-end on the A4.

Just wanted to share that I was able to resurrect a dead A2 60MHs (4 mining boards) unit with this firmware.  The host died about 2 months ago and I'd basically written it off.  Pulled it apart yesterday, found that the SD card was dead.  I downloaded a couple of different images, the one referenced above, the one from zoomhash and the one from Emdje.

For no particular reason, I started with this one from MarkAz (quoted/referenced) and fired it up.  Connected to the webUI, modified the miner settings, and clicked start.  Boom, operational again.

Couple of questions/thoughts.  In the webUI, under device profile, there is a text field to input the number of boards (mine is 4), and a drop down for picking either the 88MH/s or 110MH/s models.  I don't know that it's relevant for anything other than the user interface, but if you were so inclined to update the image for the 2 and 4 board models, that wold be awesome.

At the top of the page, there appear to be a total of 8 graphs available.  The lower 4 are CPU Load, Temp, Gateway ping and Internet ping.  The top 4 are not rendering or are broken (no data?). scratch that - after about an hour, the top 4 graphs are showing now.

Anyway, I left the speed at the default of 1200Mhz, I see no reason to change it if it's working.  After about 30 minutes, the total board average is about 58MHs, which is a little slower than I remember (avg around 62).  I may grab try one of the other images and attempt a high clock speed, but I'll probably leave it alone for a bit and confirm what the pool side sees.

Feel free to ask any questions, I'm happy to share any details about the chassis or the setup.

Cheers,
baldpope

Error rate is arount 0.08%-0.21% consistently. I am not using extraonce subscription how can I enable it? I am using Anx version I don't think it supports extraonce (latest one).

Please pardon my ignorance how can i check for hardware errors?

I have all the setting on default didnot change anything yet, using webinterface just to add pool and worker information and left all the rest of the setting as is.

Please let me know if there is you would like me to try and post.  

How many hardware errors do you get? What settings do you use? Are you using extranonce subscription?

And yes, you could use a different pool, it can definitely make a difference.

Hey guys I purchased an A2 terminator 88mh/s on the webinterface using Anx version its says its hashing at 88Mh/s all 6 boards are functioning and reporting 14-15mh/s for total of 87-88mh/s however on the litecoin pool i am getting 65-68mh/s max it fluctuates pretty wildly between 60-68mh/s but averaging 66mh/s over 24hours. Let me know if i should change pool or try something different.

Any advice will be appreciated. I am using Anx latest version.

 

If anyone has any information on getting the terminator a2 mega  running in minera, it would be greatly appreciated.

Hey there,

somone can help for the new A4 14nm Dominator from Innosilicon how to access the conf. file for cgminer via rapsberry pi? Similar as from zoomhash (sudo nano .cgminer/cgminer.conf)

What is the root login for the pi? I have atm. pi/raspberry
Webinterface is not helping me to change the API listen 127.0.0.1 to loacl computer adress from miner and let me change scan/expiry settings etc.

Pls. help. I know that might be the wrong topic but help is needed.

I'm using the latest image but it's auto-rebooting every 2 minutes.

Well it is hard to say, there is really no fantastic documentation on what the LEDs mean, I have found that they tell the state of the hash chips, the on board power and other various things. So we know something is wrong , as to what going to be hard to tell.


Here would be my approach.
First thing does it get detected? I am going to guess not. Next thing would be to check the voltage regulators, I would check to see if the DC-DC converters are making voltage for all the chips, if so there is a 3.3v and a 1.8v regulator, if those are good then check to see if the 12 MHZ clock is working for the chips if so check all the logic buffers sending the signals out, if all the hash chips have the clock then check to see if you see any signal on the spi clock out to the chips if those are good, make sure there good after the 3.3 to 1.8v level shifters.

while there are some more steps to check I am going to guess this may be out of reach, while I could say I can fix that for you, it may not be fixable or might not be worth sending somewhere to fix and get it back.

I have been looking for broken boards to work on and try to repair, I have had some success with it.

Hello everyone. I have a question regarding board troubleshooting. Okay so i have an older black A2 terminator 88 and it has 6 boards. 5/6 boards have all 8 green LEDS on. The last board has 7/8 green LEDS on. I believe this 1 led that us not lit, is causing my hashing power to drop about 10 mh/s. What exactly does only having 7/8 LEDS on signify? and how might i go about fixing this problem? Thank you for your time!

You need to use the IP of the computer running the ARG wallet, not 127.0.0.1 since the A2 is not running the wallet software. Assign a static IP to the computer, via your router settings. Once that is done, type it into your A2 e.g 192.168.1.50:6624

Change rcpallowip to your A2's static ip.

Yes it is a devilcoin.conf file

I guess it's the details i am putting into my miner settings Pool 1 add settings. I am mining other coins quite happily on mining pools but would like to learn how to solo mine. I will keep reading as and when i get time.

If someone could post their details of a solo mineable coin, ie coin name, config file details, pool 1 add in the A2 software and i could test it. Cheers

Make sure it's devilcoin.conf

sometimes windows will save it as devilcoin.conf.txt

Can anyone help me with my solo mining ? Thanks

Is this image still being updated?

How much was it sold for?

ok let me know if things change.

 I have 1 failed board of 6 so it would be nice to replace that one and have 1 more on hand as a backup. There was an ebay listing for a set of 6 a few weeks ago but it's gone now.  I feel like I should have bought them..

I don't really see any issues with this, if your miner has 5 boards then I am guessing there the 12 chip blue boards. The way it stands you should be able to put 6 boards of whatever in them as long as you can handle the power requirements . If you don't have any luck with the dead boards send me a message maybe we can trouble shoot it a little better.