Trouble Shooting!
Please go to the 1st page of this thread!
For a quick notes.
If your miner is missing a white sticker with an IP address printed, you can change your computer's ip setting to.
IP: 192.168.2.254
Subnet:255.255.255.0
Gateway: 192.168.2.1
DNS: 8.8.8.8
Then physically connect ANTMINER to your laptop via Ethernet cable, open the web browser, start trying the address, 192.168.2.1 all the way to 192.168.2.253. More than likely your ip is somewhere between .101 and 253 but if you want to be so anal about it, please try one by one from .1
Other option, set your router setting to
Gateway: 192.168.2.1
DHCP
Subnet: 255.255.255.0
Connect your computer to the router under auto IP config, the. Run anIP scanner software while your AntMiner is connected to your router by the Ethernet. The IP scanner will find your antminer precongigured IP address without have to reset the miner or send it back for the replacement or repair!
If your miners showing average of higher than 169gh and there is no xxxxx on the ASIC chip status but BTCGUILD status shows you 160's or so of hashing number, that could be simply just what was transmitted from your miner over to the network and there is always a slighter number difference. You may also see it higher number than what the antminer's status page shows.
If you see some "x" on the status page, double check your PSU setup and wiring!
Then turn the unit back on and check the status. You may have to reboot a few times to have all 'o' but soon or later it should turn all'o'. Once in a while, it may shows ' 'but as long as it's random and not so frequent, you don't have to worry about too much!
Topic: [Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner - page 158. (Read 452359 times)
In the Bitmain FAQ there's a Q about changing the frequency of AntMiner.
How safe is this as a procedure? I'm only familiar with overclocking CPUs etc. Can the chips run safely at the given top frequency (500MHz)? Is there any other drawback than grown power consumption?
How safe is this as a procedure? I'm only familiar with overclocking CPUs etc. Can the chips run safely at the given top frequency (500MHz)? Is there any other drawback than grown power consumption?
The voltage regulator is a 30AMP device TPS53355.
If each 8chip group draws the rated 30A @ 1.1V your power draw would be ~264W and ~310W using a 80+ Gold PSU.
Well at 400MHz (204GH/s) my 80plus gold 750W PSU draws 512W from the wall (including fan power). That means I am already drawing >30A from the poor regulators and they are overloaded.
As a miner I am looking at RoI first and reliability second.
*photo*
In the new FAQ they mention frequencies from 150 till 500MHz !
But you mentioned running on 400Mhz is already beyond specs, why would they mention anything faster in their FAQ?
Wouldn't anything above 375MHz smoke these voltage regulators or is there something we don't know yet ?
And did you noticed alot of difference in your HW/errors after you applied these mini heatsinks?
Your board shows V1.2, mine is V1.3 and stamped 2013/11/18, this is my info on the chip that you placed the heatsink: 0.47uH 051080
Is that the same as on the V1.2 board?
So I made sure the LAN was set to dhcp and I changed the wan to match my local. I hit save and apply and it's been sitting quite some time at applying changes etc/config/cgminer. How do I know when it is safe to unplug it.
I gave up waiting, plugged it in and it's hashing away happily
I gave up waiting, plugged it in and it's hashing away happily
try the steps and let us know..
https://github.com/AntMiner/AntGen1/blob/master/manual/AntMiner%20FAQ.pdf?raw=true
have you tried scanning your own miner? i had no issues reiping my miners...
change u subnet to 192.168.2.x
then download http://www.advanced-ip-scanner.com/
and scan form 192.168.2.1 to 192.168.2.254
Just received my miner, but there is no sticker with the miners ip-address, how do i find it?
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
change u subnet to 192.168.2.x
then download http://www.advanced-ip-scanner.com/
and scan form 192.168.2.1 to 192.168.2.254
Yes i scanned and found that the same ip address that i had change, but still cant ping or connect or do anything, the miner just flashing the green led and the LAN led also flash green only (with no noise btw).
If there any way to fully reset the control board to the factory setting? pls tell me T_T
trying thank you !!
@bclcjunkie
is work i'm back to 192.168.2.99
and this FAQ just update an hour ago, thank you BITMAIN !! (i try the old ver of FAQ but it not work) this new one good
thank you !!!!
try the steps and let us know..
https://github.com/AntMiner/AntGen1/blob/master/manual/AntMiner%20FAQ.pdf?raw=true
have you tried scanning your own miner? i had no issues reiping my miners...
change u subnet to 192.168.2.x
then download http://www.advanced-ip-scanner.com/
and scan form 192.168.2.1 to 192.168.2.254
Just received my miner, but there is no sticker with the miners ip-address, how do i find it?
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
change u subnet to 192.168.2.x
then download http://www.advanced-ip-scanner.com/
and scan form 192.168.2.1 to 192.168.2.254
Yes i scanned and found that the same ip address that i had change, but still cant ping or connect or do anything, the miner just flashing the green led and the LAN led also flash green only (with no noise btw).
If there any way to fully reset the control board to the factory setting? pls tell me T_T
have you tried scanning your own miner? i had no issues reiping my miners...
change u subnet to 192.168.2.x
then download http://www.advanced-ip-scanner.com/
and scan form 192.168.2.1 to 192.168.2.254
Just received my miner, but there is no sticker with the miners ip-address, how do i find it?
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
change u subnet to 192.168.2.x
then download http://www.advanced-ip-scanner.com/
and scan form 192.168.2.1 to 192.168.2.254
Yes i scanned and found that the same ip address that i had change, but still cant ping or connect or do anything, the miner just flashing the green led and the LAN led also flash green only (with no noise btw).
If there any way to fully reset the control board to the factory setting? pls tell me T_T
have you tried scanning your own miner? i had no issues reiping my miners...
change u subnet to 192.168.2.x
then download http://www.advanced-ip-scanner.com/
and scan form 192.168.2.1 to 192.168.2.254
Just received my miner, but there is no sticker with the miners ip-address, how do i find it?
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
change u subnet to 192.168.2.x
then download http://www.advanced-ip-scanner.com/
and scan form 192.168.2.1 to 192.168.2.254
Well i did changed the ip-adress to the 192.168.1.x to get the miner online, i've heard the fan become louder so it started mining immediately only to discover i was with some Bitmain account
@yuancraft you're my hero Great app!
The miner had 192.168.2.37.
Great app!The miner had 192.168.2.37.
u lucky guy and dont change ip address to subnet 192.168.1.x
or you will go to my situation
BITMAIN HELP
@yuancraft you're my hero Great app!
The miner had 192.168.2.37.
Great app!The miner had 192.168.2.37.
Just received my miner, but there is no sticker with the miners ip-address, how do i find it?
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
change u subnet to 192.168.2.x
then download http://www.advanced-ip-scanner.com/
and scan form 192.168.2.1 to 192.168.2.254
have you also changed your pc's ip to 192.168.1.x subnet?
HELP !!
i follow to this step
Change IP address of the AntMiner [Option]
http://s12.postimg.org/xocz9fyvf/033_networksetting_009_WAN2.jpg
chang ip to 192.168.1.x > save&apply > lost connection with miner .
cant ping 192.168.2.x cant ping 192.168.1.x
im trying to reset but my miner is new version
here the pic
http://i.imgur.com/Ua75bkY.jpg
i follow to this step
Change IP address of the AntMiner [Option]
http://s12.postimg.org/xocz9fyvf/033_networksetting_009_WAN2.jpg
chang ip to 192.168.1.x > save&apply > lost connection with miner .
cant ping 192.168.2.x cant ping 192.168.1.x
im trying to reset but my miner is new version
here the pic
http://i.imgur.com/Ua75bkY.jpg
yes of course
you need a same subnet to connect
Just received my miner, but there is no sticker with the miners ip-address, how do i find it?
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response.
The red light is on and the lan led is blinking so it seems it started.. but what now ?
Can't see any DHCP request on my router either, so it seems it's configured with static ip.
have you also changed your pc's ip to 192.168.1.x subnet?
HELP !!
i follow to this step
Change IP address of the AntMiner [Option]
http://s12.postimg.org/xocz9fyvf/033_networksetting_009_WAN2.jpg
chang ip to 192.168.1.x > save&apply > lost connection with miner .
cant ping 192.168.2.x cant ping 192.168.1.x
im trying to reset but my miner is new version
here the pic
http://i.imgur.com/Ua75bkY.jpg
i follow to this step
Change IP address of the AntMiner [Option]
http://s12.postimg.org/xocz9fyvf/033_networksetting_009_WAN2.jpg
chang ip to 192.168.1.x > save&apply > lost connection with miner .
cant ping 192.168.2.x cant ping 192.168.1.x
im trying to reset but my miner is new version
here the pic
http://i.imgur.com/Ua75bkY.jpg
i follow to this step
Change IP address of the AntMiner [Option]
http://s12.postimg.org/xocz9fyvf/033_networksetting_009_WAN2.jpg
chang ip to 192.168.1.x > save&apply > lost connection with miner .
cant ping 192.168.2.x cant ping 192.168.1.x
im trying to reset but my miner is new version
here the pic
http://i.imgur.com/Ua75bkY.jpg
http://www.mycom.nl/componenten/voedingen/11363/corsair-cxm-430w
http://www.mycom.nl/componenten/voedingen/9613/corsair-cx-500w
can anyone tell me which of the above PSU work best with antminer?
thanks
http://www.mycom.nl/componenten/voedingen/9613/corsair-cx-500w
can anyone tell me which of the above PSU work best with antminer?
thanks
How much power can the fan connector deliver?
the original fan is rated 1.3A (quite high)
thx, Sometimes the answers are so simple...
Bitmain is running the 3rd Auction (less than 8 hours left)
https://bitcointalksearch.org/topic/the-3rd-round-auction-for-the-antminer-s1-dual-blades-120-units-24-hours-355755
How much power can the fan connector deliver?
the original fan is rated 1.3A (quite high) and is capable of >90CFM. it draws voltage directly and there are capacitors on its 12V line for stability.
it is PWM-controlled, though im not sure if its speed is kept relative to the first fan or adjusted individually.
Jump to: