Hey, ty for adding teamviewer to nvOC!
But i got a problem: teamviewer never start on boot, i always need to enter this on guake terminal :
sudo teamviewer --daemon enable
My rigs are not at home, and if i need to reboot this, i can't control after the reboot :-(, please help me.
Topic: [OS] nvOC easy-to-use Linux Nvidia Mining - page 297. (Read 418257 times)
I have to make a ext4 and swap partitions and set "/" to path for ext4
What sizes should the drives be?
After that I use Raw Harddisk Copy to copy the nvOC img to the ext4 partition.
Is that it? Do I have to make bootmanager or what it's called?
What sizes should the drives be?
After that I use Raw Harddisk Copy to copy the nvOC img to the ext4 partition.
Is that it? Do I have to make bootmanager or what it's called?
You don't need all that: the nvOC img file is already a full partitioned image, including the bootloader; you just need to use HDDRawCopy, as instructed in the OP, to flash it in your USB stick. Don't need to do anything else, after a successful flash it should boot right away.
Ok I was able to root and pull the current specs of my cards.
This is an 4x Gigabyte gtx 10606gb rig.
I have my MC set to 1050 in 1bash and if I'm reading this right it says I'm at a current clock of 8748 with a max of 8754.
How do I get more than a 750 MC increase?
https://i.imgur.com/Fh5XRQ4.png
This is an 4x Gigabyte gtx 10606gb rig.
I have my MC set to 1050 in 1bash and if I'm reading this right it says I'm at a current clock of 8748 with a max of 8754.
How do I get more than a 750 MC increase?
https://i.imgur.com/Fh5XRQ4.png
If u want to mine SIGT u have to lower your MemTransferRate and up your nvclock
http://imgur.com/a/yZuOE
Be in root and
nvidia-settings -a /GPUGraphicsClockOffset[3]=value
nvidia-settings -a /GPUMemoryTransferRateOffset[3]=value
U can specify by GPU, like the other command
nvidia-settings -a [gpu:0]/GPUGraphicsClockOffset[3]=value
nvidia-settings -a [gpu:0]/GPUMemoryTransferRateOffset[3]=value
I am mining Eth
Is this what I need to do to get my cards on performance level 3?
I currently have in 1bash
CC=0
MC=950
But it doesn't appear to go past a MC of 750, in the Nvidia xserver it shows level 2 as highlighted and level 0,1,3 as greyed out and level 3 shows the clock that I have set in 1bash.
Also something else I noticed this morning
I have the powerlimit set to 75w right now in1bash.
When I start up everything runs smoothly for about 15 minutes, then one of my cards changes from a PL of 75 up to 125 and my MH/s drops from 161 down to 142.
I tested the rig with the card disconnected and it still has a 15-20 MH/s drop after about 15 minutes.
https://i.imgur.com/wJzXKVI.png
https://i.imgur.com/ra5iFQO.png
https://i.imgur.com/jy0ahPp.png
https://i.imgur.com/xZEtjTS.png
Hi guys,
Installed 12 p106-100 mining cards into the ASrock h110 , when I boot with claymore the mining starts and then freezes withing couple of minutes with error 15 saying that it can't get any temperature info. I've updated the 1bash and the files in the first post but it doesn't seem to be working for some reason... I tried to change the miner to genoil and it mines for 10-15 minutes and then freezes the system as well .
Has anyone seen this before or maybe can advise on how to get rid of this error?
Installed 12 p106-100 mining cards into the ASrock h110 , when I boot with claymore the mining starts and then freezes withing couple of minutes with error 15 saying that it can't get any temperature info. I've updated the 1bash and the files in the first post but it doesn't seem to be working for some reason... I tried to change the miner to genoil and it mines for 10-15 minutes and then freezes the system as well .
Has anyone seen this before or maybe can advise on how to get rid of this error?
Hey all. I decided to give nvOC a go, but I'm kinda new to Linux so have a few questions.
I have to make a ext4 and swap partitions and set "/" to path for ext4
What sizes should the drives be?
After that I use Raw Harddisk Copy to copy the nvOC img to the ext4 partition.
Is that it? Do I have to make bootmanager or what it's called?
Thank you in advance
I have to make a ext4 and swap partitions and set "/" to path for ext4
What sizes should the drives be?
After that I use Raw Harddisk Copy to copy the nvOC img to the ext4 partition.
Is that it? Do I have to make bootmanager or what it's called?
Thank you in advance
I've managed to make it work with my RIG, it seems working fine (issue was with path as mentioned in one of the replies).
Getting around 125 MH with my 8x 1060 6GB ASUS (oc:0,mc:0,pl:80), please share you OC settings if you think I'm getting low hashrate.
Thanks.
I dont know about 1060, but on skunk algo, u dont care about mc so put them in lower value, max as u can for 1070 is -2000.
Up your powerlimit to the default powerlimit and Clockmemory step by step start at 100, wait 24h and increment by 10 after every 24hours before crash.
When crash occur reduce to the previous step, wait again more 24h if stable lower your powerlimit to get a better ratio watt / hashrate.
So for my ASUS 1070 GTX 8OG
MemClock : -2000
CoreClock : 130 ( the 24hours step, i go push to 130 just now )
PowerLimit : 150W per gpu
TempLimit : 70c
Fan range : 95-75 ( autotemp ON )
As SIGT is running good for 2500 blocks after reward get halved, i suggest you to get a stable setting cause watchdog is disable, so if your RIG crash, he dont gona reboot him self
Thanks mate for the suggestions and sharing your OC settings, i will try to increase as per your suggestions and see how it goes.
Will share my OC settings if it improves.
Hi guys,
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
SECOND STEP EDIT BASH
### Open 1bash
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
Quote
cd /home/m1/
### Create a directory for your new miner ###Quote
mkdir PMccminer
### Go in new dir ###Quote
cd PMccminer/
### Download miner client ### Quote
### Extract the file ###Quote
tar -zxvf palginmod_1.1_Ubuntu.tar.gz
### Delete start.sh ###Quote
rm start.sh
### Back to home dir ###Quote
cd /home/m1/
SECOND STEP EDIT BASH
### Open 1bash
Quote
nano 1bash
### Add SIGT and SIGT_BTC to the coin selection Quote
# CHOOSE COIN FROM:
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
Quote
SIGT_WORKER="SIGT"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
Quote
BTC_ADDRESS="3JJaMUVBJp55BNsGvYynaJhDXRyUf95hyG"
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
Quote
if [ $COIN == "SIGT_BTC" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Quote
IAmNotAJeep_and_Maxximus007_WATCHDOG="NO"
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
I've tried with my 1060 6G rig, it failed saying can't find a screen for miner, when i tried 'screen -r miner' on quake terminal, still no luck.
Any Idea why?
Do you use last nvOC version with all update from OP ?
If yes, put all your OC setting to 0, and try again.
In the 1bash file, make sure u do
Quote
LOCALorREMOTE="LOCAL" # LOCAL or REMOTE
If u have a screen attached, and try again. If u are on ssh with no screen attached do
Quote
screen -ls
### To attach the screen ### Quote
screen -x miner
Thanks for your reply.
Yes, my rig is up to date with nvOC v 18 with all files.
I was dual mining which was working perfectly well, have stopped it and tried to mine SIGT using your instructions but didn't work. I use local and other coins working as normal.
Anyway will try with 0 of settings and see again, thanks alot for those instructions though.
I've managed to make it work with my RIG, it seems working fine (issue was with path as mentioned in one of the replies).
Getting around 125 MH with my 8x 1060 6GB ASUS (oc:0,mc:0,pl:80), please share you OC settings if you think I'm getting low hashrate.
Thanks.
I dont know about 1060, but on skunk algo, u dont care about mc so put them in lower value, max as u can for 1070 is -2000.
Up your powerlimit to the default powerlimit and Clockmemory step by step start at 100, wait 24h and increment by 10 after every 24hours before crash.
When crash occur reduce to the previous step, wait again more 24h if stable lower your powerlimit to get a better ratio watt / hashrate.
So for my ASUS 1070 GTX 8OG
MemClock : -2000
CoreClock : 130 ( the 24hours step, i go push to 130 just now )
PowerLimit : 150W per gpu
TempLimit : 70c
Fan range : 95-75 ( autotemp ON )
As SIGT is running good for 2500 blocks after reward get halved, i suggest you to get a stable setting cause watchdog is disable, so if your RIG crash, he dont gona reboot him self
Hi guys,
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
SECOND STEP EDIT BASH
### Open 1bash
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
Quote
cd /m1/home/
### Create a directory for your new miner ###Quote
mkdir PMccminer
### Go in new dir ###Quote
cd PMccminer/
### Download miner client ### Quote
### Extract the file ###Quote
tar -zxvf palginmod_1.1_Ubuntu.tar.gz
### Delete start.sh ###Quote
rm start.sh
### Back to home dir ###Quote
cd /m1/home/
SECOND STEP EDIT BASH
### Open 1bash
Quote
nano 1bash
### Add SIGT and SIGT_BTC to the coin selection Quote
# CHOOSE COIN FROM:
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
Quote
SIGT_WORKER="SIGT"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
Quote
BTC_ADDRESS="3JJaMUVBJp55BNsGvYynaJhDXRyUf95hyG"
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
Quote
if [ $COIN == "SIGT_BTC" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Quote
IAmNotAJeep_and_Maxximus007_WATCHDOG="NO"
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
I've tried with my 1060 6G rig, it failed saying can't find a screen for miner, when i tried 'screen -r miner' on quake terminal, still no luck.
Any Idea why?
Do you use last nvOC version with all update from OP ?
If yes, put all your OC setting to 0, and try again.
In the 1bash file, make sure u do
Quote
LOCALorREMOTE="LOCAL" # LOCAL or REMOTE
If u have a screen attached, and try again. If u are on ssh with no screen attached do
Quote
screen -ls
### To attach the screen ### Quote
screen -x miner
Thanks for your reply.
Yes, my rig is up to date with nvOC v 18 with all files.
I was dual mining which was working perfectly well, have stopped it and tried to mine SIGT using your instructions but didn't work. I use local and other coins working as normal.
Anyway will try with 0 of settings and see again, thanks alot for those instructions though.
I've managed to make it work with my RIG, it seems working fine (issue was with path as mentioned in one of the replies).
Getting around 125 MH with my 8x 1060 6GB ASUS (oc:0,mc:0,pl:80), please share you OC settings if you think I'm getting low hashrate.
Thanks.
Ok I was able to root and pull the current specs of my cards.
This is an 4x Gigabyte gtx 10606gb rig.
I have my MC set to 1050 in 1bash and if I'm reading this right it says I'm at a current clock of 8748 with a max of 8754.
How do I get more than a 750 MC increase?
This is an 4x Gigabyte gtx 10606gb rig.
I have my MC set to 1050 in 1bash and if I'm reading this right it says I'm at a current clock of 8748 with a max of 8754.
How do I get more than a 750 MC increase?
If u want to mine SIGT u have to lower your MemTransferRate and up your nvclock
http://imgur.com/a/yZuOE
Be in root and
nvidia-settings -a /GPUGraphicsClockOffset[3]=value
nvidia-settings -a /GPUMemoryTransferRateOffset[3]=value
U can specify by GPU, like the other command
nvidia-settings -a [gpu:0]/GPUGraphicsClockOffset[3]=value
nvidia-settings -a [gpu:0]/GPUMemoryTransferRateOffset[3]=value
Ok I was able to root and pull the current specs of my cards.
This is an 4x Gigabyte gtx 10606gb rig.
I have my MC set to 1050 in 1bash and if I'm reading this right it says I'm at a current clock of 8748 with a max of 8754.
How do I get more than a 750 MC increase?
https://i.imgur.com/Fh5XRQ4.png
This is an 4x Gigabyte gtx 10606gb rig.
I have my MC set to 1050 in 1bash and if I'm reading this right it says I'm at a current clock of 8748 with a max of 8754.
How do I get more than a 750 MC increase?
https://i.imgur.com/Fh5XRQ4.png
Ok so I made it to page 30 something before deciding to post!
So I've currently got 2 rigs that have been running smoothly.
With that being said I've decided to play around and tweak the memorie settings.
This is where I am hitting a wall.
When I set the memory OC say 900/950 then when I check on it in the Nvidia Xserver it shows the clocks at level 2 at 8600-8700 and does not vary much from there.
https://i.imgur.com/srfFFdh.png
So I've currently got 2 rigs that have been running smoothly.
With that being said I've decided to play around and tweak the memorie settings.
This is where I am hitting a wall.
When I set the memory OC say 900/950 then when I check on it in the Nvidia Xserver it shows the clocks at level 2 at 8600-8700 and does not vary much from there.
https://i.imgur.com/srfFFdh.png
U have to be root do "su" and prompt "miner1" as password
nvidia-settings -q /GPUCurrentClockFreqsString
Give u real specs
, u can specify by nvidia-settings -q [gpu:0]/GPUCurrentClockFreqsString
Change 0 value by the GPU u want to ask.
Ok so I forgot to mention I am 100% noob!
What do you mean by root?
So I opened a new terminal.
When I type SU into the terminal is doesn't do anything.
https://i.imgur.com/E3yHXVq.png
Root? You should really read this: http://www.linfo.org/root.html But the TLDR; is Linux systems have multiple users. You are logging in with a regular user account which cannot run all commands or access all parts of the OS. Usually this is a good thing because it makes it harder to break things. But sometimes you need to change to a higher level user, and root is the highest, and the su command does this. Once you've done what you need to as root you should logout of the root account with: exit
The terminal (command line) might be case sensitive so try su and see if that works.
First time using Linux
I'm using teamview to my phone as a monitor/keyboard/mouse and didn't even consider caps.
Ok so I made it to page 30 something before deciding to post!
So I've currently got 2 rigs that have been running smoothly.
With that being said I've decided to play around and tweak the memorie settings.
This is where I am hitting a wall.
When I set the memory OC say 900/950 then when I check on it in the Nvidia Xserver it shows the clocks at level 2 at 8600-8700 and does not vary much from there.
So I've currently got 2 rigs that have been running smoothly.
With that being said I've decided to play around and tweak the memorie settings.
This is where I am hitting a wall.
When I set the memory OC say 900/950 then when I check on it in the Nvidia Xserver it shows the clocks at level 2 at 8600-8700 and does not vary much from there.
U have to be root do "su" and prompt "miner1" as password
nvidia-settings -q /GPUCurrentClockFreqsString
Give u real specs
, u can specify by nvidia-settings -q [gpu:0]/GPUCurrentClockFreqsString
Change 0 value by the GPU u want to ask.
Ok so I forgot to mention I am 100% noob!
What do you mean by root?
So I opened a new terminal.
When I type SU into the terminal is doesn't do anything.
Root? You should really read this: http://www.linfo.org/root.html But the TLDR; is Linux systems have multiple users. You are logging in with a regular user account which cannot run all commands or access all parts of the OS. Usually this is a good thing because it makes it harder to break things. But sometimes you need to change to a higher level user, and root is the highest, and the su command does this. Once you've done what you need to as root you should logout of the root account with: exit
The terminal (command line) might be case sensitive so try su and see if that works.
Ok so I made it to page 30 something before deciding to post!
So I've currently got 2 rigs that have been running smoothly.
With that being said I've decided to play around and tweak the memorie settings.
This is where I am hitting a wall.
When I set the memory OC say 900/950 then when I check on it in the Nvidia Xserver it shows the clocks at level 2 at 8600-8700 and does not vary much from there.
https://i.imgur.com/srfFFdh.png
So I've currently got 2 rigs that have been running smoothly.
With that being said I've decided to play around and tweak the memorie settings.
This is where I am hitting a wall.
When I set the memory OC say 900/950 then when I check on it in the Nvidia Xserver it shows the clocks at level 2 at 8600-8700 and does not vary much from there.
https://i.imgur.com/srfFFdh.png
U have to be root do "su" and prompt "miner1" as password
nvidia-settings -q /GPUCurrentClockFreqsString
Give u real specs
, u can specify by nvidia-settings -q [gpu:0]/GPUCurrentClockFreqsString
Change 0 value by the GPU u want to ask.
Ok so I forgot to mention I am 100% noob!
What do you mean by root?
So I opened a new terminal.
When I type SU into the terminal is doesn't do anything.
https://i.imgur.com/E3yHXVq.png
Hi guys,
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
SECOND STEP EDIT BASH
### Open 1bash
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
Quote
cd /m1/home/
### Create a directory for your new miner ###Quote
mkdir PMccminer
### Go in new dir ###Quote
cd PMccminer/
### Download miner client ### Quote
### Extract the file ###Quote
tar -zxvf palginmod_1.1_Ubuntu.tar.gz
### Delete start.sh ###Quote
rm start.sh
### Back to home dir ###Quote
cd /m1/home/
SECOND STEP EDIT BASH
### Open 1bash
Quote
nano 1bash
### Add SIGT and SIGT_BTC to the coin selection Quote
# CHOOSE COIN FROM:
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
Quote
SIGT_WORKER="SIGT"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
Quote
BTC_ADDRESS="3JJaMUVBJp55BNsGvYynaJhDXRyUf95hyG"
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
Quote
if [ $COIN == "SIGT_BTC" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Quote
IAmNotAJeep_and_Maxximus007_WATCHDOG="NO"
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
thanks for the walkthrough. there is a few things that i think are backwards on your instructions. on my nvoc the directories are /home/m1/ and you have /m1/home/ in your instructions.
also, with the settings i am entering into the fields for the suprnova pool info, i dont know if they are right or what is going on...i am getting a error when i run the terminal "stratum authentication failed" then trying again in 30 seconds. your settings show:
SIGT_WORKER="SIGT"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
in suprnova, my worker is "firstname.systemnumber" example "lovecoin.sys1" - so would i make my settings look like SIGT_WORKER="lovecoin.sys1" ? also what am i editing to sigt_address?
i changed this line:
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
to
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u SUPRNOVAWORKERLOGIN.SYSTEM -p PASSWORDHERE
and its working. whatever $ADDR is referencing is not working correctly i think.
When you use suprnova, SIGT_ADDRESS is your login, SIGT_WORKER is the name of your created worker on suprnova.
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
So $ADDR is actually login.workername
I specify on the "how to" to set your worker password as "x" or modify on the SIGT section.
Quote
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
Anyway good u get it work
Ok so I made it to page 30 something before deciding to post!
So I've currently got 2 rigs that have been running smoothly.
With that being said I've decided to play around and tweak the memorie settings.
This is where I am hitting a wall.
When I set the memory OC say 900/950 then when I check on it in the Nvidia Xserver it shows the clocks at level 2 at 8600-8700 and does not vary much from there.
So I've currently got 2 rigs that have been running smoothly.
With that being said I've decided to play around and tweak the memorie settings.
This is where I am hitting a wall.
When I set the memory OC say 900/950 then when I check on it in the Nvidia Xserver it shows the clocks at level 2 at 8600-8700 and does not vary much from there.
U have to be root do "su" and prompt "miner1" as password
nvidia-settings -q /GPUCurrentClockFreqsString
Give u real specs
, u can specify by nvidia-settings -q [gpu:0]/GPUCurrentClockFreqsString
Change 0 value by the GPU u want to ask.
Ok so I made it to page 30 something before deciding to post!
So I've currently got 2 rigs that have been running smoothly.
With that being said I've decided to play around and tweak the memorie settings.
This is where I am hitting a wall.
When I set the memory OC say 900/950 then when I check on it in the Nvidia Xserver it shows the clocks at level 2 at 8600-8700 and does not vary much from there.
https://i.imgur.com/srfFFdh.png
So I've currently got 2 rigs that have been running smoothly.
With that being said I've decided to play around and tweak the memorie settings.
This is where I am hitting a wall.
When I set the memory OC say 900/950 then when I check on it in the Nvidia Xserver it shows the clocks at level 2 at 8600-8700 and does not vary much from there.
https://i.imgur.com/srfFFdh.png
Hi guys,
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
SECOND STEP EDIT BASH
### Open 1bash
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
Quote
cd /home/m1/
### Create a directory for your new miner ###Quote
mkdir PMccminer
### Go in new dir ###Quote
cd PMccminer/
### Download miner client ### Quote
### Extract the file ###Quote
tar -zxvf palginmod_1.1_Ubuntu.tar.gz
### Delete start.sh ###Quote
rm start.sh
### Back to home dir ###Quote
cd /home/m1/
SECOND STEP EDIT BASH
### Open 1bash
Quote
nano 1bash
### Add SIGT and SIGT_BTC to the coin selection Quote
# CHOOSE COIN FROM:
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
Quote
SIGT_WORKER="SIGT"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
Quote
BTC_ADDRESS="3JJaMUVBJp55BNsGvYynaJhDXRyUf95hyG"
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
Quote
if [ $COIN == "SIGT_BTC" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Quote
IAmNotAJeep_and_Maxximus007_WATCHDOG="NO"
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
thanks for the walkthrough. there is a few things that i think are backwards on your instructions. on my nvoc the directories are /home/m1/ and you have /m1/home/ in your instructions.
also, with the settings i am entering into the fields for the suprnova pool info, i dont know if they are right or what is going on...i am getting a error when i run the terminal "stratum authentication failed" then trying again in 30 seconds. your settings show:
SIGT_WORKER="SIGT"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
in suprnova, my worker is "firstname.systemnumber" example "lovecoin.sys1" - so would i make my settings look like SIGT_WORKER="lovecoin.sys1" ? also what am i editing to sigt_address?
Nice point about the path, the true one is /home/m1, i edit the post
SIGT_WORKER="sys1"
SIGT_ADDRESS="lovecoin"
Will do the job
Hi guys,
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
SECOND STEP EDIT BASH
### Open 1bash
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
Quote
cd /m1/home/
### Create a directory for your new miner ###Quote
mkdir PMccminer
### Go in new dir ###Quote
cd PMccminer/
### Download miner client ### Quote
### Extract the file ###Quote
tar -zxvf palginmod_1.1_Ubuntu.tar.gz
### Delete start.sh ###Quote
rm start.sh
### Back to home dir ###Quote
cd /m1/home/
SECOND STEP EDIT BASH
### Open 1bash
Quote
nano 1bash
### Add SIGT and SIGT_BTC to the coin selection Quote
# CHOOSE COIN FROM:
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
Quote
SIGT_WORKER="SIGT"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
Quote
BTC_ADDRESS="3JJaMUVBJp55BNsGvYynaJhDXRyUf95hyG"
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
Quote
if [ $COIN == "SIGT_BTC" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Quote
IAmNotAJeep_and_Maxximus007_WATCHDOG="NO"
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
thanks for the walkthrough. there is a few things that i think are backwards on your instructions. on my nvoc the directories are /home/m1/ and you have /m1/home/ in your instructions.
also, with the settings i am entering into the fields for the suprnova pool info, i dont know if they are right or what is going on...i am getting a error when i run the terminal "stratum authentication failed" then trying again in 30 seconds. your settings show:
SIGT_WORKER="SIGT"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
in suprnova, my worker is "firstname.systemnumber" example "lovecoin.sys1" - so would i make my settings look like SIGT_WORKER="lovecoin.sys1" ? also what am i editing to sigt_address?
i changed this line:
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
to
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u SUPRNOVAWORKERLOGIN.SYSTEM -p PASSWORDHERE
and its working. whatever $ADDR is referencing is not working correctly i think.
Hi guys,
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
SECOND STEP EDIT BASH
### Open 1bash
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
i do a little "how to" if some people want to mine SIGT / skunk algo.
First of all i use Palginmodccminer ( the SP_MOD is faster but u have to pay )
FIRST STEP GET THE CLIENT
### Be in home dir ###
Quote
cd /m1/home/
### Create a directory for your new miner ###Quote
mkdir PMccminer
### Go in new dir ###Quote
cd PMccminer/
### Download miner client ### Quote
### Extract the file ###Quote
tar -zxvf palginmod_1.1_Ubuntu.tar.gz
### Delete start.sh ###Quote
rm start.sh
### Back to home dir ###Quote
cd /m1/home/
SECOND STEP EDIT BASH
### Open 1bash
Quote
nano 1bash
### Add SIGT and SIGT_BTC to the coin selection Quote
# CHOOSE COIN FROM:
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
# DMD GRS ZPOOL_LYRA2V2 ZPOOL_BLAKE2S
# ZEC ZCOIN HUSH ZEN ZCL SIGT SIGT_BTC
# NICE_ETHASH ETH MUSIC ETC EXP DCR PASC
# MONA VTC DGB SIA FTC LBC
# DUAL_ETC_DCR DUAL_ETC_PASC DUAL_ETC_LBC DUAL_ETC_SC
# DUAL_EXP_DCR DUAL_EXP_PASC DUAL_EXP_LBC DUAL_EXP_SC
# DUAL_ETH_DCR DUAL_ETH_PASC DUAL_ETH_LBC DUAL_ETH_SC
# DUAL_MUSIC_DCR DUAL_MUSIC_PASC DUAL_MUSIC_LBC DUAL_MUSIC_SC
### Add SIGT and SIGT_BTC specs ( u have to modify SIGT_WORKER and SIGT_ADDRESS by your seting )
Quote
SIGT_WORKER="SIGT"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
###SIGT_BTC use BTC adresses###
SIGT_BTC_POOL="stratum+tcp://skunk.mine.zpool.ca:8433"
### If u use SIGT_BTC, be sure to get correct ( your BTC adress )
Quote
BTC_ADDRESS="3JJaMUVBJp55BNsGvYynaJhDXRyUf95hyG"
### Add miner specs to the end of ur file between the two last "fi" ( ensure ur worker have x password on suprnova pool, or modify the "-p x" by "-p YourPassword" in the SIGT section )
Quote
if [ $COIN == "SIGT_BTC" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$BTC_ADDRESS"
screen -dmS miner $HCD -a skunk -o $SIGT_BTC_POOL -u $ADDR -p c=SIGT
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
if [ $COIN == "SIGT" ]
then
HCD='/home/m1/PMccminer/ccminer'
ADDR="$SIGT_ADDRESS.$SIGT_WORKER"
screen -dmS miner $HCD -a skunk -o $SIGT_POOL -u $ADDR -p x
if [ $LOCALorREMOTE == "LOCAL" ]
then
screen -r miner
fi
BITCOIN="theGROUND"
while [ $BITCOIN == "theGROUND" ]
do
sleep 60
done
fi
THIRD STEP OC SETTING ( ASUS 1070 GTX 8OG / prolly ok for most 1070 gtx )
First of all this algo, gona get a lot of heat from your card, he use core, not memory.
CoreClock : 120
MemClock : -2000
PowerLimit at default : 150W
Temp Target 70°
Fan between 95% - 75% ( I use watchdog )
This fine tunning work like a charm 213mh/s on suprnova, 211mh/s on zpool
U have to disable
Quote
IAmNotAJeep_and_Maxximus007_WATCHDOG="NO"
Or your RIG gona get restart for nothing, i dont modify IAmNotAJeep_and_Maxximus007_WATCHDOG, if i do prolly i can get him work with this setup but more simple to stop him for this coin
Et voila
thanks for the walkthrough. there is a few things that i think are backwards on your instructions. on my nvoc the directories are /home/m1/ and you have /m1/home/ in your instructions.
also, with the settings i am entering into the fields for the suprnova pool info, i dont know if they are right or what is going on...i am getting a error when i run the terminal "stratum authentication failed" then trying again in 30 seconds. your settings show:
SIGT_WORKER="SIGT"
SIGT_ADDRESS="Bibi187"
SIGT_POOL="stratum+tcp://sigt.suprnova.cc:7106"
in suprnova, my worker is "firstname.systemnumber" example "lovecoin.sys1" - so would i make my settings look like SIGT_WORKER="lovecoin.sys1" ? also what am i editing to sigt_address?
Jump to: