Topic: ROCKMINER ASIC miner official thread - page 42. (Read 199728 times)

FriedCat would have had this s%#t Nailed Down!

Unfortunately when mining solo, cgminer now requires the --btc-address flag, which restricts it to Bitcoin (or so I was told). I mine most alt-coins solo.

And as predicted more failed shortly after posting my last. This time however they ALL failed.
http://imgur.com/J33ofir

Can get someone from rockminer to PM me so I can set up an RMA, refund, something?

Just got my R3 miners and they are hashing beautifully. Simply plug and play and within minutes we are getting 500+ GH!!!

THANK YOU ROCKMINER!!!!

Here are some pictures:





Screenshot of cgminer in webUI:



infact i think these will top 500+ GH no problem. I will post an update after leaving it hashing overnight...so we can see the true speed of this beast  

I have purchased from multiple sources so I am unsure who I purchased the specific unit from 

Ok, so I'm still having my miners crash out. I did have 2 PSUs die, so I replaced them and I was hoping that that was the issue but it does not look like it will be that easy. I re-flashed my sd card, I'm using a known good USB hub, but I'm still having issues. The 6 R-Box miners are the only mining devices running.

Here are some screen shots. In the first one you can see that they were working fine until I got my new PSUs in and hooked up the 2 that I suspect are bad.
http://imgur.com/uY4i5HZ

Then see that not one failed and does not report in the system check. (shortly more will go off line)
http://imgur.com/BhF3dQV

On the devices page it shows so many devices that I don't have. The number keeps growing.
http://imgur.com/dh7j3Lp

Edit: It didn't like the image links

My fan speed controller wasn't PWM so I didn't implement it, but I did replace the fan with a 12V 0.6A fan I had lying around (powered from the PS) and it is much quieter. It doesn't move as much air but the noise levels are tolerable. I did order the PWM controller linked above by Klintay and will use it when it arrives, but for now this is needed for my sanity. The blades are running at 58C or lower when clocked to 320Mhz. Also at 320Mhz after running over 8 hours:

cgminer version 4.3.3 - Started: [2014-07-09 23:36:55]
------------------------------------------------------------------------------
(5s):405.0G (1m):412.3G (5m):412.6G (15m):410.4G (avg):431.0Gh/s
A:2978584  R:190064  HW:210901  WU:6451.6/m  Freq:320MHz
Connected to stratum.bitcoin.cz diff 360 with stratum as user
Block: 29e09c1e...  Diff:16.8G  Started: [07:44:29]  Best share: 1.82M
------------------------------------------------------------------------------
[]SB management []ool management []ettings []isplay options []uit
0: RMU 0       :                   | 106.3G / 107.4Gh/s WU:1650.2/m| T: 58C
1: RMU 1       :                   | 103.8G / 108.2Gh/s WU:1601.5/m| T: 57C
2: RMU 2       :                   | 109.2G / 109.9Gh/s WU:1608.9/m| T: 56C
3: RMU 3       :                   | 98.48G / 105.5Gh/s WU:1591.1/m| T: 58C
------------------------------------------------------------------------------

Also at this configuration with a Bronze rated PS I am drawing 505W at the wall.

Update: It ran great all night but the temps kept climbing. I have re-installed the original fan.

36x ASICMiner Gen3 ?

Is your count correct?

Yeah that is the one mate. It seems to work better than the proper cgminer for me at least.



Also this 10-15% issue. Is it a case of the cgminer not being properly configured to work with these chips? Can it be fixed with software patch...

If you bought from Minersource.net, they normally warranty whatever they sell.

WHEN IS THE 10-15% REJECT RATE ON THE RK-BOXES GOING TO BE ADDRESSED???

Are the R-Box units covered by any warranty? The USB header DE-SOLDERED  from the board 

Dogie's comprehensive RockMiner R3-Box Setup Guide now up!

 

Thanks, where did you get that version of CGMiner? I can't remember where I got it, but the one I download from the main site seems to be different.

UPDATE: Think I found it: https://github.com/rockminerinc/cgminer-for-R-BOX/blob/master/cgminer-win0.3.1.zip

cgminer.exe --icarus-options 115200:1:1 -o stratum.d7.lt:3333 -u iloveppcoin.2 -p 12345 --rmu-freq=320


Using the modified fork of cgminer as well that was provided by Rockminer. It is actually hashing at 460 average now. I think it just depends from unit to unit.

klintay, what is your cgminer command line?

Yeah i agree. I also found excessive thermal paste on some units that was interfering with the chips. Is it necessary to use that much?  

But not all RK-Box units are running at 430 GH. Here is one nice unit i am running:



This one is averaging at 450+ now

R3 is suppose to be a lot more stable, will post pictures tonight.

P2Pool compatibility?  Possible?  Yes? If so, any idea why BFGMiner/CGMiner all get banned shortly after their start with the RK-BOK?  No?  If not, any word on compatibility in the works?  Anybody?

Very cool.  That is good to know.
I have plenty of those fans lying around.

agreed. its unfair to advertise unit such as the rk-box to be running 450-480GH when the actual accepted hashrate is only 390-425GH considering the 9-13% reject rates ive seen