Pages:
Author

Topic: [SUCCESS] 7 GPU Mining with Asrock H81 Pro BTC + PCIe Switch/Hub - page 3. (Read 29686 times)

sr. member
Activity: 544
Merit: 250
I do not understand, it does not work with me,

How did you do to install the 7gpu?

You install the 7 gpu and install driver after?

Or did you install driver with 1 gpu and then boot with the 7?

At home windows 10 recognizes the 7 gpu well, but when I run claymore I lose the driver. And i have bsod, and when i want to reboot it does not boot. Sad

Here are my steps:
1. Install the hardware of the PCIe splitter (only need power from molex or sata, not both) and GPU's and connect everything.
2. Boot into BIOS and change PCIE link speed to gen1.
3. Boot computer in safe mode.
4. Run DDU to install all old drivers from here http://www.guru3d.com/files-details/display-driver-uninstaller-download.html
5. Reboot computer normally.
6. It should show 7 gpu in device manager, if so, install drivers 16.9.1 (I have tested and it seems the most stable for me) http://support.amd.com/en-us/download/desktop/previous/detail?os=Windows%207%20-%2064&rev=16.9.1
7. Once driver's are installed, do not reboot computer. Download this and run it and modify registry https://lbr.id.lv/6xgpu_mod/
8. Now reboot, and everything should work.
sr. member
Activity: 487
Merit: 252
bou !
I do not understand, it does not work with me,

How did you do to install the 7gpu?

You install the 7 gpu and install driver after?

Or did you install driver with 1 gpu and then boot with the 7?

At home windows 10 recognizes the 7 gpu well, but when I run claymore I lose the driver. And i have bsod, and when i want to reboot it does not boot. Sad
sr. member
Activity: 465
Merit: 252
Wow this really awesome dude... I just finished a six card setup with same motherboard... Thx for sharing, Hey do you think putting an eighth card in that extra pcie slot you have there would work? Wattya think?

I wanted each port on my EVGA PSU to power each GPU individually, so it maxed out at 7 (No more ports available). Also, I am on a 20 amp breaker at 120v, so that is a max of 2400 watts. Two 7 gpu rigs combine is about 2000 watts already. That is about 83% load. If I try to add any more GPU, then it might be near the max of my 20 amp breaker and also wanted to give it some cushion too in case of spikes.

But if you really wanted me to give it a try, I can add a 8th card just for the heck of testing. But will need to find some time.

I understand your concerns, nevertheless it is still really impressive. Again thx for sharing!
hero member
Activity: 1498
Merit: 586
Hmm interested.

I will test.

What is this watttool tool?

It serves to modify the bios or is it a soft like msi after burner?

Watttool is kind of similar like MSI afterburner, but to me, I like WattTool better because I can change all the settings in a simple text .ini file and have it load at startup easily. I'm not much of a graphical interface kind of person when it comes to underclocking/overclocking. All the settings I need (voltage offset, GPU control, memory control, fan control, and etc) all in a plain text file easily for me to modify.


Hi Pikachuy. Are you using dummy plug? Any magic settings in BIOS? Thanks.

Yes, I am using a dummy plug as you can see from the pictures, only setting I changed was set PCIe to gen1, and disable onboard GPU.


Hello,

it's makerbeam or openbeam?

it work well your pci express 1 to 3 Huh

This is the case I got, http://spotswoodcomputercases.com/wp/?page_id=8791

wow very wonderful rig, hopefully someday im gonna build a rig like that. But it is too expensive, your videocards here in our country is very expensive like our electricity bill here is expensive too. But someday I wish I could have that too.
full member
Activity: 189
Merit: 100
Regarding cables:

Yes, I've always made cables. Been selling PSU breakout boards for a little over three years and they've always shipped with in-house-manufactured cables.

The cables I made for this build are 24" from EVGA 8-pin PCIe (and CPU) split to two PCIe 6+2. 18AWG wiring is necessary for doubling up in a pin (double 16AWG is too much wire for a solid reliable crimp) but that's still good for about 150W per end, meeting PCIe 8-pin spec.

Not sure if they're in use in this build but I also supplied some 6-pin to 4-Molex for riser power, plugging into the EVGA's SATA/RERP ports.

Yup, thanks for them. And yes, your cables are being used. Each riser and each GPU is independently powered from their own ports on the EVGA power supply, except for one port is powering 2 risers because of my 7 GPU set up (My powered risers are the 4 pin molex, I don't feel comfortable using those sata to molex adapters so I had sidehack make some molex ends for my PSU).

Here is a diagram of my setup in-case anyone else is interested:
(Note: Riser 5 is on a molex split because I needed a power source for my SSD.)

To save yourself some cabling in the future, you can split one power cable to two of your 480s easily.  I use a 6pin to dual 6+2 pin adapter and the builds are much cleaner.  Very nice job though.Smiley

So you've got 2 cards powered on a single pcie power line?

Yeah.  470/480s can do that pretty easily.  You just don't want to go above 300w total on a single pcie line.
sr. member
Activity: 544
Merit: 250
Wow this really awesome dude... I just finished a six card setup with same motherboard... Thx for sharing, Hey do you think putting an eighth card in that extra pcie slot you have there would work? Wattya think?

I wanted each port on my EVGA PSU to power each GPU individually, so it maxed out at 7 (No more ports available). Also, I am on a 20 amp breaker at 120v, so that is a max of 2400 watts. Two 7 gpu rigs combine is about 2000 watts already. That is about 83% load. If I try to add any more GPU, then it might be near the max of my 20 amp breaker and also wanted to give it some cushion too in case of spikes.

But if you really wanted me to give it a try, I can add a 8th card just for the heck of testing. But will need to find some time.
sr. member
Activity: 465
Merit: 252
Wow this really awesome dude... I just finished a six card setup with same motherboard... Thx for sharing, Hey do you think putting an eighth card in that extra pcie slot you have there would work? Wattya think?
sr. member
Activity: 544
Merit: 250
To save yourself some cabling in the future, you can split one power cable to two of your 480s easily.  I use a 6pin to dual 6+2 pin adapter and the builds are much cleaner.  Very nice job though.Smiley

Yea, I thought about that too, but then I wanted to future proof my rig, in case future cards require (2) 6pins or (2) 8pins each, then I am ready for them, just need to swap out the cards and good to go with no modification needed. Since right now, each GPU has a spare 6+2 PCIe as can been in the photos of the rear. I would hate having to redo my cables in the future if the newer cards requires more PCIe ends, which is the reason why i took this step.
full member
Activity: 189
Merit: 100
Regarding cables:

Yes, I've always made cables. Been selling PSU breakout boards for a little over three years and they've always shipped with in-house-manufactured cables.

The cables I made for this build are 24" from EVGA 8-pin PCIe (and CPU) split to two PCIe 6+2. 18AWG wiring is necessary for doubling up in a pin (double 16AWG is too much wire for a solid reliable crimp) but that's still good for about 150W per end, meeting PCIe 8-pin spec.

Not sure if they're in use in this build but I also supplied some 6-pin to 4-Molex for riser power, plugging into the EVGA's SATA/RERP ports.

Yup, thanks for them. And yes, your cables are being used. Each riser and each GPU is independently powered from their own ports on the EVGA power supply, except for one port is powering 2 risers because of my 7 GPU set up (My powered risers are the 4 pin molex, I don't feel comfortable using those sata to molex adapters so I had sidehack make some molex ends for my PSU).

Here is a diagram of my setup in-case anyone else is interested:
(Note: Riser 5 is on a molex split because I needed a power source for my SSD.)


To save yourself some cabling in the future, you can split one power cable to two of your 480s easily.  I use a 6pin to dual 6+2 pin adapter and the builds are much cleaner.  Very nice job though.Smiley
legendary
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
Cool. It's good to see everything working, took some figuring out to get the cable needs nailed down but it looks great.
sr. member
Activity: 544
Merit: 250
Regarding cables:

Yes, I've always made cables. Been selling PSU breakout boards for a little over three years and they've always shipped with in-house-manufactured cables.

The cables I made for this build are 24" from EVGA 8-pin PCIe (and CPU) split to two PCIe 6+2. 18AWG wiring is necessary for doubling up in a pin (double 16AWG is too much wire for a solid reliable crimp) but that's still good for about 150W per end, meeting PCIe 8-pin spec.

Not sure if they're in use in this build but I also supplied some 6-pin to 4-Molex for riser power, plugging into the EVGA's SATA/RERP ports.

Yup, thanks for them. And yes, your cables are being used. Each riser and each GPU is independently powered from their own ports on the EVGA power supply, except for one port is powering 2 risers because of my 7 GPU set up (My powered risers are the 4 pin molex, I don't feel comfortable using those sata to molex adapters so I had sidehack make some molex ends for my PSU).

Here is a diagram of my setup in-case anyone else is interested:
(Note: Riser 5 is on a molex split because I needed a power source for my SSD.)
legendary
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
Regarding cables:

Yes, I've always made cables. Been selling PSU breakout boards for a little over three years and they've always shipped with in-house-manufactured cables.

The cables I made for this build are 24" from EVGA 8-pin PCIe (and CPU) split to two PCIe 6+2. 18AWG wiring is necessary for doubling up in a pin (double 16AWG is too much wire for a solid reliable crimp) but that's still good for about 150W per end, meeting PCIe 8-pin spec.

Not sure if they're in use in this build but I also supplied some 6-pin to 4-Molex for riser power, plugging into the EVGA's SATA/RERP ports.
sr. member
Activity: 544
Merit: 250
I did exactly what you said, I think.

At startup windows wattTool loads automatically but it does not load my profin .ini

Hmm, thats odd, it should of, mine does. Maybe it might need a delay and some adjustment. Try changing your .bat file to this and let me know if it helped:
Code:
timeout 15
start WattTool-0.92.exe gpu1.ini

@pikachuy I love how you leveraged the modularity of the extrusions to mount the PCIe Switch/Hub.   Cool

What is the distance from the top of the motherboard, to the bottom of the USB risers?

Yea, I had to get creative, I did the same thing with the SSD drive, and just slide it down near the PSU, so it won't be dangling around. Everything sits nice and stable, even did a tilt/wobble test =)

The distance from the top of the motherboard to the bottom of the USB risers is about 4.5 inches.
sr. member
Activity: 512
Merit: 250
@pikachuy I love how you leveraged the modularity of the extrusions to mount the PCIe Switch/Hub.   Cool

What is the distance from the top of the motherboard, to the bottom of the USB risers?
newbie
Activity: 15
Merit: 0
Nice rig you got there. I could change the H81 PRO BTC for another 1150 with 6 pci x1? The H81 is really hard to find where I live.Ty Grin
sr. member
Activity: 487
Merit: 252
bou !
Quote
What I did was go on the first GPU in WattTool, and set up the settings to my liking, and then save profile, and then I go onto the next GPU and repeat, and save profiles (like GPU1.ini GPU2.ini GPU3.ini and etc.). Once that is all done for your GPUs, create a new text file in the WattTool folder named "Run.Bat". Then right click that new file and choose edit, and enter in something like this "WattTool-0.92.exe GPU1.ini GPU2.ini GPU3.ini GPU4.ini GPU5.ini GPU6.ini GPU7.ini" and save. Then right click that file and create shortcut. Now take that shortcut file and place it into your startup folder. Now when your computer boots up, it will load up all your profiles automatically. When ever I need to tweak stuff, I just make my changes and re-save the profiles to their appropriate name and it will still auto-load at startup

I did exactly what you said, I think.

At startup windows wattTool loads automatically but it does not load my profin .ini

sr. member
Activity: 544
Merit: 250
What processor are you using??

A basic Intel Pentium G3240
hero member
Activity: 1246
Merit: 708
What processor are you using??
legendary
Activity: 1096
Merit: 1021
Nice setup.  Just wondering what kind of PCIe cables those are and where did you get them.  I've been looking for some spare PCIe cables for EVGA power supplies.

I got my cables from sidehack, can see his thread here: https://bitcointalksearch.org/topic/fs-gs-server-psus-boards-kits-stickminers-gpu-riser-power-made-in-usa-940317

Great thanks!  I didn't realize he made cables as well.
Pages:
Jump to: