Topic: Official Avalon Technical Support Thread - page 13. (Read 48888 times)
have you selected static ip? or unmanaged?
I changed the ivp4 to 192.168.1.170, disabled dchp and tried plugging it into an ethernet port. I can't find it anywhere under my router. All my other computers are listed. I tried the failsafe mode but when I go to 192.168.1.1 I enter my home router settings. Thanks for any help.
192.168.1.1 is your gateway so you are supposed to get the router if you enter that in. Did you enter 192.168.1.170 into the browser? That is the Avalon.
I think you didn't change the gateway on the Avalon. That should have been changed to 192.168.1.1. 192.168.1.170 is the IP, and 255.255.255.0 is the subnet mask. 192.168.1.1 would be the gateway.
If that does not work you should be able to connect by connecting an Ethernet from your computer or laptop directly into the Avalon. The IP address of your computer or laptop should be 192.168.1.xxx (anything except 1 or 170) and put in 192.168.1.170 into the browser.
Just tried that and I get could not connect webpage. I usually could look in my router and see the ip adresses of devices. For some reason this one isnt shiwing up.
Any ideas?
I changed the ivp4 to 192.168.1.170, disabled dchp and tried plugging it into an ethernet port. I can't find it anywhere under my router. All my other computers are listed. I tried the failsafe mode but when I go to 192.168.1.1 I enter my home router settings. Thanks for any help.
Is there any way to reset the settings. I tried the link above and it didnt reset it.
open the cover, connect a USB cable to the controller board and mine with a computer directly
Received my avalon today and followed the instruction to use an ethernet cable and now I cant access my avalon anymore. Any help would be appreciated.
Offering .5 bitcoin tip.
Any help would be appreciated.
PSJW4450: did you connect the Avalon to your WiFi? what happens when you access 192.168.0.100?
Originally I logged in fine turned off the wifi setting as instructed in the directions on the wiki and now I cant login. An ip doesnt show up under my router either. I can't access the 192.168.0.100 anymore.
Received my avalon today and followed the instruction to use an ethernet cable and now I cant access my avalon anymore. Any help would be appreciated.
Hey,
you can get it into the fail safe mode like this:
https://bitcointalksearch.org/topic/m.2132938
and restore the initial network setup
You can connect via ethernet and via wifi, why don't you try both?
Wifi has dhcpd by default.... you just need to figure out what IP's your access point is handing out (but nmap can be your friend ;-)
Received my avalon today and followed the instruction to use an ethernet cable and now I cant access my avalon anymore. Any help would be appreciated.
Offering .5 bitcoin tip.
Any help would be appreciated.
PSJW4450: did you connect the Avalon to your WiFi? what happens when you access 192.168.0.100?
Received my avalon today and followed the instruction to use an ethernet cable and now I cant access my avalon anymore. Any help would be appreciated.
Offering .5 bitcoin tip.
Any help would be appreciated.
Received my avalon today and followed the instruction to use an ethernet cable and now I cant access my avalon anymore. Any help would be appreciated.
Offering .5 bitcoin tip.
Received my avalon today and followed the instruction to use an ethernet cable and now I cant access my avalon anymore. Any help would be appreciated.
Offering .5 bitcoin tip.
Yo, looks like you can all chill: https://bitcointalksearch.org/topic/m.2524247 
Received my avalon today and followed the instruction to use an ethernet cable and now I cant access my avalon anymore. Any help would be appreciated.
The cooling of the current units (batch #1/#2) is not optimal ..
just a thought:why not arrange Avalon vertical with air sucking from ground and blowing to top?
stack-effect..
The reason for this is that the heavy boards (about 10 lbs each) are only fixed with small screws to the bottom of the case.
The cooling of the current units (batch #1/#2) is not optimal ..
just a thought:why not arrange Avalon vertical with air sucking from ground and blowing to top?
stack-effect..
The cooling of the current units (batch #1/#2) is not optimal ..
just a thought:why not arrange Avalon vertical with air sucking from ground and blowing to top?
stack-effect..
Question: Is 300MHz the maximum clock speed for avalon or is there a way to try to see if higher clock speeds work?
I think as always it is only a question of cooling or?The cooling of the current units (batch #1/#2) is not optimal .. for e. g. no thermal paste applied to the chips.
one4many
Question: Is 300MHz the maximum clock speed for avalon or is there a way to try to see if higher clock speeds work?
I think as always it is only a question of cooling or? 
Question: Is 300MHz the maximum clock speed for avalon or is there a way to try to see if higher clock speeds work?
Jump to: