GMiner v3.24 Ergo+KASPA+ZIL/KAWPOW/Equihash/Cortex - page 122.

minertalk

jr. member

Activity: 38

Merit: 6

Quote from: logitech69 on January 08, 2019, 05:31:27 AM

Confirmed to be working flawlessly mining BEAM 150,5 with GTX 1070 @ 12-13sol/s Grin

For reference, I was getting 8.5-9sol/s with the official BEAM miner v9.0

Overclock settings with MSI Afterburner for the GTX 1070:
Power Limit: 75
Temp Limit: 72
Core Clock: +75
Memory: +500
Fan: 70%

Proof:

Thank you for your work, keep it up!

75% is too much power
asus 1070ti here power 50% core +240 memory +700

beam-cuda-miner-1.0.0.82 9-10sols/
Gminer 13sol/s but 2% go to dev and is not open source so can be more than 2%

Code:

15:03:25 Share Accepted
15:03:47 Temperature: GPU0 47C
15:03:47 Speed: GPU0 13 Sol/s
15:03:47 Power: GPU0 88W 0.15 Sol/W
15:03:47 Total Speed: 13 Sol/s Shares Accepted: 24 Rejected: 0 Power: 88W 0.15 Sol/W
15:03:47 Uptime: 0d 00:03:00 Electricity: 0.004kWh
15:04:01 Share Accepted
15:04:02 Share Accepted
15:04:05 Share Accepted
15:04:17 Temperature: GPU0 47C
15:04:17 Speed: GPU0 14 Sol/s
15:04:17 Power: GPU0 88W 0.16 Sol/W
15:04:17 Total Speed: 14 Sol/s Shares Accepted: 27 Rejected: 0 Power: 88W 0.16 Sol/W
15:04:17 Uptime: 0d 00:03:30 Electricity: 0.005kWh
15:04:21 Share Accepted
15:04:28 Share Accepted
15:04:29 Share Accepted
15:04:30 Share Accepted
15:04:32 New Job: 6
15:04:39 Share Accepted
15:04:40 New Job: 7
15:04:44 Share Accepted
15:04:47 Temperature: GPU0 47C
15:04:47 Speed: GPU0 13 Sol/s
15:04:47 Power: GPU0 88W 0.15 Sol/W
15:04:47 Total Speed: 13 Sol/s Shares Accepted: 33 Rejected: 0 Power: 88W 0.15 Sol/W
15:04:47 Uptime: 0d 00:04:00 Electricity: 0.006kWh
15:04:48 Share Accepted
15:04:49 Share Accepted
15:05:03 Share Accepted
15:05:05 New Job: 8
15:05:08 Share Accepted
15:05:08 Share Accepted
15:05:10 New Job: 9
15:05:17 Temperature: GPU0 47C
15:05:17 Speed: GPU0 13 Sol/s
15:05:17 Power: GPU0 88W 0.15 Sol/W
15:05:17 Total Speed: 13 Sol/s Shares Accepted: 38 Rejected: 0 Power: 88W 0.15 Sol/W
15:05:17 Uptime: 0d 00:04:30 Electricity: 0.007kWh

melpheos

jr. member

Activity: 557

Merit: 5

Quote from: evlo on January 08, 2019, 06:09:10 AM

Interesting, I thought you can't go under 650mV

Requesting the info will always give you a minimum of 650mV but the voltage can go as low as 450mV but with settings lower than 630mV, the performance w/s doesn't increase with any algorithm I have tested so far (and you have to overclock the CPU so much, it become the limiting factor because of instability)

Those are the voltagepoint for a 1070ti (probably the same for other 10* serie) but for some reason you can still use in between values
nvidiaInspector.exe "-setVoltagePoints:0,450000;400000|462500;400000|475000;400000|481250;400000|493750;400000|500000;400000|512500;400000|525000;400000|531250;400000|543750;
400000|550000;400000|562500;400000|575000;400000|581250;400000|593750;400000|600000;400000|612500;400000|625000;400000|631250;400000|643750;400000|650000;400000|662500;
400000|675000;400000|681250;400000|693750;400000|700000;400000|712500;400000|725000;400000|731250;400000|743750;400000|750000;400000|762500;400000|775000;400000|781250;
400000|793750;400000|800000;400000|812500;400000|825000;400000|831250;400000|843750;400000|850000;400000|862500;400000|875000;400000|881250;400000|893750;400000|900000;
400000|912500;400000|925000;400000|931250;400000|943750;400000|950000;400000|962500;400000|975000;400000|981250;400000|993750;400000|1000000;400000|1012500;400000|1025000;
400000|1031250;400000|1043750;400000|1050000;400000|1062500;400000|1075000;400000|1081250;400000|1093750;400000|1100000;400000|1112500;400000|1125000;400000|1131250;
400000|1143750;400000|1150000;400000|1162500;400000|1175000;400000|1181250;400000|1193750;400000|1200000;400000|1212500;400000|1225000;400000|1231250;400000|1243750;400000|"

hashestohashes

newbie

Activity: 63

Merit: 0

Quote from: nicklittle430 on December 15, 2018, 03:34:14 AM

I can get this miner working directly to a pool. however, MiningRigRentals will not connect.

Any ideas as to why?

this in the consol:

""02:21:47 Connected to us-east01.miningrigrentals.com:3333
02:21:47 Subscribed to Stratum Server
02:21:47 Set Nonce: f800002e
02:21:47 Authorized on Stratum Server
02:21:47 Connection Error: End of file
02:21:52 Connected to us-east01.miningrigrentals.com:3333
02:21:52 Subscribed to Stratum Server
02:21:52 Set Nonce: f800002e
02:21:52 Authorized on Stratum Server
02:21:52 Connection Error: End of file
02:21:52 All user mining pools are unavailable
02:21:53 Miner terminated, watchdog will restart process after 10 seconds""

Having the same issue but I am trying to connect directly to pools, I had the same issue with Bminer.

evlo

jr. member

Activity: 155

Merit: 4

Interesting, I thought you can't go under 650mV

melpheos

jr. member

Activity: 557

Merit: 5

Quote from: ElCryptoDinero on January 07, 2019, 08:47:19 PM

Quote from: melpheos on January 07, 2019, 06:29:49 PM

Getting

Code:

23:27:23 Total Speed: 70 Sol/s Shares Accepted: 110 Rejected: 0 Power: 381W 0.18 Sol/W

6*1070ti, nice improvement if the figures are the same on the pool side. I have to wait one hour or so to confirm

Edit : figures confirmed on pool side, getting around 290 sol/s at pool side with 4*6*1070ti

Those are some really good numbers. What are you overclocking with?

Using nvinspector to reduce voltage down to 0.6375
I have posted this kind of info here and there on the forum

logitech69

newbie

Activity: 10

Merit: 0

Confirmed to be working flawlessly mining BEAM 150,5 with GTX 1070 @ 12-13sol/s Grin

For reference, I was getting 8.5-9sol/s with the official BEAM miner v9.0

Overclock settings with MSI Afterburner for the GTX 1070:
Power Limit: 75
Temp Limit: 72
Core Clock: +75
Memory: +500
Fan: 70%

Proof: https://imgur.com/2XC2C91

Thank you for your work, keep it up!

niooron

full member

Activity: 193

Merit: 100

Miner exits with no error when run inside a nvidia-docker, with the nvidia/cuda image.

Zminer777

member

Activity: 488

Merit: 37

Quote from: oldgpuminer on January 07, 2019, 11:10:34 PM

Using

Code:

--pers BEAM

for the new algo? Or is it not needed?

Not needed. Btw personalization string for beam is “Beam-PoW”

oldgpuminer

newbie

Activity: 6

Merit: 0

Using

Code:

--pers BEAM

for the new algo? Or is it not needed?

FFI2013

hero member

Activity: 906

Merit: 507

Does anyone have any figures for around about what you should make for appropriate hashrate mining beam I no its early just wondering app numbers

ElCryptoDinero

newbie

Activity: 4

Merit: 0

Quote from: melpheos on January 07, 2019, 06:29:49 PM

Getting

Code:

23:27:23 Total Speed: 70 Sol/s Shares Accepted: 110 Rejected: 0 Power: 381W 0.18 Sol/W

6*1070ti, nice improvement if the figures are the same on the pool side. I have to wait one hour or so to confirm

Edit : figures confirmed on pool side, getting around 290 sol/s at pool side with 4*6*1070ti

Those are some really good numbers. What are you overclocking with?

cryptolad

newbie

Activity: 131

Merit: 0

Quote from: cryptolad on January 07, 2019, 08:01:54 PM

How do I access the telemetry screen from browser? tia

'

figured it out... specify api port in command line

--api xxx

the from browser...

localhost:xxx

onopko9320

full member

Activity: 216

Merit: 100

Miner on nvidia

Quote from: sedou on January 07, 2019, 07:10:53 PM

Any plans on 1060 3gb support for 150,5?

This algo use 4300mb on GPU. Its imbossible.

cryptolad

newbie

Activity: 131

Merit: 0

How do I access the telemetry screen from browser? tia

cryptolad

newbie

Activity: 131

Merit: 0

Quote from: ElCryptoDinero on January 07, 2019, 02:43:49 PM

Numbers look good for 150,5!
Did some testing with my TitanXPs.

OC = 70% +220core + 600mem
Hash = ~24 sol/s @ ~167w = 0.14 sol/w

That's great. Have no idea how to OC my Zotacs and EVGAs for this -- 1080ti/1080/1060

Any general guidance appreciated!

sedou

newbie

Activity: 224

Merit: 0

Any plans on 1060 3gb support for 150,5?

melpheos

jr. member

Activity: 557

Merit: 5

Getting

Code:

23:27:23 Total Speed: 70 Sol/s Shares Accepted: 110 Rejected: 0 Power: 381W 0.18 Sol/W

6*1070ti, nice improvement if the figures are the same on the pool side. I have to wait one hour or so to confirm

Edit : figures confirmed on pool side, getting around 290 sol/s at pool side with 4*6*1070ti

Zminer777

member

Activity: 488

Merit: 37

Quote from: winklebingkle on January 07, 2019, 03:13:21 PM

What does the bat look like to mine beam for solo miners? Do we use --pass for the api key? When I try to start the miner, it just crashes.

use --user to pass api key.

Code:

miner.exe --algo 150_5 --server beam.sparkpool.com --port 2222 --ssl 1 --user API_KEY

winklebingkle

newbie

Activity: 4

Merit: 0

What does the bat look like to mine beam for solo miners? Do we use --pass for the api key? When I try to start the miner, it just crashes.

Zminer777

member

Activity: 488

Merit: 37

Quote from: ElCryptoDinero on January 07, 2019, 02:55:12 PM

There is a problem with the GPU ordering. I targeted my 1080s based on the ordering defined by the software when launching the miner but when comparing the readings to my overclocker, it is running other cards and not the specific cards defined.

*edit - my rig might have dropped a card, restarting to test again.

GMiner order cards by PCI bus id, it should be same order as in nvidia-smi

Topic: GMiner v3.24 Ergo+KASPA+ZIL/KAWPOW/Equihash/Cortex - page 122. (Read 306623 times)