Topic: Team Black Miner (ETHW ETC Vertcoin Ravencoin Zilliqa +dual +tripple mining ) - page 72. (Read 35100 times)
October 28, 2021, 02:54:26 AM
@_Mauy Exact same issue here, thought I was alone
October 28, 2021, 02:46:51 AM
TBMv20 hiveos - cards are mining, but they are not showing in hiveos api.
I'm waiting for v21.
I'm waiting for v21.
October 28, 2021, 12:13:00 AM
I am using SSL on both Trex and TBM.
SSL have known issues. you should use the normal port
But pool side the rate 20-40% less after a couple 6 hour tests. Around 1% stales which are paid at 80%.
I get around +5% in tbm poolside vs T-rex, so something is wrong in your setup. Mine on high intensity.. epoc 450 can never give you 32Mhash on the gtx 1070. Normally 25-29mhash.
Is there any benefit to adding this parameter with a high xintensity value on RTX 30XX cards in 2Miners?
You can increase the speed with higher intensity. Why don't you try it out. What numbers are you getting?
--xintensity 224 (default)
--xintensity 256
--xintensity 288
--xintensity 320
.
.
.
[moderator's note: consecutive posts merged]
October 27, 2021, 09:43:14 PM
Thanks, I'll test these values.
What about --dagintensity ?
What about --dagintensity ?
Since the verification code doesn't fail, you don't need to use this. But you could use to increase the memory clock and put --dagintensity 0. This option is for rtx 3060ti,3070,3080 with extreme clocks. But you seem to be happy with 102MHASH. Higher clocks higher power needed.
Is there any benefit to adding this parameter with a high xintensity value on RTX 30XX cards in 2Miners?
October 27, 2021, 07:17:45 PM
This miner reports high numbers but at the pool its much lower than Trex.
I also use T-rex and having this issue as well, tried low default and high intensity and kernels.Client side is 32mh~ the highest Ive seen and client pool rate says higher than that usually.
But pool side the rate 20-40% less after a couple 6 hour tests. Around 1% stales which are paid at 80%.
T-rex is about 29.5MH but poolside is exactly that as well.
This is on a 1070 setup Linux latest drivers and version plus older ones.
I am using SSL on both Trex and TBM.
Could SSL or something else make that much of a difference on TBM but not Trex?
I need to try other pools.
October 27, 2021, 05:48:50 PM
Fixed The issue,
Thank you guys, Happy mining ⚒ everyone
- Newer Driver installed 470.82.00
- Added --api-port 64068
Thank you guys, Happy mining ⚒ everyone
October 27, 2021, 05:27:03 PM
Others have managed to run 1.20 without any problems. 1.20 was released a few hours ago, why don't you wait until hiveos add it.
wanted to test --dagintensity
October 27, 2021, 05:14:16 PM
Others have managed to run 1.20 without any problems. 1.20 was released a few hours ago, why don't you wait until hiveos add it.
October 27, 2021, 05:14:06 PM
470.74 is not the latest. this driver only support cuda 11.3
this is the latest available on HiveOS, used : nvidia-driver-update --list and it was latest one in the list
latest driver version is 470.82 , you can update using this command
nvidia-driver-update https://us.download.nvidia.com/XFree86/Linux-x86_64/470.82.00/NVIDIA-Linux-x86_64-470.82.00.run
Have you tested this driver? I have RTX 3xxx Cards, I need to make sure not miss with rig, its located far away from me.
Actually looking at the image you provided unless you are running an asic you might need to update hiveos altogether as seem to run an old version.
Newest version is [email protected]
October 27, 2021, 05:11:44 PM
I am not mining to ethermine, I am mining @ 2miners pool. please check screenshot attached
https://i.imgur.com/CbHQS6V.png
https://i.imgur.com/CbHQS6V.png
Upgrade the driver to the latest
https://github.com/sp-hash/TeamBlackMiner/issues/78
I have Latest Drivers installed :
N 470.74
Drivers
The only thing done, is that I manually replaced 1.19 to 1.20 by using commands in bash. may be something went wrong or I miss to do something while replacing 1.19 ?
add this line in miner.config --api-port 64068
Didnt help, still nothing. let me try replace 1.19 Back and check the results, seems issue in 1.20 !!
https://imgur.com/a/osTe3xy
470.74 is not the latest. this driver only support cuda 11.3
this is the latest available on HiveOS, used : nvidia-driver-update --list and it was latest one in the list
latest driver version is 470.82 , you can update using this command
nvidia-driver-update https://us.download.nvidia.com/XFree86/Linux-x86_64/470.82.00/NVIDIA-Linux-x86_64-470.82.00.run
Have you tested this driver? I have RTX 3xxx Cards, I need to make sure not miss with rig, its located far away from me.
driver is ok.. can confirm that
A 19.20 (kernel)
N 470.82.00
DRIVERS
[moderator's note: consecutive posts merged]
October 27, 2021, 05:09:23 PM
470.74 is not the latest. this driver only support cuda 11.3
this is the latest available on HiveOS, used : nvidia-driver-update --list and it was latest one in the list
latest driver version is 470.82 , you can update using this command
nvidia-driver-update https://us.download.nvidia.com/XFree86/Linux-x86_64/470.82.00/NVIDIA-Linux-x86_64-470.82.00.run
Have you tested this driver? I have RTX 3xxx Cards, I need to make sure not miss with rig, its located far away from me.
October 27, 2021, 05:00:14 PM
perhaps you need to give execute permissions.
$ chmod a+rwx tbminer
$ chmod a+rwx tbminer
did that command, didnt help.
FYI, I only cp TBminer from tar file to 1.19 directory. shall I copy also miner.conf cacert.pem ?
If they are from the original tbm directory on hiveos than probably yes.
October 27, 2021, 04:59:00 PM
I am not mining to ethermine, I am mining @ 2miners pool. please check screenshot attached
https://i.imgur.com/CbHQS6V.png
https://i.imgur.com/CbHQS6V.png
Upgrade the driver to the latest
https://github.com/sp-hash/TeamBlackMiner/issues/78
I have Latest Drivers installed :
N 470.74
Drivers
The only thing done, is that I manually replaced 1.19 to 1.20 by using commands in bash. may be something went wrong or I miss to do something while replacing 1.19 ?
add this line in miner.config --api-port 64068
Didnt help, still nothing. let me try replace 1.19 Back and check the results, seems issue in 1.20 !!
October 27, 2021, 04:56:21 PM
470.74 is not the latest. this driver only support cuda 11.3
this is the latest available on HiveOS, used : nvidia-driver-update --list and it was latest one in the list
latest driver version is 470.82 , you can update using this command
nvidia-driver-update https://us.download.nvidia.com/XFree86/Linux-x86_64/470.82.00/NVIDIA-Linux-x86_64-470.82.00.run
October 27, 2021, 04:53:22 PM
You might need to configure it. The defaults arent optimal on all pools.
https://github.com/sp-hash/TeamBlackMiner/blob/main/FAQ.md
https://github.com/sp-hash/TeamBlackMiner/blob/main/FAQ.md
October 27, 2021, 04:50:29 PM
This miner reports high numbers but at the pool its much lower than Trex.
October 27, 2021, 04:50:15 PM
I am not mining to ethermine, I am mining @ 2miners pool. please check screenshot attached
https://i.imgur.com/CbHQS6V.png
https://i.imgur.com/CbHQS6V.png
Upgrade the driver to the latest
https://github.com/sp-hash/TeamBlackMiner/issues/78
I have Latest Drivers installed :
N 470.74
Drivers
The only thing done, is that I manually replaced 1.19 to 1.20 by using commands in bash. may be something went wrong or I miss to do something while replacing 1.19 ?
add this line in miner.config --api-port 64068
October 27, 2021, 04:49:20 PM
perhaps you need to give execute permissions.
$ chmod a+rwx tbminer
$ chmod a+rwx tbminer
did that command, didnt help.
FYI, I only cp TBminer from tar file to 1.19 directory. shall I copy also miner.conf cacert.pem ?
October 27, 2021, 04:45:48 PM
perhaps you need to give execute permissions.
$ chmod a+rwx tbminer
$ chmod a+rwx tbminer
Thats a good one.
Maybe also check if .sh files are in linux/unix format as it has happened that files when you open them with vi they have ^M on every line which you need to remove.
October 27, 2021, 04:41:28 PM
perhaps you need to give execute permissions.
$ chmod a+rwx tbminer
$ chmod a+rwx tbminer
Jump to: