Topic: GekkoScience 2Pac/Compac BM1384 Stickminer Official Support Thread - page 15. (Read 177467 times)
September 03, 2018, 10:35:45 AM
If it's an altcoin, you might be better off asking in the altcoins section. This is more likely a software thing than hardware.
August 17, 2018, 10:11:42 PM
The first step is writing a driver for it.
August 11, 2018, 01:07:02 AM
More than likely, the issue is resistance internal in your hub or meter. The chips will draw the same amount of power (and therefore develop the same amount of heat) regardless of the input voltage.
August 11, 2018, 12:19:07 AM
My Gekko is not allowing 5V to come through its connector.
All the tables in the PDF guide calculate to a consistent 5V. So unless there is a way for the Gekko to pull 5V, there’s no way to clock the frequency above 225, nor turn up the vcore voltages to hit higher frequencies. And, at lower frequencies, it’s running hotter because it has to work harder to pull the load it needs.
Do you have any suggestions to adjust the Gekko so it will flow a proper 5V? I’ve checked this against my USB other devices. The USB meter is spot-on.
- Using a multi meter I've learned how to dial in the VCore voltage.
- Using a USB meter, I've learned regardless if I’m using my powered hub, direct connection USB 3.0 ports or direct connection USB 2.0 ports, the Gekko is only flowing 4.6 - 4.85V instead of 5V.
- The under volting is causing it to draw more amps to do the same work.
- Regardless if I set the vcore to 1.4 or 1.46, when I set the frequency to 250, the amp draw hits 2.5A, and either the USB system or the computer shuts it down.
All the tables in the PDF guide calculate to a consistent 5V. So unless there is a way for the Gekko to pull 5V, there’s no way to clock the frequency above 225, nor turn up the vcore voltages to hit higher frequencies. And, at lower frequencies, it’s running hotter because it has to work harder to pull the load it needs.
Do you have any suggestions to adjust the Gekko so it will flow a proper 5V? I’ve checked this against my USB other devices. The USB meter is spot-on.
August 10, 2018, 04:07:24 PM
I did some homework before I posted, and then I did more homework as I waited. Hopefully it helps someone somehow
+ 1million for that http://www.sherv.net/cm/emo/word/congrats-smiley-emoticon.gifYou are one of the few newbs here in a long long time who knows how to learn: 1st research and *then* ask questions. Most just say "give me a fish!" (a single answer). Ja, we'll give you a fish - a fish smack in the head. You asked "teach me to fish" (how does is work), lo and behold -- you get teachers.
I really try, I'm an AV installer by trade so I'm familiar with troubleshooting. If you mess with something and it stops working, try and set it back to last known good settings. If you can't, soft reset. If that doesn't work, factory reset. If you can't, call tech support and keep trying while you're on hold for 40 minutes. If no tech support, fuck with it until it works. I read through like 50 pages of this thread while I was waiting, hence the 8 updates on my original post haha
Also, update on my 2pac: I switched the to a different usb port than I was originally using before I went to bed last night and left the stick at 100MHZ at 1.32v. Checked on it before I went to work, it was down to 3.5GH/s, don't remember how many HW errors but I'd assume there were a few and it only gathered like 3,000 shares so it stopped really hashing right after I went to bed. That was about 7 hours ago now. Unplugged the stick and plugged it back in, checked volatge and it was 1.34 (didn't touch potentiometer) and restarted cgminer, been hashing 100MHZ at ~10GH/s all day but I've got about 9 HW errors...are those from getting too much power?
August 10, 2018, 03:50:24 PM
@vh and friends, you guys are amazing for what you have created here.
I really dont get the "Rough chart of power draw"-Table, especially the 300 MHz. So for 300 MHz it will take 13.98 watts and 2.80 ampere, but I can't find any hubs or whatsoever USB power supplier that goes beyond 2.5 ampere.
So what do I got wrong?
I really dont get the "Rough chart of power draw"-Table, especially the 300 MHz. So for 300 MHz it will take 13.98 watts and 2.80 ampere, but I can't find any hubs or whatsoever USB power supplier that goes beyond 2.5 ampere.
So what do I got wrong?
Nothing at all. It requires some "innovative" thinking to supply 3 amps to one of these. Can't be had out of a box (yet).
August 10, 2018, 03:40:33 PM
@vh and friends, you guys are amazing for what you have created here.
I really dont get the "Rough chart of power draw"-Table, especially the 300 MHz. So for 300 MHz it will take 13.98 watts and 2.80 ampere, but I can't find any hubs or whatsoever USB power supplier that goes beyond 2.5 ampere.
So what do I got wrong?
I really dont get the "Rough chart of power draw"-Table, especially the 300 MHz. So for 300 MHz it will take 13.98 watts and 2.80 ampere, but I can't find any hubs or whatsoever USB power supplier that goes beyond 2.5 ampere.
So what do I got wrong?
August 10, 2018, 09:48:30 AM
I did some homework before I posted, and then I did more homework as I waited. Hopefully it helps someone somehow
+ 1million for that 
You are one of the few newbs here in a long long time who knows how to learn: 1st research and *then* ask questions. Most just say "give me a fish!" (a single answer). Ja, we'll give you a fish - a fish smack in the head. You asked "teach me to fish" (how does is work), lo and behold -- you get teachers.
August 09, 2018, 10:54:43 PM
I did some homework before I posted, and then I did more homework as I waited. Hopefully it helps someone somehow
August 09, 2018, 10:43:36 PM
It was fun watching all those fresh edits pop up throughout the day.
August 09, 2018, 10:25:13 PM
Probably, yeah. You should see 11GH (WU of about 150) for every 100MHz if everything's working right.
Kk. Set to 1.31 @ 100MHz, gonna let it run overnight and while I'm at work tomorrow, will post an update then if stuff still seems off. Almost can't believe you got back to me O.o
August 09, 2018, 09:51:01 PM
Probably, yeah. You should see 11GH (WU of about 150) for every 100MHz if everything's working right.
August 09, 2018, 05:48:37 PM
Hey everybody, newby ass newbie here. Just got a 2pac, and of course I had to play around with it. At one point, I had 'er running at 30GH/s, which is amazing, but I've not achieved anything close since then. Since I hit that 30, I've played with the potentiometer a bit, and I'm reading voltages of .74 on both ASIC cores.
I guess my question is: do I add up the voltage from each core for a total of 1.48? or are both chips underpowered, thus explaining my ~6.5GH/s rate?
If it makes a difference to whoever responds, I've rotated the potentiometer screw clockwise to where the flat part is a 45-degree angle to the bottom right corner of the board, looking at it with the USB plug facing you.
/edit: Running at 100MHz, just lookin' for that ~10GH/s before I keep playing and trying to get it back up to around 15
/2nd edit: Using Biodom's picture on page 2 for reference for voltage testing
/3rd edit: Also, how do I measure vcore's voltage? Which piece is it? Is it the side of the 1st ASIC chip that reads about 2x what the chips themselves do?
/4th edit: found this, and it sounds like I've somehow managed to be giving the chips way too little power but I'm not 100% sure
/5th edit: Which pieces do I short out to "factory reset"?
/edit 6: It seems I just need to keep turning the potentiometer clockwise until it gives me that sweet, sweet 10GH/s at 100MHz <------------------------------is this correct?
/edit 7: Mining stably 17 ~17GH/s, at 200MHz so I think I got 'er worked out. It was all in this thread
/edit 8: dialed voltage in to 1.26, mining at about 8GH/s at 100MHz. Will leave at this setting until someone responds. This hashrate still seems a touch low, should i up the voltage to like 1.3?
I guess my question is: do I add up the voltage from each core for a total of 1.48? or are both chips underpowered, thus explaining my ~6.5GH/s rate?
If it makes a difference to whoever responds, I've rotated the potentiometer screw clockwise to where the flat part is a 45-degree angle to the bottom right corner of the board, looking at it with the USB plug facing you.
/edit: Running at 100MHz, just lookin' for that ~10GH/s before I keep playing and trying to get it back up to around 15
/2nd edit: Using Biodom's picture on page 2 for reference for voltage testing
/3rd edit: Also, how do I measure vcore's voltage? Which piece is it? Is it the side of the 1st ASIC chip that reads about 2x what the chips themselves do?
/4th edit: found this, and it sounds like I've somehow managed to be giving the chips way too little power but I'm not 100% sure
/5th edit: Which pieces do I short out to "factory reset"?
/edit 6: It seems I just need to keep turning the potentiometer clockwise until it gives me that sweet, sweet 10GH/s at 100MHz <------------------------------is this correct?
/edit 7: Mining stably 17 ~17GH/s, at 200MHz so I think I got 'er worked out. It was all in this thread
/edit 8: dialed voltage in to 1.26, mining at about 8GH/s at 100MHz. Will leave at this setting until someone responds. This hashrate still seems a touch low, should i up the voltage to like 1.3?
https://bitcointalksearch.org/topic/m.17678108
Picture and explanation of where to measure. You should see 1.24-1.26V across the two chips, with 620-630mV per chip. If that's the case, there's an IO line broken somewhere. If there's an imbalance causing the string to lock up, your Node 0 voltage will be about 480mV. If that's the case, turn up the voltage a bit, unplug, wait about 20 seconds and plug it back in.
Picture and explanation of where to measure. You should see 1.24-1.26V across the two chips, with 620-630mV per chip. If that's the case, there's an IO line broken somewhere. If there's an imbalance causing the string to lock up, your Node 0 voltage will be about 480mV. If that's the case, turn up the voltage a bit, unplug, wait about 20 seconds and plug it back in.
August 09, 2018, 05:44:10 AM
found solution :
cd ~/git/vthoang/cgminer/
sudo usermod -G plugdev -a `whoami`
sudo cp 01-cgminer.rules /etc/udev/rules.d/
sudo reboot
from here : https://www.eyeboot.com/download/GekkoScience_2PAC_BM1384_USB_Stick_Miner/2PAC_BM1384_USB_Setup_Guide.pdf
its written badly , so you have to tweek as all joined
it is a real shame that both bitcoin forum and bitshopper.de have inadequate instructions on both 2pac and moonlander 2. have had to find other ways to set up. sloppy work by the big guys.
cd ~/git/vthoang/cgminer/
sudo usermod -G plugdev -a `whoami`
sudo cp 01-cgminer.rules /etc/udev/rules.d/
sudo reboot
from here : https://www.eyeboot.com/download/GekkoScience_2PAC_BM1384_USB_Stick_Miner/2PAC_BM1384_USB_Setup_Guide.pdf
its written badly , so you have to tweek as all joined
it is a real shame that both bitcoin forum and bitshopper.de have inadequate instructions on both 2pac and moonlander 2. have had to find other ways to set up. sloppy work by the big guys.
Simply ask for support (Chat; E-Mail) before you complain, newbie. The topic could have been resolved within minutes.
Others would say: RTFM!!! The support thread is linked from our website and the solution is mentioned on page 1.
MacEntyre
bitshopper.de
July 31, 2018, 02:34:34 AM
The crypto space is full of morons. They don't know how to read, how to research. When they have a problem they don't try to solve it, instead they go online hoping for an answer.
July 30, 2018, 08:00:37 AM
Yeah I hear you man, if only that incredibly common problem were answered in the FAQ section of the first post.
...oh wait
Q. How to get past "USB init, open device failed" ... "you don't have privilege to access" error.
Code:
cd ~/git/vthoang/cgminer/
sudo usermod -G plugdev -a `whoami`
sudo cp 01-cgminer.rules /etc/udev/rules.d/
sudo reboot
sudo usermod -G plugdev -a `whoami`
sudo cp 01-cgminer.rules /etc/udev/rules.d/
sudo reboot
Or maybe if it was solved in the README file, like the error message specifically states the user should check?
...oh wait
Code:
LINUX:
The short version:
sudo cp 01-cgminer.rules /etc/udev/rules.d/
The long version:
On linux, the direct USB support requires no drivers at all. However due to
permissions issues, you may not be able to mine directly on the devices as a
regular user without giving the user access to the device or by mining as
root (administrator). In order to give your regular user access, you can make
him a member of the plugdev group with the following commands:
sudo usermod -G plugdev -a `whoami`
If your distribution does not have the plugdev group you can create it with:
sudo groupadd plugdev
In order for the USB devices to instantly be owned by the plugdev group and
accessible by anyone from the plugdev group you can copy the file
"01-cgminer.rules" from the cgminer archive into the /etc/udev/rules.d
directory with the following command:
sudo cp 01-cgminer.rules /etc/udev/rules.d/
After this you can either manually restart udev and re-login, or more easily
just reboot.
The short version:
sudo cp 01-cgminer.rules /etc/udev/rules.d/
The long version:
On linux, the direct USB support requires no drivers at all. However due to
permissions issues, you may not be able to mine directly on the devices as a
regular user without giving the user access to the device or by mining as
root (administrator). In order to give your regular user access, you can make
him a member of the plugdev group with the following commands:
sudo usermod -G plugdev -a `whoami`
If your distribution does not have the plugdev group you can create it with:
sudo groupadd plugdev
In order for the USB devices to instantly be owned by the plugdev group and
accessible by anyone from the plugdev group you can copy the file
"01-cgminer.rules" from the cgminer archive into the /etc/udev/rules.d
directory with the following command:
sudo cp 01-cgminer.rules /etc/udev/rules.d/
After this you can either manually restart udev and re-login, or more easily
just reboot.
Don't accuse "the big guys" of not giving you enough info. Rather, start paying attention.
July 29, 2018, 01:04:50 PM
found solution :
cd ~/git/vthoang/cgminer/
sudo usermod -G plugdev -a `whoami`
sudo cp 01-cgminer.rules /etc/udev/rules.d/
sudo reboot
from here : https://www.eyeboot.com/download/GekkoScience_2PAC_BM1384_USB_Stick_Miner/2PAC_BM1384_USB_Setup_Guide.pdf
its written badly , so you have to tweek as all joined
it is a real shame that both bitcoin forum and bitshopper.de have inadequate instructions on both 2pac and moonlander 2. have had to find other ways to set up. sloppy work by the big guys.
cd ~/git/vthoang/cgminer/
sudo usermod -G plugdev -a `whoami`
sudo cp 01-cgminer.rules /etc/udev/rules.d/
sudo reboot
from here : https://www.eyeboot.com/download/GekkoScience_2PAC_BM1384_USB_Stick_Miner/2PAC_BM1384_USB_Setup_Guide.pdf
its written badly , so you have to tweek as all joined
it is a real shame that both bitcoin forum and bitshopper.de have inadequate instructions on both 2pac and moonlander 2. have had to find other ways to set up. sloppy work by the big guys.
I get this
failed usb_init
[2018-07-29 18:08:41.621] USB init, open device failed, err -3, you don't have privilege to
access - BSC device 1:24
[2018-07-29 18:08:41.621] See README file included for help
[2018-07-29 18:08:41.622] GekkoScience detect (1:24) failed to initialise (incorrect device?
), resetting
[2018-07-29 18:08:41.622] failed usb_init
[2018-07-29 18:08:46.958] USB init, open device failed, err -3, you don't have privilege to
access - BSC device 1:24
[2018-07-29 18:08:46.959] See README file included for help
[2018-07-29 18:08:46.959] GekkoScience detect (1:24) failed to initialise (incorrect device?
)
failed usb_init
[2018-07-29 18:08:41.621] USB init, open device failed, err -3, you don't have privilege to
access - BSC device 1:24
[2018-07-29 18:08:41.621] See README file included for help
[2018-07-29 18:08:41.622] GekkoScience detect (1:24) failed to initialise (incorrect device?
), resetting
[2018-07-29 18:08:41.622] failed usb_init
[2018-07-29 18:08:46.958] USB init, open device failed, err -3, you don't have privilege to
access - BSC device 1:24
[2018-07-29 18:08:46.959] See README file included for help
[2018-07-29 18:08:46.959] GekkoScience detect (1:24) failed to initialise (incorrect device?
)
July 29, 2018, 12:10:34 PM
I get this
failed usb_init
[2018-07-29 18:08:41.621] USB init, open device failed, err -3, you don't have privilege to
access - BSC device 1:24
[2018-07-29 18:08:41.621] See README file included for help
[2018-07-29 18:08:41.622] GekkoScience detect (1:24) failed to initialise (incorrect device?
), resetting
[2018-07-29 18:08:41.622] failed usb_init
[2018-07-29 18:08:46.958] USB init, open device failed, err -3, you don't have privilege to
access - BSC device 1:24
[2018-07-29 18:08:46.959] See README file included for help
[2018-07-29 18:08:46.959] GekkoScience detect (1:24) failed to initialise (incorrect device?
), resetting
[2018-07-29 18:08:46.960] failed usb_init
I am trying to run at 150 ...
./cgminer -o stratum+tcp://pool.ckpool.org:3333 -u 3DZ3cEJYk5GUyGRJ7nkDqttUcaNgAtWais -p x --suggest-diff 32 --gekko-2pac-freq 150
failed usb_init
[2018-07-29 18:08:41.621] USB init, open device failed, err -3, you don't have privilege to
access - BSC device 1:24
[2018-07-29 18:08:41.621] See README file included for help
[2018-07-29 18:08:41.622] GekkoScience detect (1:24) failed to initialise (incorrect device?
), resetting
[2018-07-29 18:08:41.622] failed usb_init
[2018-07-29 18:08:46.958] USB init, open device failed, err -3, you don't have privilege to
access - BSC device 1:24
[2018-07-29 18:08:46.959] See README file included for help
[2018-07-29 18:08:46.959] GekkoScience detect (1:24) failed to initialise (incorrect device?
), resetting
[2018-07-29 18:08:46.960] failed usb_init
I am trying to run at 150 ...
./cgminer -o stratum+tcp://pool.ckpool.org:3333 -u 3DZ3cEJYk5GUyGRJ7nkDqttUcaNgAtWais -p x --suggest-diff 32 --gekko-2pac-freq 150
cant get this to work on raspberry pi
I follow to the letter
I get USB device fail
Debian 8.7.1 new install.
Default Install (No desktop environment, + SSH Server)
(*do not specify root password to enable sudo)
or Raspbian - Kernel version: 4.4 (Raspberry Pi)
I follow to the letter
I get USB device fail
Code:
sudo apt-get update
sudo apt-get upgrade -y
sudo apt-get install -y build-essential git autoconf automake libtool pkg-config libcurl4-openssl-dev libudev-dev
mkdir -p git/vthoang; cd git/vthoang
git clone https://github.com/vthoang/cgminer.git
cd cgminer
CFLAGS="-O2 -march=native" ./autogen.sh --enable-gekko
make -j 2
sudo apt-get upgrade -y
sudo apt-get install -y build-essential git autoconf automake libtool pkg-config libcurl4-openssl-dev libudev-dev
mkdir -p git/vthoang; cd git/vthoang
git clone https://github.com/vthoang/cgminer.git
cd cgminer
CFLAGS="-O2 -march=native" ./autogen.sh --enable-gekko
make -j 2
Debian 8.7.1 new install.
Default Install (No desktop environment, + SSH Server)
(*do not specify root password to enable sudo)
or Raspbian - Kernel version: 4.4 (Raspberry Pi)
Code:
sudo apt-get update
sudo apt-get upgrade -y
sudo apt-get install -y build-essential git libusb-1.0-0-dev libusb-1.0-0 libcurl4-openssl-dev libncurses5-dev libudev-dev screen libtool automake pkg-config libjansson-dev
mkdir -p git/vthoang; cd git/vthoang
git clone https://github.com/vthoang/cgminer.git
cd cgminer
CFLAGS="-O2" ./autogen.sh --enable-gekko
make -j 2
sudo apt-get upgrade -y
sudo apt-get install -y build-essential git libusb-1.0-0-dev libusb-1.0-0 libcurl4-openssl-dev libncurses5-dev libudev-dev screen libtool automake pkg-config libjansson-dev
mkdir -p git/vthoang; cd git/vthoang
git clone https://github.com/vthoang/cgminer.git
cd cgminer
CFLAGS="-O2" ./autogen.sh --enable-gekko
make -j 2
July 29, 2018, 11:45:02 AM
cant get this to work on raspberry pi
I follow to the letter
I get USB device fail
Debian 8.7.1 new install.
Default Install (No desktop environment, + SSH Server)
(*do not specify root password to enable sudo)
or Raspbian - Kernel version: 4.4 (Raspberry Pi)
http://23.108.83.14/images/2Pac-0002.JPG
http://23.108.83.14/images/2Pac-0003.JPG
Window cgminer.exe build steps (grab the finished zip file in the next paragraph if you want to skip this)
Linux cgminer.exe cross-compile steps (for windows use)
Ubuntu 16.04.1 LTS new install.
Default Install (+OpenSSH server)
I follow to the letter
I get USB device fail
Code:
sudo apt-get update
sudo apt-get upgrade -y
sudo apt-get install -y build-essential git autoconf automake libtool pkg-config libcurl4-openssl-dev libudev-dev
mkdir -p git/vthoang; cd git/vthoang
git clone https://github.com/vthoang/cgminer.git
cd cgminer
CFLAGS="-O2 -march=native" ./autogen.sh --enable-gekko
make -j 2
sudo apt-get upgrade -y
sudo apt-get install -y build-essential git autoconf automake libtool pkg-config libcurl4-openssl-dev libudev-dev
mkdir -p git/vthoang; cd git/vthoang
git clone https://github.com/vthoang/cgminer.git
cd cgminer
CFLAGS="-O2 -march=native" ./autogen.sh --enable-gekko
make -j 2
Debian 8.7.1 new install.
Default Install (No desktop environment, + SSH Server)
(*do not specify root password to enable sudo)
or Raspbian - Kernel version: 4.4 (Raspberry Pi)
Code:
sudo apt-get update
sudo apt-get upgrade -y
sudo apt-get install -y build-essential git libusb-1.0-0-dev libusb-1.0-0 libcurl4-openssl-dev libncurses5-dev libudev-dev screen libtool automake pkg-config libjansson-dev
mkdir -p git/vthoang; cd git/vthoang
git clone https://github.com/vthoang/cgminer.git
cd cgminer
CFLAGS="-O2" ./autogen.sh --enable-gekko
make -j 2
sudo apt-get upgrade -y
sudo apt-get install -y build-essential git libusb-1.0-0-dev libusb-1.0-0 libcurl4-openssl-dev libncurses5-dev libudev-dev screen libtool automake pkg-config libjansson-dev
mkdir -p git/vthoang; cd git/vthoang
git clone https://github.com/vthoang/cgminer.git
cd cgminer
CFLAGS="-O2" ./autogen.sh --enable-gekko
make -j 2
http://23.108.83.14/images/2Pac-0002.JPG
http://23.108.83.14/images/2Pac-0003.JPG
Window cgminer.exe build steps (grab the finished zip file in the next paragraph if you want to skip this)
Linux cgminer.exe cross-compile steps (for windows use)
Ubuntu 16.04.1 LTS new install.
Default Install (+OpenSSH server)
Code:
sudo apt-get update
sudo apt-get upgrade -y
sudo apt-get install -y build-essential git autoconf autopoint bison flex gperf libtool libtool-bin python ruby scons unzip intltool p7zip-full libgtk2.0-dev
sudo apt-get upgrade -y
sudo apt-get install -y build-essential git autoconf autopoint bison flex gperf libtool libtool-bin python ruby scons unzip intltool p7zip-full libgtk2.0-dev
July 29, 2018, 08:07:05 AM
300ghz, or 300GH/s? Because there's a big difference between those two and one of them shouldn't be possible without having broken cgminer first.
I'm guessing the white light stays lit on that stick. This generally means one of the ASICs has died and you should seek warranty replacement (assuming it's not the result of abuse).
I'm guessing the white light stays lit on that stick. This generally means one of the ASICs has died and you should seek warranty replacement (assuming it's not the result of abuse).
Jump to: