Thanks everyone with the networking support but not there yet.
I now have the Antminer connected to the router via ethernet, it seems to be online and able to ping.
However I'm still not mining I think the problem is this:
Thu Mar 13 01:45:09 2014 kern.warn kernel: [ 21.660000] PIC microchip bootloader usb OK
Thu Mar 13 01:45:09 2014 daemon.notice netifd: lan (647): Sending discover...
Thu Mar 13 01:45:09 2014 kern.info kernel: [ 22.250000] br-wan: port 1(eth1) entered learning state
Thu Mar 13 01:45:09 2014 daemon.info sysinit: command failed: Device or resource busy (-16)
Thu Mar 13 01:45:09 2014 daemon.info sysinit: command failed: Device or resource busy (-16)
Thu Mar 13 01:45:10 2014 daemon.info sysinit: wpa_supplicant_setup_vif(wlan0): Refusing to bridge sta mode interface
Thu Mar 13 01:45:10 2014 daemon.info sysinit: enable_mac80211(radio0): Failed to set up wpa_supplicant for interface wlan0
Thu Mar 13 01:45:11 2014 kern.info kernel: [ 24.250000] br-wan: topology change detected, propagating
Thu Mar 13 01:45:11 2014 kern.info kernel: [ 24.250000] br-wan: port 1(eth1) entered forwarding state
Thu Mar 13 01:45:11 2014 daemon.info sysinit: wpa_supplicant_setup_vif(wlan0-1): Refusing to bridge sta mode interface
Thu Mar 13 01:45:11 2014 daemon.info sysinit: enable_mac80211(radio0): Failed to set up wpa_supplicant for interface wlan0-1
Thu Mar 13 01:45:12 2014 daemon.notice netifd: lan (647): Sending discover...
Thu Mar 13 01:45:18 2014 kern.warn kernel: [ 31.240000] no int in filled
It also hangs at cgminer at the end:
Thu Mar 13 01:48:02 2014 cron.info crond[580]: crond: USER root pid 990 cmd /usr/bin/cgminer-monitor
Its been over a week and still no hashing please help!
Thanks,
--Nick
Bummer, sorry to hear, I'm sure that is very frustrating. I can't remember the trail to know where your problem started, so I'm just going to ask some questions:
- Did the miner ever work i.e. has this error always been in the log?
- Have you changed any of the network settings on the ant?
- What is the ip address of your router?
- What is the ip address of your PC?
- What is the ip address of your ant?
What I would suggest at this point is to do a hard reset by holding down the black button on the controller board. You can download the faq and manual files here:
https://github.com/AntMiner/AntGen1/tree/master/manualOnce you have done a reset back to factory settings, check to make sure all the cables are fitted snugly and turn it back on and see if it gives the same error in the log.
If you post a printout of the system and kernel logs it will also help.
Once you're done, fill in the answers to the questions and we'll go from there.
THANK YOU EVERYBODY, I'm now mining after a week of troubleshooting!!!
I had to make my ant's address 192.168.0.99 and gateway 192.168.0.1 (routers ip),
DNS 8.8.8.8, used NTP servers 0 through 3.us.pool.ntp.org
the last error was gone after I Factory reset it and reconfigured this third time
Pluged into router and pulled up gui, miner status------> 178.76 GH/s avg.
THANK YOU ALL
THANK YOU
--Nick
