PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux) - page 322.

burntroach85

newbie

Activity: 17

Merit: 0

Quote from: UnclWish on August 24, 2019, 03:36:19 PM

Quote from: burntroach85 on August 24, 2019, 02:45:12 PM

so guys i have a question maybe someone could help me with please, im running 13 cards and for example i want to run some on clkernal 3 and some on clkernal 2 how would i go about doing this? thank you again for you time and any help at all

-clKernel 3,2,2,2,3 etc.

Thank you man very much

Digital_Seytan

jr. member

Activity: 222

Merit: 2

[email protected]

Quote from: gorkemg on August 26, 2019, 03:32:56 PM

I'm getting these errors with 4.5c on 8x p106 rig :

NVAPI error in NvapiWrapper.c:445 : -6
Unable to load NvAPI: error 3
Eth: the pool list contains 1 pool (1 from command-line)
Eth: primary pool: eu1-etc.ethermine.org:4444
Starting GPU mining
GPU1: unable to init NvAPI with bus ID 65536
GPU2: unable to init NvAPI with bus ID 131072
GPU3: unable to init NvAPI with bus ID 262144
GPU4: unable to init NvAPI with bus ID 327680
GPU5: unable to init NvAPI with bus ID 393216
GPU6: unable to init NvAPI with bus ID 458752
GPU7: unable to init NvAPI with bus ID 524288
GPU8: unable to init NvAPI with bus ID 589824

After these errors , Miner seems work like 4.2c

Any idea ?

NVAPI error in NvapiWrapper.c:445 : -6
Unable to load NvAPI: error 3

Thanks for this message, I also have the same type of gtu 106 gpu cards. Also get the same message. Of course the phoenixminer dev should remedy this, I think in the next version.

gorkemg

newbie

Activity: 29

Merit: 0

I'm getting these errors with 4.5c on 8x p106 rig :

NVAPI error in NvapiWrapper.c:445 : -6
Unable to load NvAPI: error 3
Eth: the pool list contains 1 pool (1 from command-line)
Eth: primary pool: eu1-etc.ethermine.org:4444
Starting GPU mining
GPU1: unable to init NvAPI with bus ID 65536
GPU2: unable to init NvAPI with bus ID 131072
GPU3: unable to init NvAPI with bus ID 262144
GPU4: unable to init NvAPI with bus ID 327680
GPU5: unable to init NvAPI with bus ID 393216
GPU6: unable to init NvAPI with bus ID 458752
GPU7: unable to init NvAPI with bus ID 524288
GPU8: unable to init NvAPI with bus ID 589824

After these errors , Miner seems work like 4.2c

Any idea ?

UnclWish

sr. member

Activity: 1484

Merit: 253

Quote from: burntroach85 on August 24, 2019, 02:45:12 PM

so guys i have a question maybe someone could help me with please, im running 13 cards and for example i want to run some on clkernal 3 and some on clkernal 2 how would i go about doing this? thank you again for you time and any help at all

-clKernel 3,2,2,2,3 etc.

burntroach85

newbie

Activity: 17

Merit: 0

so guys i have a question maybe someone could help me with please, im running 13 cards and for example i want to run some on clkernal 3 and some on clkernal 2 how would i go about doing this? thank you again for you time and any help at all

UnclWish

sr. member

Activity: 1484

Merit: 253

Quote from: ?? on ??

@PhoenixMiner
sometimes nicehash algo daggerhashimoto mine unknown coin with 0.00 hashrate.

I didn't think that it's miner issue. I noticed that when speed is 0.00 there is no new jobs from pool.
Maybe it's just not enough jobs on old nicehash pool?

UnclWish

sr. member

Activity: 1484

Merit: 253

Quote from: ?? on ??

Quote from: UnclWish on August 22, 2019, 01:10:31 PM

Quote from: ?? on ??

Quote

EDIT for the records PhoenixMiner 4.5c works better than Claymore 14.7

Hash Phoenix 4.5c lower Claymore 14.7 with rxboot option

You may use AMD Memory Tweak tool with Phoenix to set REF parameter - this is what Claymore rxboot did. And with that tool you can change this parameter on the fly, Clyamore needs to restart every time.

Thank you, i try and get better result. But how to auto set profile for AMD Memory Tweak for all vga when i restart pc.
Thank again

I didn't know. Ask in their theme - https://bitcointalk.org/index.php?topic=5123724.920

UnclWish

sr. member

Activity: 1484

Merit: 253

Quote from: ?? on ??

Quote

EDIT for the records PhoenixMiner 4.5c works better than Claymore 14.7

Hash Phoenix 4.5c lower Claymore 14.7 with rxboot option

You may use AMD Memory Tweak tool with Phoenix to set REF parameter - this is what Claymore rxboot did. And with that tool you can change this parameter on the fly, Clyamore needs to restart every time.

ManDoneKTM

newbie

Activity: 150

Merit: 0

Quote from: karim_hassan777 on August 21, 2019, 01:28:52 PM

Does any one know AMD team will resolve the TLB problem for RX 5700 XT or not ?

before you comment , read a few pages back Wink

you will find the answer .

zertor

jr. member

Activity: 56

Merit: 6

Code:

Unable to load NVML

what could be the reason for this error?

karim_hassan777

newbie

Activity: 58

Merit: 0

Does any one know AMD team will resolve the TLB problem for RX 5700 XT or not ?

UnclWish

sr. member

Activity: 1484

Merit: 253

Quote from: ?? on ??

@PhoenixMiner
sometimes nicehash algo daggerhashimoto mine unknown coin with 0.00 hashrate.

Confirm, sometimes nicehash mines with 0.00 hashrate. Looks like it's some new ethereum fork appears...

camchimonline

newbie

Activity: 32

Merit: 0

I don’t be used-mt option with driver 19.5.1 on rx 570 4gb. I get all crash.
Anyone help me.
Thank

mochaaa

jr. member

Activity: 76

Merit: 3

@phoenixminer is there a way to access the strap database ?

elmanager

sr. member

Activity: 306

Merit: 250

Cryptobulgarian ninja

Quote from: PhoenixMiner on August 21, 2019, 12:32:23 AM

Quote from: elmanager on August 20, 2019, 02:03:35 PM

Did anyone try ETC in ethermine, it looks like it doesn't read "-"(dash) and . (dot) in the pool link in the config. In the console shows connected as its pointed in the config but actually it doesnt read the subdomain. I'm using 4.5c with smos. eu1-etc.ethermine.org:4444. I was waiting about 2 hours the rigs to appear, meantime everything was looking fine, then i decided to check the etc address in the eth pool and yes, it was there.

It works fine with eu1-etc.ethermine.org:4444 or any other ethermine ETC pool (both when specified in the command-line or config.txt with -pool and when specified in the epools.tt). Please check your configuration and your log file - most probably the first pool is left to ETH ethermine from before you change to ETC. In the log file you will see how many pools are read from the command-line or config.txt and how many from epools.txt. You can also see the list of all pools by pressing the 'e' key when in miner console.

Thank You thats all I need to know, I'm using SMOS as I mentioned above, so maybe I need to edit smos on each rig. Thats my config line in smos: -pool eu1-etc.ethermine.org:4444 -wal 0xwalletaddress.001 -rmode 2 In the console miner says it is connected to eu1-etc.ethermine.org but the shares actually came from the its eth pool.
EDIT for the records PhoenixMiner 4.5c works better than Claymore 14.7

PhoenixMiner

full member

Activity: 357

Merit: 101

Quote from: elmanager on August 20, 2019, 02:03:35 PM

Did anyone try ETC in ethermine, it looks like it doesn't read "-"(dash) and . (dot) in the pool link in the config. In the console shows connected as its pointed in the config but actually it doesnt read the subdomain. I'm using 4.5c with smos. eu1-etc.ethermine.org:4444. I was waiting about 2 hours the rigs to appear, meantime everything was looking fine, then i decided to check the etc address in the eth pool and yes, it was there.

It works fine with eu1-etc.ethermine.org:4444 or any other ethermine ETC pool (both when specified in the command-line or config.txt with -pool and when specified in the epools.tt). Please check your configuration and your log file - most probably the first pool is left to ETH ethermine from before you change to ETC. In the log file you will see how many pools are read from the command-line or config.txt and how many from epools.txt. You can also see the list of all pools by pressing the 'e' key when in miner console.

fomkas

newbie

Activity: 30

Merit: 0

Quote from: elmanager on August 20, 2019, 02:03:35 PM

Did anyone try ETC in ethermine, it looks like it doesn't read "-"(dash) and . (dot) in the pool link in the config. In the console shows connected as its pointed in the config but actually it doesnt read the subdomain. I'm using 4.5c with smos. eu1-etc.ethermine.org:4444. I was waiting about 2 hours the rigs to appear, meantime everything was looking fine, then i decided to check the etc address in the eth pool and yes, it was there.

i jast see

ethermine.org (ETC):
PhoenixMiner.exe -pool eu1-etc.ethermine.org:4444 -wal YourEtcWalletAddress.WorkerName

in first post

elmanager

sr. member

Activity: 306

Merit: 250

Cryptobulgarian ninja

Did anyone try ETC in ethermine, it looks like it doesn't read "-"(dash) and . (dot) in the pool link in the config. In the console shows connected as its pointed in the config but actually it doesnt read the subdomain. I'm using 4.5c with smos. eu1-etc.ethermine.org:4444. I was waiting about 2 hours the rigs to appear, meantime everything was looking fine, then i decided to check the etc address in the eth pool and yes, it was there.

Branko

sr. member

Activity: 2632

Merit: 328

Quote from: Iamtutut on August 16, 2019, 02:09:18 PM

I am amazed PhoenixMiner has only 10 merits considering the number of people using this miner.

Well, glory times of GPU mining are for the most part over, thats probably the reason.
Gave it 1 merit, anyway Grin

Iamtutut

full member

Activity: 1120

Merit: 131

I am amazed PhoenixMiner has only 10 merits considering the number of people using this miner.

Topic: PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux) - page 322. (Read 784965 times)