Topic: Need a fan for Sapphire 5830 (Read 5910 times)

I've done this, but it only works for about a week then you have to relube it again, its a pain in the ass.  Easier to just pop the cover off and ziptie a 80mm fan onto it.

I've yet to find the four post unit(s) with those dimensions.  Still looking.

I would like to purchase two of these fans, also.

The picture above has been edited with measurements for the 4 mounting holes.  40mm along the outside edge; 57 through the middle. (Measuring from middle of hole to middle of hole).

Annoying, right? The 4 mounting posts?  I'll try to find a ruler at the office tomorrow and I'll repost here with measurements.

Not a huge issue right now, as I've got a regular old 80mm case fan zip tied to it and underclocked (& undervolted) it inside in a case, and it's doing... alright.  190 ish Mhs at 69C.

I think it's pretty rare to find someone that would watercool a 5830, as that is a huge waste. And even then, I think people usually keep the stock air coolers around just for backup in case they want to revert back to air cooling or in case something is wrong with the loop.

No worries, thanks for posting the pic.  I haven't seen many 4 legged ones in my travels.  I'll do some digging and get back to you.

Edit:  Could you measure the hole spacing (in mm)?

"First D" FD9225U12S
0.48 Amp, 12v. 

Here's a sketched up photo, sorry for the blurry-iphone-closeup-picture-crappiness.  And the toddler level red-crayon markup.

http://dl.dropbox.com/u/32375118/Fan_FD9225U12s-ScaledDown.JPG

https://bitcointalksearch.org/topic/cheap-chinese-vga-coolers-ftw-70043

I took some pictures of what mine looks like and how I took it apart

In the fourth picture, it's kind of hard to see but I have 2 screwdrivers inserted parallel to each other. I then slid one of them around and when I did that it popped the motor shaft out of the commutator.

They simply do nt want to come off. I tried inserting metal rods in 3 equidistant spots between the mounting plastic and the PCB (these 2 things are linked together) so I have a means to apply equal force when prying the fan itself away from the electrical part and the spindle inside without tearing up my hands from the mounting plastic.

I even tried prying between the pcb and the fan itself, and it threatens to break the solder points from the copper coil inside the fan, or break the PCB itself.

Maybe you are lucky and have "compatible" fans that are meant to come apart. All I know is my fans won't ever come apart like you describe intact. I even tried one of the youtube videos where a guy takes apart a blower-type vga fan in the way that you described, but it's just LOCKED in place, as if there are 1-way teeth inside that will let you insert the fan, but not take it apart.

edit: I was right. I destroyed another fan to the point that I could use pliers to get a firm grip of the pcb-like area and finally seperate the fan from the electrical part with a TREMENDOUS amount of force. The metal rod inside the fan had a cut/depressed area and the electrical part had these teeth (which I broke after successfully prying apart) that sits in this depressed area and normally prevents one from prying the fan away from the electical area.

If one of you can post the part number of the fan I'll see if I can dig them up for you, I replaced a couple a few months back and they ended up being ~8$ each, but could have been cheaper since I paid a premium to a middleman.

Shrugs. You must be prying wrong. The parts I pried apart were pretty solid and were in no danger of breaking.

Yeah.... no. I tried this for THREE fans, and I obliterated all of them (The plastic part behind the fan would always break, rendering it impossible to remount the fan ever again)

Thats why i buy org AMD Design Cards, spare parts are easy to get.

What you're suggesting is basically to relubricate the fan motor. You can actually pull the fan hub (basically it's a giant magnet) from the stationary part. Just insert 2 or 3 screwdrivers and pry. That's what I did. In my case I think I had some coils burnt out (no idea why....), which is why the grease didn't help.

Sry guys I can't get original sapphire fans atm 

They seem to have disappeared from the market along with ok priced heatsink+fan combos.

I remember reading somewhere on these forums that if you drill a small hole on the face of the fan about half a centimeter offset from the center and insert oil in there (wd-40 will work, but not as long. I have 3-in-1 oil and works great, wont evaporate), it'll release the friction and the fan will spin like brand new.

I did it for this card and it worked great. Before it would spin maybe only 60rpm. Now it spins nice n fast, and even wooshes at higher RPM.
http://www.ebay.com/itm/221020808125

I have that exact card with a seized up fan too!

I tried some lithium grease but it didnt help, so I did this:

guys let me know as i got one dead fan already but i haven't removed the plastic casing of it... but i didn't want to spend like $50 on aftermarket coolers... is it worth it?