Pages:
Author

Topic: T17/S17 malfunction: cases, solutions, remedies, RMA history - page 19. (Read 7043 times)

legendary
Activity: 2394
Merit: 6581
be constructive or S.T.F.U
Then had another thought..... I initially assigned this unit a worker name for the pool that I had previously used for an old unit which I have since sold.  Dont know if that could cause confusion with the pool.

Depending on how the pool itself deals with these settings, it might cause the issue, but as far as I know, having two machines with the exact worker name online at the same time causes no problem, but it's possible that the worker had expired on the pool and no longer considered valid and thus the pool refuses it, this is why I like to use CKsolo pool as a second or third pool option since it requires no registration whatsoever, to me it's the most consistent pool, if it doesn't work, I rule out the pool problem.

Anyway, if the reg "crc error error" shows up again, it is still safe to assume that it's a connection issue, maybe your router/isp blocks the pool after a certain amount of packets if it shows up again, use DHCP settings on the miner, if it fails, use a public DNS like 8.8.8.8 and at last, try a different router.
full member
Activity: 414
Merit: 182
I'm at work now, I'll look into the network aspect tomorrow.

This unit is brand new.  Arrived 7 days ago.

And, 3 of my 5 units are still under warranty. So I'm only running factory firmware/settings while still covered.  So no overclocking for me. Also, I'm better with electrical than electronic, so I'm not comfortable messing with computer settings and programs I don't understand.   #OPP (Old People Problems).    BetaMax VCR was the height of my technical knowledge.


Edit:  
  So I swapped out the Ethernet cable, using a cable known to be working fine with another unit. Then had another thought..... I initially assigned this unit a worker name for the pool that I had previously used for an old unit which I have since sold.  Dont know if that could cause confusion with the pool.   Assigned it a completely new worker name not previously used.  
   Rebooted and so far we're ok.  We'll see for how long.  No crc reg error yet. It also read all the boards temp sensors correctly this time.
legendary
Activity: 2394
Merit: 6581
be constructive or S.T.F.U
I think this particulate error:

Code:
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error

Has to do with your internet connection or the pool itself, but since you tried a different pool then maybe a network problem, can you try to use DHCP settings and just to be safe, use a different ethernet cable.

Depending on how many gears you have, maybe overclocking them a bit will get your rate back to 6.8c ? also how long do you have for the warranty to be over? if not too long, maybe just void the warranty and send only the bad hashboard to Bitmain.
full member
Activity: 414
Merit: 182
Thats kinda the plan.  An extra 43TH is better than none.  Miner was almost "free" with the account credit I had at Bitmain.

And with the power plan (described in another post somewhere) that I have..... my price per kWh decreases with the extra power use.  Adding this miner dropped me from approx 7.2c to 6.8c.
legendary
Activity: 4256
Merit: 8551
'The right to privacy matters'
mine with it till a week after 1/2 ing then send it in under warranty.
full member
Activity: 414
Merit: 182
Well, thought I had my issue under control with the temp sensor error.  After multiple reboots, I reloaded the firmware. It ran a bit and threw the error.  Then ran almost a day before the error.  Ran another 3 days before the next error today.  Did a few reboots with no luck.

S17+ 70

So, being new, I plan to send it back for repair.

But the other thing thats getting me, that Ive never seen in any other miner is this error:

2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error

Whether it throws the temp sensor error or not..... I get that reg crc error.   Ive searched and cant find what it means. It will appear in the log hundreds of times, one after another.

I just did another reboot, this time pointing it at a new pool.  Dont see the reg crc error, but still giving me the temp sensor error on one board.

Edit:  nope.  Did another reboot an it came back.  So the pool had nothing to do with it.

Here's a little sampling:

Code:
et_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
2020-05-08 23:24:57 register.c:306:get_register: !!! reg crc error
legendary
Activity: 2394
Merit: 6581
be constructive or S.T.F.U
does their platform work for the latest Bitmain products as well?

Not sure what you mean by platform, if you are talking about the tools then you can browse their website, they have this tool works for all Bitmain Sha256 miners from T9 all the way to the latest 17 series.

Quote
I've used soldering equipment before and have the will do to hot air.

Here is a video tutorial for Antminer S9 https://www.youtube.com/watch?v=5WH7g61d90w&t=246s, fixing other versions will be nearly exactly the same, you will need the same tools, the only difference is that the chips models are different for certain miners, you can find all the tools in the video including the chips on their website or on aliexpress, the general tools can be found at any local shop near you, the chips and the fixture tools are special and only manufactured in China as far as I know.

Quote
Looks like I might have to replace a temperature sensor as well?

Nop, you don't have to, the chances of all 4 sensors stop working are slim to nothing, this error happens because of a bad chip, you can refer to this topic for more details regarding the temp sensors
newbie
Activity: 22
Merit: 26
Mikeywith,
I'm fully committed and I would like to try to fix it myself. I don't mind supporting zeusbtc, does their platform work for the latest Bitmain products as well? I've used soldering equipment before and have the will do to hot air.

Kernel Log:
Code:
** SAME AS Prior Post -  Deleted due to Forum Posting Limits **

2020-05-07 16:40:54 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 17862
2020-05-07 16:40:54 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 16993
2020-05-07 16:40:54 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 9242
2020-05-07 16:40:54 thread.c:478:clear_zero_nonce_mark: 0 nonce protect succeed.
2020-05-07 17:05:55 thread.c:204:calc_hashrate_avg: avg rate is 34688.48 in 30 mins
2020-05-07 17:05:55 temperature.c:450:temp_statistics_show:   pcb temp 40~56  chip temp 63~84
2020-05-07 17:05:55 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-07 17:05:55 thread.c:286:check_hashrate: current PCB min temperature 40
2020-05-07 17:05:55 thread.c:287:check_hashrate: current voltage is 17.10V, working voltage is 17.10V
2020-05-07 17:05:55 thread.c:318:check_hashrate: high temp, increase voltage 0.1V/0.2V to 17.20V
2020-05-07 17:05:55 driver-btm-api.c:2124:bitmain_reopen_core: reopen_core start!
2020-05-07 17:06:01 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-05-07 17:06:01 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-05-07 17:06:01 chain = 0, mode = 0, load_done = false.
2020-05-07 17:06:01 chain = 1, mode = 0, load_done = false.
2020-05-07 17:06:01 chain = 2, mode = 0, load_done = false.
2020-05-07 17:06:02 chain = 0, mode = 0, load_done = false.
2020-05-07 17:06:02 chain = 1, mode = 0, load_done = false.
2020-05-07 17:06:02 chain = 2, mode = 0, load_done = false.
2020-05-07 17:06:03 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-07 17:06:03 chain = 0, mode = 0, load_done = false.
2020-05-07 17:06:03 chain = 1, mode = 0, load_done = false.
2020-05-07 17:06:03 chain = 2, mode = 0, load_done = false.
2020-05-07 17:06:04 chain = 0, mode = 0, load_done = false.
2020-05-07 17:06:04 chain = 1, mode = 0, load_done = false.
2020-05-07 17:06:04 chain = 2, mode = 0, load_done = false.
2020-05-07 17:06:05 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-07 17:06:05 chain = 0, mode = 0, load_done = false.
2020-05-07 17:06:05 chain = 1, mode = 0, load_done = false.
2020-05-07 17:06:05 chain = 2, mode = 0, load_done = false.
2020-05-07 17:06:06 chain = 0, mode = 0, load_done = false.
2020-05-07 17:06:06 chain = 1, mode = 0, load_done = false.
2020-05-07 17:06:06 chain = 2, mode = 0, load_done = false.
2020-05-07 17:06:07 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-07 17:06:07 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-05-07 17:06:07 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-05-07 17:06:07 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-05-07 17:06:07 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-05-07 17:06:07 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-05-07 17:06:07 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-05-07 17:06:07 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-05-07 17:06:07 driver-btm-api.c:644:_set_project_type: project:2
2020-05-07 17:06:07 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-05-07 17:06:07 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-05-07 17:06:07 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-05-07 17:06:07 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-05-07 17:06:07 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-05-07 17:06:07 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-05-07 17:06:07 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-05-07 17:06:09 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-05-07 17:06:10 register.c:283:get_register: !!! reg crc error
2020-05-07 17:06:12 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-05-07 17:06:15 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-05-07 17:06:17 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-05-07 17:06:21 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-05-07 17:06:24 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-05-07 17:06:30 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-05-07 17:06:30 power_api.c:55:power_init: power init ...
2020-05-07 17:06:30 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-05-07 17:07:02 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-05-07 17:07:04 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 17:07:05 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.199638
2020-05-07 17:07:07 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.107793
2020-05-07 17:07:09 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.211885
2020-05-07 17:07:09 power_api.c:97:get_average_voltage: aveage voltage is: 17.173105
2020-05-07 17:07:09 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000
2020-05-07 17:07:09 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-07 17:07:09 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-07 17:07:09 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-07 17:07:09 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-07 17:07:19 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 29 asic, times 0
2020-05-07 17:07:29 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 1
2020-05-07 17:07:39 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-05-07 17:07:49 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-05-07 17:07:53 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-05-07 17:07:53 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-05-07 17:07:53 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-05-07 17:07:54 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-05-07 17:07:54 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-05-07 17:07:54 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-05-07 17:07:54 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-05-07 17:07:54 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-05-07 17:07:54 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-05-07 17:07:54 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-07 17:07:54 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-07 17:07:54 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-07 17:07:54 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-07 17:07:54 voltage[0] = 1710
2020-05-07 17:07:54 voltage[1] = 1710
2020-05-07 17:07:54 voltage[2] = 1710
2020-05-07 17:07:54 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-05-07 17:07:56 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-05-07 17:07:57 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-05-07 17:07:58 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-05-07 17:07:58 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-05-07 17:07:58 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-05-07 17:07:58 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-05-07 17:07:58 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-05-07 17:08:00 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 18
2020-05-07 17:08:00 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-05-07 17:08:00 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-05-07 17:08:36 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 17:08:38 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.142588
2020-05-07 17:08:40 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.118095
2020-05-07 17:08:41 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.228310
2020-05-07 17:08:41 power_api.c:97:get_average_voltage: aveage voltage is: 18.162998
2020-05-07 17:08:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-07 17:08:42 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-07 17:08:42 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-07 17:08:42 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-07 17:08:42 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-07 17:08:42 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-07 17:08:42 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-07 17:08:42 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-07 17:08:42 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-07 17:08:42 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-07 17:08:42 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-07 17:08:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-07 17:08:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-07 17:08:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-07 17:08:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-07 17:08:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-07 17:08:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-07 17:08:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-07 17:08:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-07 17:08:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-07 17:08:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-07 17:08:44 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-07 17:08:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-07 17:08:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-07 17:08:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-07 17:08:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-07 17:08:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-07 17:08:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-07 17:08:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-07 17:08:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-07 17:08:45 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-07 17:08:45 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-07 17:08:45 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-07 17:08:45 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-05-07 17:08:45 power_api.c:146:set_higher_voltage: higher_voltage = 18.000000
2020-05-07 17:08:45 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 18.00 ...
2020-05-07 17:09:09 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 17:09:11 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.111972
2020-05-07 17:09:13 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.099726
2020-05-07 17:09:15 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.209941
2020-05-07 17:09:15 power_api.c:97:get_average_voltage: aveage voltage is: 18.140547
2020-05-07 17:09:15 driver-btm-api.c:2186:bitmain_reopen_core: reopen_core done!
2020-05-07 17:09:15 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.20 ...
2020-05-07 17:09:16 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:09:16 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 109, reg = 226
2020-05-07 17:09:17 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:09:18 register.c:290:get_register: !!! REG_TYPE = 1. 718332418
2020-05-07 17:09:19 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:09:20 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:09:22 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 230, reg = 1
2020-05-07 17:09:23 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:09:23 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:09:26 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:09:26 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:09:29 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:09:29 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:09:40 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:09:40 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:09:42 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:09:42 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:09:55 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 17:09:56 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:09:56 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:09:57 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.260869
2020-05-07 17:09:59 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:09:59 register.c:290:get_register: !!! REG_TYPE = 1. 1634862082
2020-05-07 17:09:59 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:09:59 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.254746
2020-05-07 17:10:00 register.c:290:get_register: !!! REG_TYPE = 1. 962365698
2020-05-07 17:10:01 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.358838
2020-05-07 17:10:01 power_api.c:97:get_average_voltage: aveage voltage is: 17.291484
2020-05-07 17:10:01 power_api.c:140:set_working_voltage: working_voltage = 17.200001
2020-05-07 17:10:01 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 184, reg = 140
2020-05-07 17:10:02 register.c:290:get_register: !!! REG_TYPE = 1. 1219239938
2020-05-07 17:10:02 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:10:02 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:10:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:10:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:10:08 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 0, reg = 34
2020-05-07 17:10:08 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:10:08 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:10:11 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:10:11 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:10:14 register.c:290:get_register: !!! REG_TYPE = 1. 1024805634
2020-05-07 17:10:14 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:10:14 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:10:17 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:10:17 register.c:290:get_register: !!! REG_TYPE = 1. 2118170626
2020-05-07 17:10:17 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:10:20 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:10:20 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 0, reg = 128
2020-05-07 17:10:20 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:10:23 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:10:24 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:10:27 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 17:10:27 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 17:15:00 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 112336
2020-05-07 17:15:00 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 107640
2020-05-07 17:15:00 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 55208
2020-05-07 17:40:01 thread.c:204:calc_hashrate_avg: avg rate is 32945.16 in 30 mins
2020-05-07 17:40:01 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 61~80
2020-05-07 17:40:01 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-07 17:40:01 thread.c:286:check_hashrate: current PCB min temperature 42
2020-05-07 17:40:01 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-07 17:40:01 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V

** Deleted to meet Forum Posting Limit - Same as above but with temperature of 42 to 43 **

2020-05-07 19:45:47 register.c:290:get_register: !!! REG_TYPE = 1. 564257026
2020-05-07 19:45:50 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:45:50 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 144, reg = 131
2020-05-07 19:45:50 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:45:53 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:45:53 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:45:56 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:45:56 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:45:58 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:45:59 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:01 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:01 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:04 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:04 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:07 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:07 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:09 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:10 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:12 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 191, reg = 134
2020-05-07 19:46:12 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 105, reg = 123
2020-05-07 19:46:12 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:13 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:15 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:15 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:18 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:18 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:21 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:21 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:23 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 254, reg = 128
2020-05-07 19:46:23 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:24 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:26 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:26 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:29 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 106, reg = 56
2020-05-07 19:46:29 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:29 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:32 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:32 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:34 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:35 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:37 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 10, reg = 232
2020-05-07 19:46:37 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:37 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:40 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:40 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:43 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:43 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:45 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:46 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:48 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 161, reg = 213
2020-05-07 19:46:48 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:48 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:51 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:51 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 38, reg = 65
2020-05-07 19:46:51 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:54 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:54 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:46:57 register.c:290:get_register: !!! REG_TYPE = 1. 2146941442
2020-05-07 19:46:57 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:46:57 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:00 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:00 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 156, reg = 208
2020-05-07 19:47:00 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:02 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:02 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:05 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 16, reg = 212
2020-05-07 19:47:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:08 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:08 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:11 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:11 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:13 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:14 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:16 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:16 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:19 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:19 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:22 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:22 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:24 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:24 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:27 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:27 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 219, reg = 153
2020-05-07 19:47:27 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:30 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:30 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 30, reg = 93
2020-05-07 19:47:30 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:33 register.c:290:get_register: !!! REG_TYPE = 1. 1381375234
2020-05-07 19:47:33 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:33 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:35 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 140, reg = 183
2020-05-07 19:47:35 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:35 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:38 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:38 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:41 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 16, reg = 132
2020-05-07 19:47:41 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:41 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:43 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:44 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:46 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 5, reg = 8
2020-05-07 19:47:46 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:46 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:49 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:49 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:52 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:52 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:54 register.c:290:get_register: !!! REG_TYPE = 1. 1090715650
2020-05-07 19:47:54 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:54 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:47:57 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:47:57 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:00 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:00 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:03 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:03 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:08 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:08 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:11 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:11 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:14 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:14 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 81, reg = 152
2020-05-07 19:48:14 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:16 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:16 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:19 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:19 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 6, reg = 105
2020-05-07 19:48:19 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:22 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:22 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:25 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 0, reg = 0
2020-05-07 19:48:25 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:25 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 167, reg = 87
2020-05-07 19:48:25 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:27 register.c:290:get_register: !!! REG_TYPE = 1. 1610716674
2020-05-07 19:48:27 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:28 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 176, reg = 245
2020-05-07 19:48:28 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:30 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 137, reg = 3
2020-05-07 19:48:30 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:30 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:33 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:33 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:36 register.c:290:get_register: !!! REG_TYPE = 1. 1811939330
2020-05-07 19:48:36 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:36 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:39 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:39 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:41 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:41 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:44 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:44 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:47 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:47 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:50 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:50 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:52 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:53 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:55 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:55 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:48:58 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:48:58 register.c:290:get_register: !!! REG_TYPE = 1. 536901890
2020-05-07 19:48:58 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:01 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:01 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:03 register.c:290:get_register: !!! REG_TYPE = 1. 1627249410
2020-05-07 19:49:04 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:04 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:06 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:06 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 216, reg = 28
2020-05-07 19:49:07 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:09 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 94, reg = 45
2020-05-07 19:49:09 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:09 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:12 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:12 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:14 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:15 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:17 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:17 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:20 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 184, reg = 140
2020-05-07 19:49:20 register.c:290:get_register: !!! REG_TYPE = 1. 1179097602
2020-05-07 19:49:20 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:20 register.c:290:get_register: !!! REG_TYPE = 1. 1996685314
2020-05-07 19:49:20 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:23 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:23 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:26 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:26 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:28 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:28 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 184, reg = 140
2020-05-07 19:49:28 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:31 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:31 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:34 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:34 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 64, reg = 255
2020-05-07 19:49:34 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:37 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:37 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:39 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:40 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:42 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:42 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:45 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:45 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:48 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:48 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:51 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:51 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:53 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:54 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:56 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:56 register.c:290:get_register: !!! REG_TYPE = 1. 914804994
2020-05-07 19:49:56 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:49:59 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:49:59 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:02 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:02 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:05 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 147, reg = 93
2020-05-07 19:50:05 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 135, reg = 107
2020-05-07 19:50:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:08 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:08 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:10 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:11 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:13 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:13 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 125, reg = 216
2020-05-07 19:50:14 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:16 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 49, reg = 130
2020-05-07 19:50:16 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:16 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:19 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:19 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:22 register.c:290:get_register: !!! REG_TYPE = 1. 1879154946
2020-05-07 19:50:22 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:22 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 44, reg = 227
2020-05-07 19:50:22 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 17, reg = 188
2020-05-07 19:50:22 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 19, reg = 30
2020-05-07 19:50:22 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:25 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 25, reg = 131
2020-05-07 19:50:25 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:25 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 26, reg = 86
2020-05-07 19:50:25 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:28 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:28 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:31 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 144, reg = 1
2020-05-07 19:50:31 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:31 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:34 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 167, reg = 56
2020-05-07 19:50:34 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:34 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:36 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 4, reg = 180
2020-05-07 19:50:37 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:37 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:39 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:40 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:42 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:42 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:45 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:45 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 15, reg = 246
2020-05-07 19:50:45 register.c:290:get_register: !!! REG_TYPE = 1. 571650050
2020-05-07 19:50:45 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:48 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:48 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:51 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:51 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:53 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:54 register.c:160:read_asic_reg_with_addr: read asic reg error: expect chain = 2, chip = 184, reg = 28, got chain = 2, chip = 177, reg = 56
2020-05-07 19:50:54 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:56 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:56 register.c:290:get_register: !!! REG_TYPE = 1. 2069790466
2020-05-07 19:50:57 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:50:59 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:50:59 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:51:02 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:51:02 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:51:05 register.c:290:get_register: !!! REG_TYPE = 1. 816255490
2020-05-07 19:51:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:51:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:51:07 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:51:08 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:51:10 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:51:10 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:51:13 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:51:13 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 19:51:16 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 0
2020-05-07 19:51:16 temperature.c:697:get_temp_info: read temp sensor failed: chain = 2, sensor = 3, chip = 184, reg = 1
2020-05-07 20:10:07 thread.c:204:calc_hashrate_avg: avg rate is 32675.68 in 30 mins
2020-05-07 20:10:07 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 63~80
2020-05-07 20:10:07 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-07 20:10:07 thread.c:286:check_hashrate: current PCB min temperature 42
2020-05-07 20:10:07 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-07 20:10:07 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V

** DELETED due to Forum Posting Limit - Same as above and below but temperature 42 **

2020-05-07 23:10:15 thread.c:204:calc_hashrate_avg: avg rate is 32806.89 in 30 mins
2020-05-07 23:10:15 temperature.c:450:temp_statistics_show:   pcb temp 41~56  chip temp 60~79
2020-05-07 23:10:15 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-07 23:10:15 thread.c:286:check_hashrate: current PCB min temperature 41
2020-05-07 23:10:15 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-07 23:10:15 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-07 23:10:15 thread.c:238:is_domain_unbalance: Domain unbalance happened!
2020-05-07 23:10:15 driver-btm-api.c:201:set_miner_status: ERROR_UNBALANCE
2020-05-07 23:10:15 driver-btm-api.c:155:stop_mining_and_reboot: stop mining: Unbalance happened, reboot!

2020-05-07 23:10:15 thread.c:850:cancel_check_miner_status_thread: cancel thread
2020-05-07 23:10:15 thread.c:824:cancel_temperature_monitor_thread: cancel thread
2020-05-07 23:10:15 thread.c:834:cancel_read_nonce_reg_thread: cancel thread
2020-05-07 23:10:15 driver-btm-api.c:128:killall_hashboard: ****power off hashboard****
2020-05-07 23:10:20 Assert fail!! driver-btm-api.c:160: reboot

Looks like I might have to replace a temperature sensor as well?

Jacob
legendary
Activity: 2394
Merit: 6581
be constructive or S.T.F.U
This, without a doubt, is a bad hashboard, and by the way, boards showing 0 ASICs or anything less than what it should show (In this case 30 Asics) it's pretty normal to show all ASICs at some point, either after a reboot or when you move the board, here is a fun fact, many S9s boards I attempted to fix showed all Asics when I put the board on the table in a horizontal way, where the chips are sitting on the table, the moment I place them back in the miner vertically "standing", the board starts to act, sometimes it does mine well for a few days/weeks and then collapses again, sometimes by applying some pressure on the heatsinks I got some hashboards to work.

What you can conclude from the above is that some heatsinks/chips don't have perfect contact with the body of the hash board, so when they are cold, they seem to stick and contact, the board works, but when it gets hot, the heatsink/chip lose contact and errors start to show, in some cases and for whatever reason, the heatsink/chip does stick by itself and never show any errors again, but in most cases, it's only a matter of time till either the heatsink falls off the hashboard simply give you the same error.

So now my guess is that some chips/heatsinks on the hashboards are not in good contact, this is a common problem, in fact if you read the report coming in from the Chinese miners, one of the most common problem is what you are having now. If you want to investigate even further, you can buy Fluke 15b + f15b +, you can find it on Amazon too, but since you are going to be using the repair guide from zeusbtc, maybe it's a good idea to support them, but that's up to you of course, for now, you don't need the repair tools they sell, you can simply measure the resistance with the board unplugged, one or more chips will show some weird numbers, that will be a bad chip which needs replacement.

Replacing the chips is a whole different topic, but it's pretty doable if you have the tools, so if you plan on taking mining seriously and stacking more Bitmain gears, then it might be a good investment to buy all those tools, if not then just mine on with the board until it rest in peace.
newbie
Activity: 22
Merit: 26
1. The Kernel Log does look pretty different. No bad messages regarding temperature and such. So it's pointing to the Hashboard.

2. Back to the Original/PSU and problem Hashboard plugged in. The Kernal Log looks to have some of the re-occuring error messages. Too soon to for temperature messages, will let it run and post later. Funny thing is the Hashboard now recognizes all 30 chips and is running. Hashboard (Chain[2]) is operating a little higher now at a hashrate 60% of normal. As always it is showing all "oooo"'s for the chip status when the board does run. Very Strange and inconsistent when it works and doesn't but the errors and symptoms are the same.

Kernel Log:

Code:
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203756K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25620K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12580K (cceb8000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 4244297529
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 01559AD8-7B6A-42E6-A3FE-EDF3659527A9, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1054/342, WL threshold: 4096, image sequence number: 4185749592
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 4829CF2C-7435-4146-B2FD-0826AAE8443A, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2020-05-07 16:31:51 driver-btm-api.c:631:init_freq_mode: This is scan-user version
2020-05-07 16:31:51 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
2020-05-07 16:31:51 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
2020-05-07 16:31:51 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
2020-05-07 16:31:51 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
2020-05-07 16:31:51 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
2020-05-07 16:31:51 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
2020-05-07 16:31:51 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
2020-05-07 16:31:51 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-05-07 16:31:51 thread.c:789:create_read_nonce_reg_thread: create thread
2020-05-07 16:31:57 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-05-07 16:31:57 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-05-07 16:31:58 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-07 16:32:00 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-07 16:32:02 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-07 16:32:02 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-05-07 16:32:02 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-05-07 16:32:02 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-05-07 16:32:02 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-05-07 16:32:02 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-05-07 16:32:02 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-05-07 16:32:02 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-05-07 16:32:02 driver-btm-api.c:644:_set_project_type: project:2
2020-05-07 16:32:02 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-05-07 16:32:02 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-05-07 16:32:02 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-05-07 16:32:02 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-05-07 16:32:02 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-05-07 16:32:02 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-05-07 16:32:02 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-05-07 16:32:04 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-05-07 16:32:04 register.c:283:get_register: !!! reg crc error
2020-05-07 16:32:06 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-05-07 16:32:09 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-05-07 16:32:11 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-05-07 16:32:15 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-05-07 16:32:16 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-05-07 16:32:20 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-05-07 16:32:20 thread.c:784:create_pic_heart_beat_thread: create thread
2020-05-07 16:32:20 power_api.c:55:power_init: power init ...
2020-05-07 16:32:20 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-05-07 16:32:52 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-05-07 16:32:57 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 16:32:59 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.928281
2020-05-07 16:33:01 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.352715
2020-05-07 16:33:03 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.211885
2020-05-07 16:33:03 power_api.c:97:get_average_voltage: aveage voltage is: 17.497627
2020-05-07 16:33:03 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000
2020-05-07 16:33:03 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-07 16:33:03 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-07 16:33:03 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-07 16:33:03 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-07 16:33:14 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-05-07 16:33:24 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-05-07 16:33:34 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-05-07 16:33:38 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-05-07 16:33:38 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-05-07 16:33:38 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-05-07 16:33:38 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-05-07 16:33:39 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-05-07 16:33:39 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-05-07 16:33:39 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-05-07 16:33:39 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-05-07 16:33:39 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-05-07 16:33:39 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-07 16:33:39 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-07 16:33:39 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-07 16:33:39 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-07 16:33:39 voltage[0] = 1710
2020-05-07 16:33:39 voltage[1] = 1710
2020-05-07 16:33:39 voltage[2] = 1710
2020-05-07 16:33:39 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-05-07 16:33:41 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-05-07 16:33:42 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-05-07 16:33:43 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-05-07 16:33:43 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-05-07 16:33:43 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-05-07 16:33:43 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-05-07 16:33:43 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-05-07 16:33:45 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 17
2020-05-07 16:33:45 thread.c:804:create_check_miner_status_thread: create thread
2020-05-07 16:33:45 thread.c:794:create_set_miner_status_thread: create thread
2020-05-07 16:33:45 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-05-07 16:33:45 thread.c:779:create_temperature_monitor_thread: create thread
2020-05-07 16:33:45 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
2020-05-07 16:33:45 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-05-07 16:34:17 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 16:34:19 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.142588
2020-05-07 16:34:21 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.124219
2020-05-07 16:34:23 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.234433
2020-05-07 16:34:23 power_api.c:97:get_average_voltage: aveage voltage is: 18.167080
2020-05-07 16:34:23 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-07 16:34:23 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-07 16:34:23 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-07 16:34:23 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-07 16:34:23 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-07 16:34:23 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-07 16:34:23 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-07 16:34:24 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-07 16:34:24 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-07 16:34:24 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-07 16:34:24 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-07 16:34:24 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-07 16:34:24 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-07 16:34:24 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-07 16:34:24 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-07 16:34:24 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-07 16:34:24 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-07 16:34:25 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-07 16:34:25 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-07 16:34:25 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-07 16:34:25 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-07 16:34:25 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-07 16:34:25 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-07 16:34:25 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-07 16:34:25 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-07 16:34:25 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-07 16:34:26 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-07 16:34:26 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-07 16:34:26 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-07 16:34:26 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-07 16:34:26 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-07 16:34:26 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-07 16:34:26 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-07 16:34:26 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-05-07 16:34:26 power_api.c:146:set_higher_voltage: higher_voltage = 18.000000
2020-05-07 16:34:26 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 18.00 ...
2020-05-07 16:34:51 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 16:34:52 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.130342
2020-05-07 16:34:54 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.099726
2020-05-07 16:34:56 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.185449
2020-05-07 16:34:56 power_api.c:97:get_average_voltage: aveage voltage is: 18.138506
2020-05-07 16:34:56 frequency.c:540:get_current_min_freq: current min freq 670
2020-05-07 16:34:56 driver-btm-api.c:1660:check_clock_counter: freq 670 clock_counter_limit 85
2020-05-07 16:34:56 register.c:966:register_process_asic_response: Get another asic response: chain = 2, asic = 26
2020-05-07 16:34:56 register.c:1416:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 5, core = 1, found 1, clock counter 0x00000000
2020-05-07 16:34:56 driver-btm-api.c:2097:bitmain_soc_init: clock count check failed after retry, wait for hash rate protect later.
2020-05-07 16:34:56 thread.c:799:create_check_system_status_thread: create thread
2020-05-07 16:34:57 driver-btm-api.c:2113:bitmain_soc_init: Init done!
2020-05-07 16:34:57 driver-btm-api.c:201:set_miner_status: STATUS_INIT
2020-05-07 16:35:01 register.c:290:get_register: !!! REG_TYPE = 1. 1084936194
2020-05-07 16:35:02 register.c:290:get_register: !!! REG_TYPE = 1. 1090506754
2020-05-07 16:35:02 register.c:290:get_register: !!! REG_TYPE = 1. 1090506754
2020-05-07 16:35:02 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-05-07 16:35:07 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
2020-05-07 16:35:12 thread.c:382:check_working_voltage: current PCB min temperature is 41
2020-05-07 16:35:12 thread.c:383:check_working_voltage: current voltage is 18.00V, recovery to 17.10V
2020-05-07 16:35:12 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.10 ...
2020-05-07 16:35:50 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 16:35:51 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.187392
2020-05-07 16:35:53 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.162900
2020-05-07 16:35:55 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.279238
2020-05-07 16:35:55 power_api.c:97:get_average_voltage: aveage voltage is: 17.209844

Miner Status Screen: https://drive.google.com/file/d/1kXmiaOT-iP8L2mvQ9IGNY_JJVskctpEs/view?usp=sharing

Again Error Messages to note that didn't show up when the Hashboard in question (Chain [2]) was plugged in:

Code:
2020-05-07 16:34:56 register.c:966:register_process_asic_response: Get another asic response: chain = 2, asic = 26
2020-05-07 16:34:56 register.c:1416:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 5, core = 1, found 1, clock counter 0x00000000
2020-05-07 16:34:56 driver-btm-api.c:2097:bitmain_soc_init: clock count check failed after retry, wait for hash rate protect later.

2020-05-07 16:35:01 register.c:290:get_register: !!! REG_TYPE = 1. 1084936194
2020-05-07 16:35:02 register.c:290:get_register: !!! REG_TYPE = 1. 1090506754
2020-05-07 16:35:02 register.c:290:get_register: !!! REG_TYPE = 1. 1090506754

Jacob
newbie
Activity: 22
Merit: 26
Mikeywith, Update, Here is the kernel log with the original PSU and the Hashboard (Chain[2]) unplugged. No odd messages. Looks just like when it was run with the other PSU. I will now plug it the Hashboard in question and see what the logs say and post results.

Kernel Log:

Code:
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203756K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25620K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12580K (cceb8000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 4244297529
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 01559AD8-7B6A-42E6-A3FE-EDF3659527A9, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1053/342, WL threshold: 4096, image sequence number: 4185749592
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 4829CF2C-7435-4146-B2FD-0826AAE8443A, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2020-05-07 03:21:41 driver-btm-api.c:631:init_freq_mode: This is scan-user version
2020-05-07 03:21:41 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
2020-05-07 03:21:41 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
2020-05-07 03:21:41 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
2020-05-07 03:21:41 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
2020-05-07 03:21:41 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
2020-05-07 03:21:41 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
2020-05-07 03:21:41 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
2020-05-07 03:21:41 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-05-07 03:21:41 thread.c:789:create_read_nonce_reg_thread: create thread
2020-05-07 03:21:47 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-05-07 03:21:47 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-05-07 03:21:49 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-07 03:21:51 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-07 03:21:51 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-05-07 03:21:51 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-05-07 03:21:51 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-05-07 03:21:51 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-05-07 03:21:51 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-05-07 03:21:51 driver-btm-api.c:644:_set_project_type: project:2
2020-05-07 03:21:51 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-05-07 03:21:51 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-05-07 03:21:51 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-05-07 03:21:51 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-05-07 03:21:51 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-05-07 03:21:55 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-05-07 03:21:57 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-05-07 03:22:00 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-05-07 03:22:02 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-05-07 03:22:05 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-05-07 03:22:05 thread.c:784:create_pic_heart_beat_thread: create thread
2020-05-07 03:22:05 power_api.c:55:power_init: power init ...
2020-05-07 03:22:05 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-05-07 03:22:05 power_api.c:46:power_off: init gpio907
2020-05-07 03:22:37 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-05-07 03:22:39 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 03:22:41 power_api.c:86:get_average_voltage: chain[0], voltage is: 21.173496
2020-05-07 03:22:43 power_api.c:86:get_average_voltage: chain[1], voltage is: 20.420361
2020-05-07 03:22:43 power_api.c:97:get_average_voltage: aveage voltage is: 20.796928
2020-05-07 03:22:43 power_api.c:110:check_voltage: target_vol = 17.00, actural_vol = 20.80, more than 1.0v diff.
2020-05-07 03:22:44 power_api.c:124:check_voltage_multi: retry time: 1
2020-05-07 03:22:45 power_api.c:86:get_average_voltage: chain[0], voltage is: 19.416181
2020-05-07 03:22:47 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.797754
2020-05-07 03:22:47 power_api.c:97:get_average_voltage: aveage voltage is: 19.106968
2020-05-07 03:22:47 power_api.c:110:check_voltage: target_vol = 17.00, actural_vol = 19.11, more than 1.0v diff.
2020-05-07 03:22:48 power_api.c:124:check_voltage_multi: retry time: 2
2020-05-07 03:22:50 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.811943
2020-05-07 03:22:53 power_api.c:86:get_average_voltage: chain[1], voltage is: 16.868994
2020-05-07 03:22:53 power_api.c:97:get_average_voltage: aveage voltage is: 17.340469
2020-05-07 03:22:53 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000
2020-05-07 03:22:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-07 03:22:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-07 03:22:54 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-07 03:23:03 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-05-07 03:23:13 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-05-07 03:23:16 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-05-07 03:23:16 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-05-07 03:23:16 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-05-07 03:23:16 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-05-07 03:23:16 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-05-07 03:23:16 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-05-07 03:23:16 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-05-07 03:23:17 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-07 03:23:17 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-07 03:23:17 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-07 03:23:17 voltage[0] = 1710
2020-05-07 03:23:17 voltage[1] = 1710
2020-05-07 03:23:17 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-05-07 03:23:18 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-05-07 03:23:19 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-05-07 03:23:19 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-05-07 03:23:19 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-05-07 03:23:19 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-05-07 03:23:21 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 22
2020-05-07 03:23:21 thread.c:804:create_check_miner_status_thread: create thread
2020-05-07 03:23:21 thread.c:794:create_set_miner_status_thread: create thread
2020-05-07 03:23:21 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-05-07 03:23:21 thread.c:779:create_temperature_monitor_thread: create thread
2020-05-07 03:23:21 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
2020-05-07 03:23:21 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-05-07 03:23:50 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 03:23:51 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.142588
2020-05-07 03:23:53 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.118095
2020-05-07 03:23:53 power_api.c:97:get_average_voltage: aveage voltage is: 18.130342
2020-05-07 03:23:53 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-07 03:23:53 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-07 03:23:53 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-07 03:23:53 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-07 03:23:53 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-07 03:23:54 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-07 03:23:54 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-07 03:23:54 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-07 03:23:54 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-07 03:23:54 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-07 03:23:54 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-07 03:23:54 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-07 03:23:54 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-07 03:23:54 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-07 03:23:55 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-07 03:23:55 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-07 03:23:55 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-07 03:23:55 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-07 03:23:55 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-07 03:23:55 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-07 03:23:55 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-07 03:23:55 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-07 03:23:55 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-05-07 03:23:55 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.10 ...
2020-05-07 03:24:24 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-07 03:24:28 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.211885
2020-05-07 03:24:31 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.181269
2020-05-07 03:24:31 power_api.c:97:get_average_voltage: aveage voltage is: 17.196577
2020-05-07 03:24:31 frequency.c:540:get_current_min_freq: current min freq 670
2020-05-07 03:24:31 driver-btm-api.c:1660:check_clock_counter: freq 670 clock_counter_limit 85
2020-05-07 03:24:32 thread.c:799:create_check_system_status_thread: create thread
2020-05-07 03:24:33 driver-btm-api.c:2113:bitmain_soc_init: Init done!
2020-05-07 03:24:33 driver-btm-api.c:201:set_miner_status: STATUS_INIT
2020-05-07 03:24:38 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-05-07 03:24:47 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
2020-05-07 03:29:46 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 15323
2020-05-07 03:29:46 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 14616
2020-05-07 03:54:47 thread.c:204:calc_hashrate_avg: avg rate is 27676.36 in 29 mins
2020-05-07 03:54:47 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 67~80
2020-05-07 04:24:48 thread.c:204:calc_hashrate_avg: avg rate is 27736.35 in 30 mins
2020-05-07 04:24:48 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 67~80
2020-05-07 04:54:49 thread.c:204:calc_hashrate_avg: avg rate is 27372.68 in 30 mins
2020-05-07 04:54:49 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 67~80
2020-05-07 05:24:50 thread.c:204:calc_hashrate_avg: avg rate is 27682.71 in 30 mins
2020-05-07 05:24:50 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 67~80
2020-05-07 05:54:51 thread.c:204:calc_hashrate_avg: avg rate is 27730.27 in 30 mins
2020-05-07 05:54:51 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 67~80
2020-05-07 06:24:52 thread.c:204:calc_hashrate_avg: avg rate is 27587.18 in 30 mins
2020-05-07 06:24:52 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 67~80
2020-05-07 06:54:53 thread.c:204:calc_hashrate_avg: avg rate is 27575.03 in 30 mins
2020-05-07 06:54:53 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 07:24:54 thread.c:204:calc_hashrate_avg: avg rate is 27445.78 in 30 mins
2020-05-07 07:24:54 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 67~80
2020-05-07 07:54:54 thread.c:204:calc_hashrate_avg: avg rate is 27814.17 in 30 mins
2020-05-07 07:54:54 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 08:24:55 thread.c:204:calc_hashrate_avg: avg rate is 27621.68 in 30 mins
2020-05-07 08:24:55 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 08:54:56 thread.c:204:calc_hashrate_avg: avg rate is 27537.58 in 30 mins
2020-05-07 08:54:56 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 68~80
2020-05-07 09:24:57 thread.c:204:calc_hashrate_avg: avg rate is 27614.20 in 30 mins
2020-05-07 09:24:57 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 09:54:58 thread.c:204:calc_hashrate_avg: avg rate is 27766.82 in 30 mins
2020-05-07 09:54:58 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 10:24:59 thread.c:204:calc_hashrate_avg: avg rate is 27521.63 in 30 mins
2020-05-07 10:24:59 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 10:55:00 thread.c:204:calc_hashrate_avg: avg rate is 27584.10 in 30 mins
2020-05-07 10:55:00 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 11:25:01 thread.c:204:calc_hashrate_avg: avg rate is 27534.69 in 30 mins
2020-05-07 11:25:01 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 11:55:02 thread.c:204:calc_hashrate_avg: avg rate is 27889.86 in 30 mins
2020-05-07 11:55:02 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~81
2020-05-07 12:25:03 thread.c:204:calc_hashrate_avg: avg rate is 27751.13 in 30 mins
2020-05-07 12:25:03 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 68~81
2020-05-07 12:55:04 thread.c:204:calc_hashrate_avg: avg rate is 27353.70 in 30 mins
2020-05-07 12:55:04 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 13:25:05 thread.c:204:calc_hashrate_avg: avg rate is 27620.71 in 30 mins
2020-05-07 13:25:05 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 13:55:06 thread.c:204:calc_hashrate_avg: avg rate is 27397.21 in 30 mins
2020-05-07 13:55:06 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 14:25:07 thread.c:204:calc_hashrate_avg: avg rate is 27671.73 in 30 mins
2020-05-07 14:25:07 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 68~80
2020-05-07 14:55:08 thread.c:204:calc_hashrate_avg: avg rate is 27487.33 in 30 mins
2020-05-07 14:55:08 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-07 15:25:09 thread.c:204:calc_hashrate_avg: avg rate is 27426.67 in 30 mins
2020-05-07 15:25:09 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80

Miner Status Screen: https://drive.google.com/file/d/1e3O_gmv7yX_vPT0KGWFxJLt0LzlWGNot/view?usp=sharing

Jacob
legendary
Activity: 2394
Merit: 6581
be constructive or S.T.F.U

Ok the last thing to try now would be using the old psu with the bad hashboard unplugged ( completely removed ) and there will be 2 outcomes

1 - The temp error disappears and the kernel log looks very different to the first time  = psu is good but the board causes the errors sometimes.

2-  Kernel log goes back to the unusal temp and voltage readings = psu is bad, the bad hash board made things even worse.

And regardless of what happens, it is now safe to assume the hashboard is bad, maybe not completely dead but bad, the fact it shows 22 asics (if that doesn't change) it means either chip 22 or 23 is bad, after the psu swap you can put it back, perform a few restarts and see if it still shows exactly 22 chips, i will guide you on how to troubleshoot the bad chip and if you are willing to invest in some tools, i will tell you where to start with replacing the chips and where to buy them.
newbie
Activity: 22
Merit: 26
Mikeywith, Sorry, to be clear, I did not remove the hashboard it just stopped working altogether. All I did was remove and reconnect the cable to that hashboard. It has been connected everytime. Just that it is not registering all chips now. When powered on. The only change was the PSU. I never powered the miner without a hashboard.

Jacob
legendary
Activity: 2394
Merit: 6581
be constructive or S.T.F.U
Can they even tell the difference?

They can, and by doing so, you will void the warranty according to their reply to your question, you could still ask them, you lose nothing.

i think

"If the hashboard is sent separately, the whole machine can not be debugged. It is possible that the repaired hashboard can still not be used after being installed. The warranty will be lost if the hashboard is sent separately,  If you accept this risk, you can send it separately"

mysticbitcoin, the problem with that you did is that you changed two aspects at once, now the results may be very misleading, was the bad board causing the issue, or was it the psu? you removed the hashboard and replaced the PSU, the logs changed, in the end, the results are not satisfying, kindly put the bad hash board back and keep the new/working PSU.
legendary
Activity: 4256
Merit: 8551
'The right to privacy matters'
1 question to those who have sent units back to Bitmain for repair:


Can i switch the hash-boards from another machine? Both machines are at warranty, however one works with 2/3 and the other with 1/3 boards.

I am thinking to combine the non-working ones into the same unit and send them for repair. Do you think that this is possible?

Ask them first.

Most likely they will say no.

but you never know.

boards used to have serial numbers so you need to ask them if it is okay.
jr. member
Activity: 43
Merit: 59
1 question to those who have sent units back to Bitmain for repair:


Can i switch the hash-boards from another machine? Both machines are at warranty, however one works with 2/3 and the other with 1/3 boards.

I am thinking to combine the non-working ones into the same unit and send them for repair. Do you think that this is possible? Can they even tell the difference?
newbie
Activity: 22
Merit: 26
I also have a complete coorespondence with Bitmain tech support, Jessica L. I can post it if you guys are interested. All they have done is given me a generic trouble shooting list and not answered any of my specific questions.

Quote
Thanks for your consultation!

could you please try to exclude the issues by the below instructions

1.check the wires for the hashboard--pull them and re-plug them again, and also you can try to change the new wires
2.upgrade to the latest firmware
3. change the PSU to try it and reset the miner to the factory settings
4.flash the SD card program to recover the control board
the SD card program have be sent to you aby another email box, (also in your spam box)
instructions:
1 unzip the file we send to you
2After decompressing the card file, put all the below files into the card,
​​
3 insert it into the card slot of the control board,
4 and power on the control board

5 after the red and green lights blinks 3 or more times you can remove the SD card , it is ok


Please let us know if you have additional questions or concerns.

Jacob
newbie
Activity: 22
Merit: 26
UPDATE: PSU has been changed to a known good one. The Hashboard in question is now totally out of commission. The Board is only showing 22 Chips responding, I tried re-seating the cable as well as trying other cable from another good T17 Antminer. I have to make sure that it is the board that originally I thought it to be (one closest to the PSU). But I am at a loss. At this stage the Logs are not showing any of the High Temp messages and the PSU being set +0.10V to 17.20V to compensate. That maybe because the Controller has disabled the Hashboard in question and it is not instigating the temp issue. So what should I do next. This T17 was from July 2019 and so out of warranty. I need some advice and direction, and I'm willing to go all the way to repair the board myself.

Kernel Log:

Code:
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203756K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25620K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12580K (cceb8000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 4244297529
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 01559AD8-7B6A-42E6-A3FE-EDF3659527A9, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1052/341, WL threshold: 4096, image sequence number: 4185749592
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 4829CF2C-7435-4146-B2FD-0826AAE8443A, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2020-05-06 03:44:32 driver-btm-api.c:631:init_freq_mode: This is scan-user version
2020-05-06 03:44:32 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
2020-05-06 03:44:32 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
2020-05-06 03:44:32 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
2020-05-06 03:44:32 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
2020-05-06 03:44:32 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
2020-05-06 03:44:32 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
2020-05-06 03:44:32 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
2020-05-06 03:44:32 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-05-06 03:44:32 thread.c:789:create_read_nonce_reg_thread: create thread
2020-05-06 03:44:38 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-05-06 03:44:38 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-05-06 03:44:40 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-06 03:44:42 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-06 03:44:44 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-06 03:44:44 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-05-06 03:44:44 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-05-06 03:44:44 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-05-06 03:44:44 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-05-06 03:44:44 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-05-06 03:44:44 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-05-06 03:44:44 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-05-06 03:44:44 driver-btm-api.c:644:_set_project_type: project:2
2020-05-06 03:44:44 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-05-06 03:44:44 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-05-06 03:44:44 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-05-06 03:44:44 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-05-06 03:44:44 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-05-06 03:44:44 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-05-06 03:44:44 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-05-06 03:44:46 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-05-06 03:44:47 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-05-06 03:44:51 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-05-06 03:44:53 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-05-06 03:44:56 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-05-06 03:44:58 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-05-06 03:45:01 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-05-06 03:45:01 thread.c:784:create_pic_heart_beat_thread: create thread
2020-05-06 03:45:01 power_api.c:55:power_init: power init ...
2020-05-06 03:45:01 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-05-06 03:45:01 power_api.c:46:power_off: init gpio907
2020-05-06 03:45:33 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-05-06 03:45:39 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-06 03:45:41 power_api.c:86:get_average_voltage: chain[0], voltage is: 21.246972
2020-05-06 03:45:43 power_api.c:86:get_average_voltage: chain[1], voltage is: 20.573437
2020-05-06 03:45:44 power_api.c:86:get_average_voltage: chain[2], voltage is: 20.040732
2020-05-06 03:45:44 power_api.c:97:get_average_voltage: aveage voltage is: 20.620381
2020-05-06 03:45:44 power_api.c:110:check_voltage: target_vol = 17.00, actural_vol = 20.62, more than 1.0v diff.
2020-05-06 03:45:45 power_api.c:124:check_voltage_multi: retry time: 1
2020-05-06 03:45:47 power_api.c:86:get_average_voltage: chain[0], voltage is: 19.012060
2020-05-06 03:45:49 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.405879
2020-05-06 03:45:52 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.554775
2020-05-06 03:45:52 power_api.c:97:get_average_voltage: aveage voltage is: 18.324238
2020-05-06 03:45:52 power_api.c:110:check_voltage: target_vol = 17.00, actural_vol = 18.32, more than 1.0v diff.
2020-05-06 03:45:53 power_api.c:124:check_voltage_multi: retry time: 2
2020-05-06 03:45:55 power_api.c:86:get_average_voltage: chain[0], voltage is: 16.568965
2020-05-06 03:45:58 power_api.c:86:get_average_voltage: chain[1], voltage is: 15.681123
2020-05-06 03:46:00 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.383330
2020-05-06 03:46:00 power_api.c:97:get_average_voltage: aveage voltage is: 16.544472
2020-05-06 03:46:00 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000
2020-05-06 03:46:00 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-06 03:46:00 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-06 03:46:00 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-06 03:46:00 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-06 03:46:10 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-05-06 03:46:20 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-05-06 03:46:31 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 22 asic, times 0
2020-05-06 03:46:41 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 22 asic, times 1
2020-05-06 03:46:51 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 22 asic, times 2
2020-05-06 03:46:51 driver-btm-api.c:1037:check_asic_number: Chain 2 only find 22 asic, will power off hash board 2
2020-05-06 03:46:55 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-05-06 03:46:55 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-05-06 03:46:55 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-05-06 03:46:55 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-05-06 03:46:55 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-05-06 03:46:55 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-05-06 03:46:55 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-05-06 03:46:56 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-06 03:46:56 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-06 03:46:56 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-06 03:46:56 voltage[0] = 1710
2020-05-06 03:46:56 voltage[1] = 1710
2020-05-06 03:46:56 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-05-06 03:46:57 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-05-06 03:46:59 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-05-06 03:46:59 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-05-06 03:46:59 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-05-06 03:46:59 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-05-06 03:47:00 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 18
2020-05-06 03:47:00 thread.c:804:create_check_miner_status_thread: create thread
2020-05-06 03:47:00 thread.c:794:create_set_miner_status_thread: create thread
2020-05-06 03:47:00 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-05-06 03:47:00 thread.c:779:create_temperature_monitor_thread: create thread
2020-05-06 03:47:00 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
2020-05-06 03:47:00 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-05-06 03:47:29 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-06 03:47:30 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.154834
2020-05-06 03:47:32 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.142588
2020-05-06 03:47:32 power_api.c:97:get_average_voltage: aveage voltage is: 18.148711
2020-05-06 03:47:32 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-06 03:47:32 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-06 03:47:32 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-06 03:47:32 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-06 03:47:33 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-06 03:47:33 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-06 03:47:33 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-06 03:47:33 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-06 03:47:33 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-06 03:47:33 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-06 03:47:33 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-06 03:47:33 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-06 03:47:33 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-06 03:47:34 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-06 03:47:34 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-06 03:47:34 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-06 03:47:34 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-06 03:47:34 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-06 03:47:34 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-06 03:47:34 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-06 03:47:34 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-06 03:47:34 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-06 03:47:34 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-05-06 03:47:34 power_api.c:146:set_higher_voltage: higher_voltage = 18.000000
2020-05-06 03:47:34 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 18.00 ...
2020-05-06 03:47:56 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-06 03:47:58 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.167080
2020-05-06 03:47:59 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.118095
2020-05-06 03:47:59 power_api.c:97:get_average_voltage: aveage voltage is: 18.142588
2020-05-06 03:47:59 frequency.c:540:get_current_min_freq: current min freq 670
2020-05-06 03:47:59 driver-btm-api.c:1660:check_clock_counter: freq 670 clock_counter_limit 85
2020-05-06 03:48:01 thread.c:799:create_check_system_status_thread: create thread
2020-05-06 03:48:01 driver-btm-api.c:2113:bitmain_soc_init: Init done!
2020-05-06 03:48:01 driver-btm-api.c:201:set_miner_status: STATUS_INIT
2020-05-06 03:48:06 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-05-06 03:48:11 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
2020-05-06 03:48:15 thread.c:382:check_working_voltage: current PCB min temperature is 42
2020-05-06 03:48:15 thread.c:383:check_working_voltage: current voltage is 18.00V, recovery to 17.10V
2020-05-06 03:48:15 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.10 ...
2020-05-06 03:48:44 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-06 03:48:47 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.242500
2020-05-06 03:48:50 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.199638
2020-05-06 03:48:50 power_api.c:97:get_average_voltage: aveage voltage is: 17.221069
2020-05-06 03:53:50 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 17465
2020-05-06 03:53:50 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 16602
2020-05-06 04:18:50 thread.c:204:calc_hashrate_avg: avg rate is 27453.74 in 30 mins
2020-05-06 04:18:50 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 66~80
2020-05-06 04:48:51 thread.c:204:calc_hashrate_avg: avg rate is 27530.55 in 30 mins
2020-05-06 04:48:51 temperature.c:450:temp_statistics_show:   pcb temp 43~56  chip temp 66~80
2020-05-06 05:18:52 thread.c:204:calc_hashrate_avg: avg rate is 27760.23 in 30 mins
2020-05-06 05:18:52 temperature.c:450:temp_statistics_show:   pcb temp 43~56  chip temp 66~80
2020-05-06 05:48:53 thread.c:204:calc_hashrate_avg: avg rate is 27631.15 in 30 mins
2020-05-06 05:48:53 temperature.c:450:temp_statistics_show:   pcb temp 43~56  chip temp 66~80
2020-05-06 06:18:54 thread.c:204:calc_hashrate_avg: avg rate is 27378.79 in 30 mins
2020-05-06 06:18:54 temperature.c:450:temp_statistics_show:   pcb temp 43~56  chip temp 66~80
2020-05-06 06:48:55 thread.c:204:calc_hashrate_avg: avg rate is 27575.81 in 30 mins
2020-05-06 06:48:55 temperature.c:450:temp_statistics_show:   pcb temp 44~57  chip temp 67~80
2020-05-06 07:18:56 thread.c:204:calc_hashrate_avg: avg rate is 27259.51 in 30 mins
2020-05-06 07:18:56 temperature.c:450:temp_statistics_show:   pcb temp 44~57  chip temp 67~80
2020-05-06 07:48:57 thread.c:204:calc_hashrate_avg: avg rate is 27632.78 in 30 mins
2020-05-06 07:48:57 temperature.c:450:temp_statistics_show:   pcb temp 44~57  chip temp 66~81
2020-05-06 08:18:58 thread.c:204:calc_hashrate_avg: avg rate is 27501.75 in 30 mins
2020-05-06 08:18:58 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 67~80
2020-05-06 08:48:59 thread.c:204:calc_hashrate_avg: avg rate is 27580.74 in 30 mins
2020-05-06 08:48:59 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 67~80
2020-05-06 09:19:00 thread.c:204:calc_hashrate_avg: avg rate is 27439.63 in 30 mins
2020-05-06 09:19:00 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 67~80
2020-05-06 09:49:01 thread.c:204:calc_hashrate_avg: avg rate is 27474.81 in 30 mins
2020-05-06 09:49:01 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 67~80
2020-05-06 10:19:02 thread.c:204:calc_hashrate_avg: avg rate is 27385.07 in 30 mins
2020-05-06 10:19:02 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 67~80
2020-05-06 10:49:03 thread.c:204:calc_hashrate_avg: avg rate is 27453.96 in 30 mins
2020-05-06 10:49:03 temperature.c:450:temp_statistics_show:   pcb temp 44~57  chip temp 67~80
2020-05-06 11:19:04 thread.c:204:calc_hashrate_avg: avg rate is 27575.16 in 30 mins
2020-05-06 11:19:04 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 67~80
2020-05-06 11:49:05 thread.c:204:calc_hashrate_avg: avg rate is 27357.69 in 30 mins
2020-05-06 11:49:05 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-06 12:19:05 thread.c:204:calc_hashrate_avg: avg rate is 27594.36 in 30 mins
2020-05-06 12:19:05 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 67~80
2020-05-06 12:49:06 thread.c:204:calc_hashrate_avg: avg rate is 27735.40 in 30 mins
2020-05-06 12:49:06 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 67~80
2020-05-06 13:19:07 thread.c:204:calc_hashrate_avg: avg rate is 27537.99 in 30 mins
2020-05-06 13:19:07 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 68~80
2020-05-06 13:49:08 thread.c:204:calc_hashrate_avg: avg rate is 27652.88 in 30 mins
2020-05-06 13:49:08 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-06 14:19:09 thread.c:204:calc_hashrate_avg: avg rate is 27269.65 in 30 mins
2020-05-06 14:19:09 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 68~81
2020-05-06 14:49:10 thread.c:204:calc_hashrate_avg: avg rate is 27399.37 in 30 mins
2020-05-06 14:49:10 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 68~80
2020-05-06 15:19:11 thread.c:204:calc_hashrate_avg: avg rate is 27543.52 in 30 mins
2020-05-06 15:19:11 temperature.c:450:temp_statistics_show:   pcb temp 45~56  chip temp 68~80
2020-05-06 15:49:12 thread.c:204:calc_hashrate_avg: avg rate is 27670.96 in 30 mins
2020-05-06 15:49:12 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 66~79
2020-05-06 16:19:13 thread.c:204:calc_hashrate_avg: avg rate is 27272.62 in 30 mins
2020-05-06 16:19:13 temperature.c:450:temp_statistics_show:   pcb temp 41~56  chip temp 64~80
2020-05-06 16:49:14 thread.c:204:calc_hashrate_avg: avg rate is 27570.06 in 30 mins
2020-05-06 16:49:14 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 66~81
2020-05-06 17:19:15 thread.c:204:calc_hashrate_avg: avg rate is 27402.72 in 30 mins
2020-05-06 17:19:15 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 65~80

Miner Status Screen: https://drive.google.com/file/d/16g9lWAe2jJXcNo01baSYgOBN_od4_n2Z/view?usp=sharing

Log Shows:

Code:
2020-05-06 03:46:31 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 22 asic, times 0
2020-05-06 03:46:41 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 22 asic, times 1
2020-05-06 03:46:51 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 22 asic, times 2
2020-05-06 03:46:51 driver-btm-api.c:1037:check_asic_number: Chain 2 only find 22 asic, will power off hash board 2

Jacob
jr. member
Activity: 43
Merit: 59
If you decide to go for RMA, on all the new models you MUST ship the WHOLE miner, you might get lucky enough to be asked to ship only the bad part such as a hash board

I asked them if i could send only the hash boards. Here is their response:

"If the hashboard is sent separately, the whole machine can not be debugged. It is possible that the repaired hashboard can still not be used after being installed. The warranty will be lost if the hashboard is sent separately,  If you accept this risk, you can send it separately"
legendary
Activity: 2394
Merit: 6581
be constructive or S.T.F.U
Without being 100% sure the PSU is not causing the issue, all we can do is speculate, and since the miner does power up, it means the PSU isn't complelty dead, simply something is wrong with it, so it would work one time and fail at another, as for the temperature the kernel log shows

2020-05-05 21:00:36 temperature.c:450:temp_statistics_show:   pcb temp 41~56  chip temp 57~80

Antminer T17 has a max pcb temp of 75, your gear is 20 degrees far from that, also suspecting the PSU being the underlying cause of all this, doesn't negate the fact that chain 2 might be "dying" and is causing all the issues, you could disconnect chain 2 to see if the miner acts differently, but the proper way of troubleshooting IMO is top to bottom, you start with the PSU, Control Board, Network Cable, Wiring and etc. and THEN dig deeper into each hashbarods, you might think that there is no difference between the two approaches, but there is, there is a chance that your PSU is not able to supply enough power to all 3 boards despite that fact that all 3 boards are good, so you remove chain 2, everything looks great and you think your PSU is fine and board is bad when the fact is the exact the opposite.
Pages:
Jump to: