Adrenalin 18.6.1, Windows 10 1803, 5xRX580 3xRX480
I'm currently stuck at "Initializing OpenCL devices, please wait.. ..." as long as I got my iGPU enabled, once I turn it off it works right away but I would prefer to keep it enabled.
Is there any way to fix this? Tried "--cgpuid 2,3,4....." with the correct bus id numbers and ignoring the iGPU but that also doesn't help
Topic: SRBMiner Cryptonight AMD GPU Miner V1.9.3 - native algo switching - page 121. (Read 237261 times)
October 23, 2018, 10:43:40 AM
October 23, 2018, 09:39:45 AM
Meh. I installed the older 18.5.1 driver, and it still doesn't help. It started promising with the secondary GPU spitting over 1200h/s, but the next report shows around 700 again… I could already see its gonna be a problem when in GPU-Z power consumption jumps between 60-140W, instead of being constant.
Big power and hashrate fluctuations are usually caused by too high intensity or too low power limit setting.
October 23, 2018, 08:54:10 AM
Meh. I installed the older 18.5.1 driver, and it still doesn't help. It started promising with the secondary GPU spitting over 1200h/s, but the next report shows around 700 again… I could already see its gonna be a problem when in GPU-Z power consumption jumps between 60-140W, instead of being constant.
October 23, 2018, 06:16:27 AM
whats the point of dealing with all this instability and extra heat from cnv8 when its less profitable atm than even eth.
hash rate is pretty much back to where it was 500ghs WTF lol
hash rate is pretty much back to where it was 500ghs WTF lol
Not happy with it either, XMR difficulty drop ending in a blink
Knocked off ASICs but it seems the difficulty drop attracted too many GPU farms to move away from ETH.
October 23, 2018, 04:26:18 AM
1 rig 4 x vega56 + 2 x rx570 9400hs 1040watts at the wall
All my rx 570s hashing exactly same on v8 940hs.
My rx 550s are at 450hs each
All my rx 570s hashing exactly same on v8 940hs.
My rx 550s are at 450hs each
which setting do you have for your rx570 and biosmod?
1180 core 860mv and 1950 memory 890mv.
Custom memory strap
For which card is these clocks, can you post your straps for RX550 ?
October 23, 2018, 01:31:38 AM
1 rig 4 x vega56 + 2 x rx570 9400hs 1040watts at the wall
All my rx 570s hashing exactly same on v8 940hs.
My rx 550s are at 450hs each
All my rx 570s hashing exactly same on v8 940hs.
My rx 550s are at 450hs each
which setting do you have for your rx570 and biosmod?
1180 core 860mv and 1950 memory 890mv.
Custom memory strap
October 23, 2018, 12:26:57 AM
Code:
C:\Latest cast_xmr-vega-win64_120>switch-radeon-gpu -G 1 --largepages=on --hbcc=off autorestart
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Switch Radeon GPU 0.9.5
Restart GPUs and switch 'Compute Mode', 'Large Pages' and 'HBCC memory'
on or off for example:
'switch-radeon-gpu -G 0 --compute=on restart'
Run with --help to list available optionss
Coded by [glph3k] for more info visit http://www.gandalph3000.com
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Detected OpenCL Platform: OpenCL 2.1 AMD-APP (2580.6)
GPU1: Radeon Vega Frontier Edition (gfx901) ... no changes.
GPU1: Radeon Vega Frontier Edition (gfx901) | HBCC: OFF | Large Pages: ON
C:\Latest cast_xmr-vega-win64_120>switch-radeon-gpu -G 1 --largepages=on --hbcc=off autorestart
Code:
2018-10-22 22:28:07] GPU0 : 1856 H/s [T: 55c, RPM: 2004, CC: 1474 MHz, MC: 920 MHz][BUS:20]
[2018-10-22 22:28:07] GPU1 : 1385 H/s [T: 55c, RPM: 4811, CC: 1408 MHz, MC: 1100 MHz][BUS:11]
[2018-10-22 22:28:07] GPU2 : 1933 H/s [T: 40c, RPM: 3887, CC: 1408 MHz, MC: 1100 MHz][BUS:8]
[2018-10-22 22:28:07] GPU3 : 1933 H/s [T: 42c, RPM: 4316, CC: 1408 MHz, MC: 1100 MHz][BUS:5]
[2018-10-22 22:28:07] GPU4 : 1832 H/s [T: 40c, RPM: 3033, CC: 1407 MHz, MC: 900 MHz][BUS:14]
[2018-10-22 22:28:07] GPU5 : 1350 H/s [T: 53c, RPM: 4803, CC: 1408 MHz, MC: 1100 MHz][BUS:17]
[2018-10-22 22:28:07] Total: 10289 H/s
[2018-10-22 22:28:07] Pool accepted result 0x000189B9
[2018-10-22 22:28:08] Pool accepted result 0x00004A03
se below 1350 max hash on both FEs , so damn anoying
October 23, 2018, 12:10:45 AM
Can someone help? When i start my miner at the very start my main GPU always crash.... i've change 2-3 different cards and the problem is still the same. Using 18.5.1 and 1803win edition. Anyone with same problem like me?
Try to use the integrated gpu on your mobo for main display.
If you havent integrated gpu try to decrease intencity on main GPU for about 25-30% or until it became stable.
My 7970 (tahiti) 1000/1500 1.2v driver 18.5.2
{ "id" : 0, "intensity" : 58, "worksize" : 16, "threads" : 1} almost stable, just couple reboots for a night). Now decrease intecity by 1. And yes, monitor plugged in to this card too. Almost 460 H/s.
October 22, 2018, 11:09:57 PM
whats the point of dealing with all this instability and extra heat from cnv8 when its less profitable atm than even eth.
hash rate is pretty much back to where it was 500ghs WTF lol
hash rate is pretty much back to where it was 500ghs WTF lol
October 22, 2018, 10:43:25 PM
Hello,
I got strange problem. Kind like pyramid problem, previous card always lower than next card.
[2018-10-22 17:56:05] GPU0 : 1512 H/s [T: 62c, RPM: 3673, CC: 1200 MHz, MC: 900 MHz][BUS:21] >> vega56
[2018-10-22 17:56:05] GPU1 : 1523 H/s [T: 68c, RPM: 3666, CC: 1050 MHz, MC: 800 MHz][BUS:18] >> vega56
[2018-10-22 17:56:05] GPU2 : 1698 H/s [T: 63c, RPM: 3693, CC: 1202 MHz, MC: 900 MHz][BUS:24] >> vega56
[2018-10-22 17:56:05] GPU3 : 1694 H/s [T: 62c, RPM: 3679, CC: 1350 MHz, MC: 950 MHz][BUS:15] >> vega56
[2018-10-22 17:56:05] GPU4 : 1969 H/s [T: 65c, RPM: 3698, CC: 1350 MHz, MC: 1100 MHz][BUS:9] >> vega64
[2018-10-22 17:56:05] Total: 8396 H/s
I'm using windows 10 1803 and 18.6.1 adrenalin driver.
I try even install clean windows etc still error like that. Anyone can help?
Thank you.
==
Oh I forgot to mention, i just lower my core for make it to stay below 70c, and even i make it same as other 1350 900, the problem still persist.
I got strange problem. Kind like pyramid problem, previous card always lower than next card.
[2018-10-22 17:56:05] GPU0 : 1512 H/s [T: 62c, RPM: 3673, CC: 1200 MHz, MC: 900 MHz][BUS:21] >> vega56
[2018-10-22 17:56:05] GPU1 : 1523 H/s [T: 68c, RPM: 3666, CC: 1050 MHz, MC: 800 MHz][BUS:18] >> vega56
[2018-10-22 17:56:05] GPU2 : 1698 H/s [T: 63c, RPM: 3693, CC: 1202 MHz, MC: 900 MHz][BUS:24] >> vega56
[2018-10-22 17:56:05] GPU3 : 1694 H/s [T: 62c, RPM: 3679, CC: 1350 MHz, MC: 950 MHz][BUS:15] >> vega56
[2018-10-22 17:56:05] GPU4 : 1969 H/s [T: 65c, RPM: 3698, CC: 1350 MHz, MC: 1100 MHz][BUS:9] >> vega64
[2018-10-22 17:56:05] Total: 8396 H/s
I'm using windows 10 1803 and 18.6.1 adrenalin driver.
I try even install clean windows etc still error like that. Anyone can help?
Thank you.
==
Oh I forgot to mention, i just lower my core for make it to stay below 70c, and even i make it same as other 1350 900, the problem still persist.
Your vegas temperature is too high.
If your core is 68c, HBM and Hotspot is 78c+. HBM and hotspots are always 10c higher than the core temperature.
This is very dangerous, Keep the HBM and Hotspot temperature below 68-72C.
[2018-10-23 10:40:35] Pool rejected result 0x000036FE (low difficulty share)
[2018-10-23 10:40:39] GPU0 : 1740 H/s [T: 58c, RPM: 3698, CC: 1200 MHz, MC: 900 MHz][BUS:21]
[2018-10-23 10:40:39] GPU1 : 1503 H/s [T: 63c, RPM: 3719, CC: 1050 MHz, MC: 800 MHz][BUS:18]
[2018-10-23 10:40:39] GPU2 : 1789 H/s [T: 59c, RPM: 3723, CC: 1202 MHz, MC: 900 MHz][BUS:24]
[2018-10-23 10:40:39] GPU3 : 1926 H/s [T: 62c, RPM: 3690, CC: 1350 MHz, MC: 950 MHz][BUS:15]
[2018-10-23 10:40:39] GPU4 : 2063 H/s [T: 57c, RPM: 3665, CC: 1350 MHz, MC: 1100 MHz][BUS:9]
[2018-10-23 10:40:39] Total: 9021 H/s
And before temp around 65-70 in hot days (at ver 7).
October 22, 2018, 10:20:47 PM
Nah, CF is disabled, as well as HBCC. I even went through the steps to enable the compute mode, but nothing helped.
You need 18.5.1 18.5.2 18.6.1 drivers.
Do not use 18.7.1+ drivers.
October 22, 2018, 10:16:41 PM
Hello,
I got strange problem. Kind like pyramid problem, previous card always lower than next card.
[2018-10-22 17:56:05] GPU0 : 1512 H/s [T: 62c, RPM: 3673, CC: 1200 MHz, MC: 900 MHz][BUS:21] >> vega56
[2018-10-22 17:56:05] GPU1 : 1523 H/s [T: 68c, RPM: 3666, CC: 1050 MHz, MC: 800 MHz][BUS:18] >> vega56
[2018-10-22 17:56:05] GPU2 : 1698 H/s [T: 63c, RPM: 3693, CC: 1202 MHz, MC: 900 MHz][BUS:24] >> vega56
[2018-10-22 17:56:05] GPU3 : 1694 H/s [T: 62c, RPM: 3679, CC: 1350 MHz, MC: 950 MHz][BUS:15] >> vega56
[2018-10-22 17:56:05] GPU4 : 1969 H/s [T: 65c, RPM: 3698, CC: 1350 MHz, MC: 1100 MHz][BUS:9] >> vega64
[2018-10-22 17:56:05] Total: 8396 H/s
I'm using windows 10 1803 and 18.6.1 adrenalin driver.
I try even install clean windows etc still error like that. Anyone can help?
Thank you.
==
Oh I forgot to mention, i just lower my core for make it to stay below 70c, and even i make it same as other 1350 900, the problem still persist.
I got strange problem. Kind like pyramid problem, previous card always lower than next card.
[2018-10-22 17:56:05] GPU0 : 1512 H/s [T: 62c, RPM: 3673, CC: 1200 MHz, MC: 900 MHz][BUS:21] >> vega56
[2018-10-22 17:56:05] GPU1 : 1523 H/s [T: 68c, RPM: 3666, CC: 1050 MHz, MC: 800 MHz][BUS:18] >> vega56
[2018-10-22 17:56:05] GPU2 : 1698 H/s [T: 63c, RPM: 3693, CC: 1202 MHz, MC: 900 MHz][BUS:24] >> vega56
[2018-10-22 17:56:05] GPU3 : 1694 H/s [T: 62c, RPM: 3679, CC: 1350 MHz, MC: 950 MHz][BUS:15] >> vega56
[2018-10-22 17:56:05] GPU4 : 1969 H/s [T: 65c, RPM: 3698, CC: 1350 MHz, MC: 1100 MHz][BUS:9] >> vega64
[2018-10-22 17:56:05] Total: 8396 H/s
I'm using windows 10 1803 and 18.6.1 adrenalin driver.
I try even install clean windows etc still error like that. Anyone can help?
Thank you.
==
Oh I forgot to mention, i just lower my core for make it to stay below 70c, and even i make it same as other 1350 900, the problem still persist.
Your vegas temperature is too high.
If your core is 68c, HBM and Hotspot is 78c+. HBM and hotspots are always 10c higher than the core temperature.
This is very dangerous, Keep the HBM and Hotspot temperature below 68-72C.
October 22, 2018, 09:47:07 PM
is this ok to have stale share like this?
-------------------------STATS-------------------------
Miner version: 1.6.8
Driver version: 24.20.11021.1000
Mining time: 1 days, 15 hours, 44 minutes, 39 seconds
Algo: normalv8
Pool: asia.cryptonight-hub.miningpoolhub.com:20580
Connected since: 2018-10-21 18:00:25
Pool Difficulty: 60020
Pool latency: ~174 ms
Last job received: 26 seconds ago
Accepted(Stale)/Total shares: 7819(587)/7819 (100.0%)
Average time to find share: 18 seconds
1 min. average speed: 2771 H/s
5 min. average speed: 2768 H/s
30 min. average speed: 2770 H/s
Max. speed: 2781 H/s
-------------------------STATS-------------------------
Miner version: 1.6.8
Driver version: 24.20.11021.1000
Mining time: 1 days, 15 hours, 44 minutes, 39 seconds
Algo: normalv8
Pool: asia.cryptonight-hub.miningpoolhub.com:20580
Connected since: 2018-10-21 18:00:25
Pool Difficulty: 60020
Pool latency: ~174 ms
Last job received: 26 seconds ago
Accepted(Stale)/Total shares: 7819(587)/7819 (100.0%)
Average time to find share: 18 seconds
1 min. average speed: 2771 H/s
5 min. average speed: 2768 H/s
30 min. average speed: 2770 H/s
Max. speed: 2781 H/s
October 22, 2018, 07:51:53 PM
Nah, CF is disabled, as well as HBCC. I even went through the steps to enable the compute mode, but nothing helped.
Remove driver using DDU twice, reinstall DRIVER ONLY without wattman etc etc
Disable crossfire, apply PPT. Enable large page. Enable compute mode.
Done. Now you have 160W/vega 56 out off the wall with 1900Hs on CN8
October 22, 2018, 06:19:24 PM
Nah, CF is disabled, as well as HBCC. I even went through the steps to enable the compute mode, but nothing helped.
October 22, 2018, 06:16:48 PM
Hello everyone. I had to register to ask this. After v8 forking I tried xmr-stak downloaded from nanopool, and even if I think I configured it correctly, and it mines, nothing appears in my wallet. I searched around and on my friend's recommendation I'm now running SRBminer. He even helped me configure it by using teamviewer. But when he tried using devcon it resulted in BSOD.
Anyways, I'm mining now and getting stuff on nanopool correctly. However, I'm using undervolted settings and one of my two Vega 64s (GPU0) mines as its expected, nearly 1800h/s. The second one (GPU1) is quite spastic, its not reaching even 700h/s... I'm using the latest 10.1 driver, and I'm on a Threadripper system. Any advice? I had these kinds of issues before on other miners earlier in the year, but can't quite pin it down.
Make sure you read the first post (and linked posts) carefully.Anyways, I'm mining now and getting stuff on nanopool correctly. However, I'm using undervolted settings and one of my two Vega 64s (GPU0) mines as its expected, nearly 1800h/s. The second one (GPU1) is quite spastic, its not reaching even 700h/s... I'm using the latest 10.1 driver, and I'm on a Threadripper system. Any advice? I had these kinds of issues before on other miners earlier in the year, but can't quite pin it down.
Maybe you haven't disabled crossfire or something. Such a big hashrate deficit is usually due to something specific that has been covered in the OP.
October 22, 2018, 04:32:16 PM
1 rig 4 x vega56 + 2 x rx570 9400hs 1040watts at the wall
All my rx 570s hashing exactly same on v8 940hs.
My rx 550s are at 450hs each
All my rx 570s hashing exactly same on v8 940hs.
My rx 550s are at 450hs each
how do you reach 450 with rx 550? what do you have in the config?
I don't buy it either. My best 560's max out at ~465 h/s.
I doubt the average 550 can do anything over 430 h/s, if it's real he must have crazy high mem oc and super aggressive timing straps.
October 22, 2018, 04:18:23 PM
Hello everyone. I had to register to ask this. After v8 forking I tried xmr-stak downloaded from nanopool, and even if I think I configured it correctly, and it mines, nothing appears in my wallet. I searched around and on my friend's recommendation I'm now running SRBminer. He even helped me configure it by using teamviewer. But when he tried using devcon it resulted in BSOD.
Anyways, I'm mining now and getting stuff on nanopool correctly. However, I'm using undervolted settings and one of my two Vega 64s (GPU0) mines as its expected, nearly 1800h/s. The second one (GPU1) is quite spastic, its not reaching even 700h/s... I'm using the latest 10.1 driver, and I'm on a Threadripper system. Any advice? I had these kinds of issues before on other miners earlier in the year, but can't quite pin it down.
Anyways, I'm mining now and getting stuff on nanopool correctly. However, I'm using undervolted settings and one of my two Vega 64s (GPU0) mines as its expected, nearly 1800h/s. The second one (GPU1) is quite spastic, its not reaching even 700h/s... I'm using the latest 10.1 driver, and I'm on a Threadripper system. Any advice? I had these kinds of issues before on other miners earlier in the year, but can't quite pin it down.
October 22, 2018, 03:02:56 PM
Running into trouble w/ SRBminer version 1.6.8 on my mining rig with 12 rx580 gpus (driver 8.15.1 or 8.16.1). Miner is now failing to start 1-3 gpus (gpus showing 0 hashes) after receiving jobs from pool. This was not a problem with SRB 1.6.7 on driver 18.3.4.
Miner works fine if I split into two jobs of 6 gpus, each. However, this messes with the algo switching. Anyone seeing anything similar or have a fix? Reducing intensity or reinstalling drivers doesn't work. Perhaps there's a timeout issue when attaching a larger number of GPUs under the latest drivers?
Log trace
[2018-10-20 15:00:54] json_receive: {"id":1,"jsonrpc":"2.0","error":null,"result":{"status":"OK"}}
[2018-10-20 15:00:54] miner_result: Pool accepted result 0x00000905
[2018-10-20 15:01:56] hashrate: GPU0: 0 H/s [BUS:1]
[2018-10-20 15:01:56] hashrate: GPU1: 828 H/s [BUS:2]
[2018-10-20 15:01:56] hashrate: GPU2: 834 H/s [BUS:3]
[2018-10-20 15:01:56] hashrate: GPU3: 830 H/s [BUS:4]
[2018-10-20 15:01:56] hashrate: GPU4: 830 H/s [BUS:5]
[2018-10-20 15:01:56] hashrate: GPU5: 829 H/s [BUS:6]
[2018-10-20 15:01:56] hashrate: GPU6: 828 H/s [BUS:9]
[2018-10-20 15:01:56] hashrate: GPU7: 1022 H/s [BUS:10]
[2018-10-20 15:01:56] hashrate: GPU8: 907 H/s [BUS:12]
[2018-10-20 15:01:56] hashrate: GPU9: 826 H/s [BUS:13]
[2018-10-20 15:01:56] hashrate: GPU10: 890 H/s [BUS:14]
[2018-10-20 15:01:56] hashrate: GPU11: 907 H/s [BUS:15]
[2018-10-20 15:01:56] hashrate: Total: 9531 H/s
[2018-10-20 15:02:11] watchdog: GPU0 [BUS: 1] hashing speed is 0 H/S
Miner works fine if I split into two jobs of 6 gpus, each. However, this messes with the algo switching. Anyone seeing anything similar or have a fix? Reducing intensity or reinstalling drivers doesn't work. Perhaps there's a timeout issue when attaching a larger number of GPUs under the latest drivers?
Log trace
[2018-10-20 15:00:54] json_receive: {"id":1,"jsonrpc":"2.0","error":null,"result":{"status":"OK"}}
[2018-10-20 15:00:54] miner_result: Pool accepted result 0x00000905
[2018-10-20 15:01:56] hashrate: GPU0: 0 H/s [BUS:1]
[2018-10-20 15:01:56] hashrate: GPU1: 828 H/s [BUS:2]
[2018-10-20 15:01:56] hashrate: GPU2: 834 H/s [BUS:3]
[2018-10-20 15:01:56] hashrate: GPU3: 830 H/s [BUS:4]
[2018-10-20 15:01:56] hashrate: GPU4: 830 H/s [BUS:5]
[2018-10-20 15:01:56] hashrate: GPU5: 829 H/s [BUS:6]
[2018-10-20 15:01:56] hashrate: GPU6: 828 H/s [BUS:9]
[2018-10-20 15:01:56] hashrate: GPU7: 1022 H/s [BUS:10]
[2018-10-20 15:01:56] hashrate: GPU8: 907 H/s [BUS:12]
[2018-10-20 15:01:56] hashrate: GPU9: 826 H/s [BUS:13]
[2018-10-20 15:01:56] hashrate: GPU10: 890 H/s [BUS:14]
[2018-10-20 15:01:56] hashrate: GPU11: 907 H/s [BUS:15]
[2018-10-20 15:01:56] hashrate: Total: 9531 H/s
[2018-10-20 15:02:11] watchdog: GPU0 [BUS: 1] hashing speed is 0 H/S
What do you mean by "if I split into two jobs of 6 gpus" ? Does it mean that it works when you split gpu's into two groups and run two instances of SRBMiner?
If so, we've even got a mixed rig of Vegas and RX580's to work with algo switching by having a different directory of configs for each group. It works with my rx580 rig too (which I created the test case). In our case I used my own proxy to handle the algo switching. Technique should work without the proxy but here's the link: https://github.com/hesido/cryptonote-switching-relay-proxy
What you do is, for each group of cards, have a separate config directory, algos text pointing to those different config directories, and a separate pool.txt. You can use a notepad++ to do file search and replace as necessary in the config directory for easier manipulation of the separate config texts.
This way, the rx580's hash at their max and vega's hash at their max, by hashing at the best algo which can be different.
October 22, 2018, 02:42:55 PM
i need vega 64 and vega 56 ppt regedit files. can someone help me?
Jump to: