hello everyone,
for the compacf gekko science the frequency for me is 480 MH/z (originally 460 on the cgminer 4.12.1 software)
your gekko-compacf-freq 380.
my setting is 480 already increased to 500. depending on the key model it is necessary to mount in steps of 5 MH/z until it becomes unstable or the frequency is placed on a frequency below what was set.
https://www.talkimg.com/images/2024/02/02/klp7D.jpeg
https://www.talkimg.com/images/2024/02/02/kllMw.jpeg
my parameter on picture.
on the other hand, the higher the frequency, the more ventilation is required (it heats up enormously at more than 500 MH/z)
the higher the frequency, the more Current is required on the USB part (example for 460 1.6 to 1.8 A on 5.2 V // for 480 2 to 2.2 A on 5.2 V //
for the max (350 gh/s you need 5 A per USB port)
be careful not all usb hubs provide this Amperage (my usb hub blocks at 2.4 A under 5.2 V) my usb hub is powered by 12 V for 10 A (120 W)
Thank you, I will experiment based on these.for the compacf gekko science the frequency for me is 480 MH/z (originally 460 on the cgminer 4.12.1 software)
your gekko-compacf-freq 380.
my setting is 480 already increased to 500. depending on the key model it is necessary to mount in steps of 5 MH/z until it becomes unstable or the frequency is placed on a frequency below what was set.
https://www.talkimg.com/images/2024/02/02/klp7D.jpeg
https://www.talkimg.com/images/2024/02/02/kllMw.jpeg
my parameter on picture.
on the other hand, the higher the frequency, the more ventilation is required (it heats up enormously at more than 500 MH/z)
the higher the frequency, the more Current is required on the USB part (example for 460 1.6 to 1.8 A on 5.2 V // for 480 2 to 2.2 A on 5.2 V //
for the max (350 gh/s you need 5 A per USB port)
be careful not all usb hubs provide this Amperage (my usb hub blocks at 2.4 A under 5.2 V) my usb hub is powered by 12 V for 10 A (120 W)
Code:
[Unit]
Description=runs cgminer
After=network-online.target
[Service]
Type=simple
Restart=always
ExecStart=/home/rpi4/cgminer/cgminer --syslog --real-quiet -o stratum+tcp://solo.ckpool.org:3333 -u bc1qeuupt2tgerfum8jclt8aklu9cdmzzkwml9lg7c.mustafatufan_1 -p x --gekko-compacf-freq 460 --gekko-mine2 --gekko-start-freq 320 --gekko-tune-up 85 --gekko-tune2 60
[Install]
WantedBy=multi-user.target
Everything is same but with increased gekko-compacf-freq to 460, now it goes close to 300G, seems working. Thank you. I will try higher values after I make sure I have correct electrical setup. Description=runs cgminer
After=network-online.target
[Service]
Type=simple
Restart=always
ExecStart=/home/rpi4/cgminer/cgminer --syslog --real-quiet -o stratum+tcp://solo.ckpool.org:3333 -u bc1qeuupt2tgerfum8jclt8aklu9cdmzzkwml9lg7c.mustafatufan_1 -p x --gekko-compacf-freq 460 --gekko-mine2 --gekko-start-freq 320 --gekko-tune-up 85 --gekko-tune2 60
[Install]
WantedBy=multi-user.target
: 35S3SiSQ2cBhQvTn23BXcUq1WhUq5JVnTk
