[POOL] --- Coinotron --- RavenCoin PPS: 1.5% ----- PPLNS, RBPPS: 0% --------- - page 84.

xorxor

sr. member

Activity: 476

Merit: 253

Quote from: itsgoldbaby on March 15, 2013, 12:40:07 PM

cgminer -o stratum+tcp://coinotron.com:3334 -u myusername -p mypassword --scrypt --thread-concurrency 6144 -I 12 -g 1 -w 256. The temp for the card was low 70's. It was showing roughly 250h/s in cgminer but showing up in the 50kh/s on coinotron. Didn't take down the Accepts/Rejects/Total HW, but it was over 150.

I have switched back to bitcoin for now, I had 2 cgminers opened. One for my bfl and one for litecoin on my other computer. Getting a bit tired now and might fuck something up to much, gonna take a break. But if you do have any advice it would be greatly appreciated. Thanks.

-I 18

and that will KILL your desktop. scrypt is dedicated only. if you mine od desktop you should go back to sha256 and try PPC or TRC - here on the same pool

itsgoldbaby

full member

Activity: 157

Merit: 100

Hello!

Quote from: xorxor on March 15, 2013, 12:30:16 PM

Quote from: itsgoldbaby on March 15, 2013, 12:10:33 PM

Quote from: xorxor on March 15, 2013, 11:59:48 AM

Quote from: itsgoldbaby on March 15, 2013, 11:11:38 AM

How long does it take for the accurate hash rates to shows for my miners? I have set up a 6770 (108.4 KH/s, cgminer = 135.1KH/s ), and a 6870 (59.4 KH/s, cgminer = 147.1 KH/s). The 6770 is showing close to what cgminer is showing, but the 6870 is way off. It's been about 30 minutes. The 6870 is the second miner, would that matter? New to litecoin.

also check your first line in CGminer - Q: A: R: HW: E: U:

Q , E , U - useless

(A/(A+R))*100% = your efficiency, should not drop below 90%. for me [my conection] its 95% for coinotron and much worse for notroll , ozcoin and burnside

HW: most important , MUST BE 0 !!! or your card or setup is bad

you should get minimum 150kh from 6770 and 250kh from 6870 , add --thread-concurrency 6144 parameter

Interesting, my HW:was 150 on my 6870... ?? What would be causing it to be so high?

give us your cminer starting line ,

report all A: R: HW: , cause hw 150 on a 45000 is "a little" different than hw:150 on A:30
report your temp's

This is what I was using to start cgminer for litecoin:

cgminer -o stratum+tcp://coinotron.com:3334 -u myusername -p mypassword --scrypt --thread-concurrency 6144 -I 12 -g 1 -w 256. The temp for the card was low 70's. It was showing roughly 250h/s in cgminer but showing up in the 50kh/s on coinotron. Didn't take down the Accepts/Rejects/Total HW, but it was over 150.

I have switched back to bitcoin for now, I had 2 cgminers opened. One for my bfl and one for litecoin on my other computer. Getting a bit tired now and might fuck something up to much, gonna take a break. But if you do have any advice it would be greatly appreciated. Thanks.

xorxor

sr. member

Activity: 476

Merit: 253

Quote from: itsgoldbaby on March 15, 2013, 12:10:33 PM

Quote from: xorxor on March 15, 2013, 11:59:48 AM

Quote from: itsgoldbaby on March 15, 2013, 11:11:38 AM

How long does it take for the accurate hash rates to shows for my miners? I have set up a 6770 (108.4 KH/s, cgminer = 135.1KH/s ), and a 6870 (59.4 KH/s, cgminer = 147.1 KH/s). The 6770 is showing close to what cgminer is showing, but the 6870 is way off. It's been about 30 minutes. The 6870 is the second miner, would that matter? New to litecoin.

also check your first line in CGminer - Q: A: R: HW: E: U:

Q , E , U - useless

(A/(A+R))*100% = your efficiency, should not drop below 90%. for me [my conection] its 95% for coinotron and much worse for notroll , ozcoin and burnside

HW: most important , MUST BE 0 !!! or your card or setup is bad

you should get minimum 150kh from 6770 and 250kh from 6870 , add --thread-concurrency 6144 parameter

Interesting, my HW:was 150 on my 6870... ?? What would be causing it to be so high?

give us your cminer starting line ,

report all A: R: HW: , cause hw 150 on a 45000 is "a little" different than hw:150 on A:30
report your temp's

itsgoldbaby

full member

Activity: 157

Merit: 100

Hello!

Quote from: xorxor on March 15, 2013, 11:59:48 AM

Quote from: itsgoldbaby on March 15, 2013, 11:11:38 AM

How long does it take for the accurate hash rates to shows for my miners? I have set up a 6770 (108.4 KH/s, cgminer = 135.1KH/s ), and a 6870 (59.4 KH/s, cgminer = 147.1 KH/s). The 6770 is showing close to what cgminer is showing, but the 6870 is way off. It's been about 30 minutes. The 6870 is the second miner, would that matter? New to litecoin.

also check your first line in CGminer - Q: A: R: HW: E: U:

Q , E , U - useless

(A/(A+R))*100% = your efficiency, should not drop below 90%. for me [my conection] its 95% for coinotron and much worse for notroll , ozcoin and burnside

HW: most important , MUST BE 0 !!! or your card or setup is bad

you should get minimum 150kh from 6770 and 250kh from 6870 , add --thread-concurrency 6144 parameter

Interesting, my HW:was 150 on my 6870... ?? What would be causing it to be so high?

xorxor

sr. member

Activity: 476

Merit: 253

Quote from: itsgoldbaby on March 15, 2013, 11:11:38 AM

How long does it take for the accurate hash rates to shows for my miners? I have set up a 6770 (108.4 KH/s, cgminer = 135.1KH/s ), and a 6870 (59.4 KH/s, cgminer = 147.1 KH/s). The 6770 is showing close to what cgminer is showing, but the 6870 is way off. It's been about 30 minutes. The 6870 is the second miner, would that matter? New to litecoin.

also check your first line in CGminer - Q: A: R: HW: E: U:

Q , E , U - useless

(A/(A+R))*100% = your efficiency, should not drop below 90%. for me [my conection] its 95% for coinotron and much worse for notroll , ozcoin and burnside

HW: most important , MUST BE 0 !!! or your card or setup is bad

you should get minimum 150kh from 6770 and 250kh from 6870 , add --thread-concurrency 6144 parameter

coinotron

legendary

Activity: 1182

Merit: 1000

Quote from: itsgoldbaby on March 15, 2013, 11:11:38 AM

How long does it take for the accurate hash rates to shows for my miners? I have set up a 6770 (108.4 KH/s, cgminer = 135.1KH/s ), and a 6870 (59.4 KH/s, cgminer = 147.1 KH/s). The 6770 is showing close to what cgminer is showing, but the 6870 is way off. It's been about 30 minutes. The 6870 is the second miner, would that matter? New to litecoin.

Simple answer = 10 min.
If your miner hashrate is not very high (6870) and you are mining at stratum pool where share difficulty is 32, then variance of hashrates reported by website may be way off

Your miner simply doesn't submit enough shares in 10 min period to allow pool calc accurate estimations of miners' hashrate.

itsgoldbaby

full member

Activity: 157

Merit: 100

Hello!

How long does it take for the accurate hash rates to shows for my miners? I have set up a 6770 (108.4 KH/s, cgminer = 135.1KH/s ), and a 6870 (59.4 KH/s, cgminer = 147.1 KH/s). The 6770 is showing close to what cgminer is showing, but the 6870 is way off. It's been about 30 minutes. The 6870 is the second miner, would that matter? New to litecoin.

DarkHyudrA

legendary

Activity: 1386

Merit: 1000

English <-> Portuguese translations

Quote from: coinotron on March 15, 2013, 09:06:21 AM

hmm strange,
TRC hashrate > LTC hashrate

ASICs maybe?

coinotron

legendary

Activity: 1182

Merit: 1000

hmm strange,
TRC hashrate > LTC hashrate

coinotron

legendary

Activity: 1182

Merit: 1000

Quote from: flound1129 on March 15, 2013, 02:30:48 AM

Seems like .00044154 is double .00022077. Your calculator working?

You are correct.
.00044154 ( at share diff 32) is double .00022077 (at share diff 16 )

In other words: reward 0.00044154 is doubled but additionally your work is twice as much difficult

flound1129

hero member

Activity: 938

Merit: 1000

www.multipool.us

Quote from: xorxor on March 14, 2013, 04:20:03 PM

Quote from: flound1129 on March 14, 2013, 02:58:38 PM

So if you're using stratum the rate is effectively double?

no of course not.

simply notroll is 0.00043249 only
and coinotron is 0.00044154 AND 0.00022077 for getwork

Seems like .00044154 is double .00022077. Your calculator working?

celkaris

full member

Activity: 148

Merit: 100

Quote from: coinotron on March 13, 2013, 06:14:45 PM

Quote from: sal002 on March 13, 2013, 07:27:11 AM

Good point - but Terracoin and PPCoin are the new ixcoin / Devcoin (http://www.coinchoose.com). However, I think it would be nice to provide programmatic functionality outside of the pool web-site just in case any site has calculations on the most profitable coin to mine that also may be accessed via an API

API to change worker coin. It is a shame, I didn't think of it.
OK, added to todo/wishlist

although interesting/useful i guess, this may also let many chains in some 'stuck' state, finally moving all miners to btc-only once all chains were "cycled until under 100% profitability" ?

xorxor

sr. member

Activity: 476

Merit: 253

Quote from: flound1129 on March 14, 2013, 02:58:38 PM

Quote from: coinotron on March 14, 2013, 02:55:45 PM

Quote from: flound1129 on March 14, 2013, 02:00:23 PM

Coinotron lists a 3.5% PPS fee, and the PPS rate is 0.00022077
Notroll.in lists a 4% fee and the PPS rate is 0.00043249324521070000

So.. What accounts for this difference? cgminer is showing them both at 32 difficulty.

This rate is calculated for getwork pool where share difficulty = 16.
Stratum diff is 32.

So if you're using stratum the rate is effectively double?

no of course not.

simply notroll is 0.00043249 only
and coinotron is 0.00044154 AND 0.00022077 for getwork

flound1129

hero member

Activity: 938

Merit: 1000

www.multipool.us

Quote from: coinotron on March 14, 2013, 02:55:45 PM

Quote from: flound1129 on March 14, 2013, 02:00:23 PM

Coinotron lists a 3.5% PPS fee, and the PPS rate is 0.00022077
Notroll.in lists a 4% fee and the PPS rate is 0.00043249324521070000

So.. What accounts for this difference? cgminer is showing them both at 32 difficulty.

This rate is calculated for getwork pool where share difficulty = 16.
Stratum diff is 32.

So if you're using stratum the rate is effectively double?

coinotron

legendary

Activity: 1182

Merit: 1000

Quote from: flound1129 on March 14, 2013, 02:00:23 PM

Coinotron lists a 3.5% PPS fee, and the PPS rate is 0.00022077
Notroll.in lists a 4% fee and the PPS rate is 0.00043249324521070000

So.. What accounts for this difference? cgminer is showing them both at 32 difficulty.

This rate is calculated for getwork pool where share difficulty = 16.
Stratum diff is 32.

coinotron

legendary

Activity: 1182

Merit: 1000

Quote from: flound1129 on March 14, 2013, 02:43:48 PM

Quote from: ewibit on March 14, 2013, 02:39:43 PM

Quote from: coinotron on March 14, 2013, 01:16:48 PM

cgminer -o stratum+tcp://coinotron.com:3334 -u workername -p password --scrypt

why do I have only 50.0Kh/s with a 5870 with this command?
(with BTC = 400Mh/s)
I think it should be more...

need to tune for your card. look here https://bitcointalksearch.org/topic/consolidated-litecoin-mining-guide-for-5xxx-6xxx-and-7xxx-gpus-117221

And wait 10 minutes. Hashrate calc is based on 10 min period.

flound1129

hero member

Activity: 938

Merit: 1000

www.multipool.us

Quote from: ewibit on March 14, 2013, 02:39:43 PM

Quote from: coinotron on March 14, 2013, 01:16:48 PM

cgminer -o stratum+tcp://coinotron.com:3334 -u workername -p password --scrypt

why do I have only 50.0Kh/s with a 5870 with this command?
(with BTC = 400Mh/s)
I think it should be more...

need to tune for your card. look here https://bitcointalksearch.org/topic/consolidated-litecoin-mining-guide-for-5xxx-6xxx-and-7xxx-gpus-117221

ewibit

legendary

Activity: 2955

Merit: 1049

Quote from: coinotron on March 14, 2013, 01:16:48 PM

cgminer -o stratum+tcp://coinotron.com:3334 -u workername -p password --scrypt

why do I have only 50.0Kh/s with a 5870 with this command?
(with BTC = 400Mh/s)
I think it should be more...

flound1129

hero member

Activity: 938

Merit: 1000

www.multipool.us

Coinotron lists a 3.5% PPS fee, and the PPS rate is 0.00022077
Notroll.in lists a 4% fee and the PPS rate is 0.00043249324521070000

So.. What accounts for this difference? cgminer is showing them both at 32 difficulty.

DarkHyudrA

legendary

Activity: 1386

Merit: 1000

English <-> Portuguese translations

Quote from: montana on March 14, 2013, 01:40:02 PM

Quote from: coinotron on March 14, 2013, 01:16:48 PM

Quote from: HappyScamp on March 14, 2013, 12:02:28 PM

Without reading the whole thread, what is the best, pain-free miner to use, coinotron, and where do I get it?

Thanks

Cgminer, http://ck.kolivas.org/apps/cgminer/

Simplest command to start:
cgminer -o stratum+tcp://coinotron.com:3334 -u workername -p password --scrypt

OK,

Thanks. Now, I click on the folder that calls itself the latest version, and what I get is a blank white page.

You don't need to enter in the versions folders, the WIndows Binaries and .tar are there.

Topic: [POOL] --- Coinotron --- RavenCoin PPS: 1.5% ----- PPLNS, RBPPS: 0% --------- - page 84. (Read 295324 times)