Topic: [Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner - page 60. (Read 452359 times)

So a 1200 watt? I heard something about 12 V rail, is it fine to run 3 on a single rail? What PSU do you recommend to run 3 antminers, 2 lower end, or one higher end power supply?

NO, you can't.
3x 360w = 1080w

You can power two Ants though.

If I had a 1000w that had 6 6+2 pcie connectors, I could power 3? Would just have to supply the plugs and Ethernet?

If you have 2 6-pin pcie connectors, they just plug straight in... no need to butcher any cables, unless you don't have enough 6pin fittings from the psu.

Is there a way to do this without butchering 6 pins? I'm quite not getting how this goes...

I meant you'll have to switch the miner off... at the wall. I can't imagine why you'd want it running while not hashing.

Can you please explain me how to switch the beeping off ?

Bummer, sorry to hear, I'm sure that is very frustrating. I can't remember the trail to know where your problem started, so I'm just going to ask some questions:
 - Did the miner ever work i.e. has this error always been in the log?
 - Have you changed any of the network settings on the ant?
 - What is the ip address of your router?
 - What is the ip address of your PC?
 - What is the ip address of your ant?

What I would suggest at this point is to do a hard reset by holding down the black button on the controller board. You can download the faq and manual files here: https://github.com/AntMiner/AntGen1/tree/master/manual
Once you have done a reset back to factory settings, check to make sure all the cables are fitted snugly and turn it back on and see if it gives the same error in the log.
If you post a printout of the system and kernel logs it will also help.
Once you're done, fill in the answers to the questions and we'll go from there.

I don't think that's possible... if you want it to stop the beeping, you'll have to switch it off.

UP ...

Thanks everyone with the networking support but not there yet.
I now have the Antminer connected to the router via ethernet, it seems to be online and able to ping.
However I'm still not mining I think the problem is this:

Thu Mar 13 01:45:09 2014 kern.warn kernel: [   21.660000] PIC microchip bootloader usb OK
Thu Mar 13 01:45:09 2014 daemon.notice netifd: lan (647): Sending discover...
Thu Mar 13 01:45:09 2014 kern.info kernel: [   22.250000] br-wan: port 1(eth1) entered learning state
Thu Mar 13 01:45:09 2014 daemon.info sysinit: command failed: Device or resource busy (-16)
Thu Mar 13 01:45:09 2014 daemon.info sysinit: command failed: Device or resource busy (-16)
Thu Mar 13 01:45:10 2014 daemon.info sysinit: wpa_supplicant_setup_vif(wlan0): Refusing to bridge sta mode interface
Thu Mar 13 01:45:10 2014 daemon.info sysinit: enable_mac80211(radio0): Failed to set up wpa_supplicant for interface wlan0
Thu Mar 13 01:45:11 2014 kern.info kernel: [   24.250000] br-wan: topology change detected, propagating
Thu Mar 13 01:45:11 2014 kern.info kernel: [   24.250000] br-wan: port 1(eth1) entered forwarding state
Thu Mar 13 01:45:11 2014 daemon.info sysinit: wpa_supplicant_setup_vif(wlan0-1): Refusing to bridge sta mode interface
Thu Mar 13 01:45:11 2014 daemon.info sysinit: enable_mac80211(radio0): Failed to set up wpa_supplicant for interface wlan0-1
Thu Mar 13 01:45:12 2014 daemon.notice netifd: lan (647): Sending discover...
Thu Mar 13 01:45:18 2014 kern.warn kernel: [   31.240000] no int in filled

It also hangs at cgminer at the end:

Thu Mar 13 01:48:02 2014 cron.info crond[580]: crond: USER root pid 990 cmd /usr/bin/cgminer-monitor

Its been over a week and still no hashing please help!
Thanks,
--Nick

Check all your cables and make sure they are fitted snugly (turn it off first). From the temps on the second board it looks like those chips aren't getting any power at all.

Edit: you can also check for any loose capacitors on the second board, maybe some are broken.

It hasn't been necessary for a while now. Certainly a welcome change over the earlier revisions.

Just got a new S1 in the mail today.  It came pre-installed with PCI-e power connectors on the board.  It may no longer be necessary to buy PCI-e cables for these devices.

Bro if it powers up and you see lights coming on then it works.
You just need to set it up properly.

Just my opinion...
[/quote]

It's not my cherry, #21 it's just lame. Stuff happens.

Hello I need advise, I setup today 2nd miner from bitmain and on the miner status it is only 155GH/s ,

ASIC status
oooooooo oooooooo oooooooo oooooooo
xxxxxxxx oooooooo oooooooo oooooooo

tested with 2 psu working fine with other S1

not sure is that mean part of the S1 board is defective?


http://www.raspberrypirobot.com/s1problem.png

Paid a week ago, still not shipped

Order #100000872 - PAID

Seconded. I added a CoolerMaster JetFlo 120 as a second fan, an exhaust fan pulling the air through (it's not quite got a high enough CFM to operate on it's own), as a second fan it reduces the sensor reported temps by 3deg.

May I add that you could add another fan on the other side? 
It does help