.... | Bitcointalksearch.org

Valnurat

full member

Activity: 167

Merit: 100

Quote from: NotFuzzyWarm on August 04, 2017, 10:07:47 AM

A. Miner software questions should go here Mining Software
B. Um, ever tried looking at the 2PAC thread? As in the very 1st post where all your setup questions are answered?
GekkoScience 2Pac BM1384 Stickminer Official Support Thread

Thank you. I will look into it.

NotFuzzyWarm

legendary

Activity: 3822

Merit: 2703

Evil beware: We have waffles!

A. Miner software questions should go here Mining Software
B. Um, ever tried looking at the 2PAC thread? As in the very 1st post where all your setup questions are answered?
GekkoScience 2Pac BM1384 Stickminer Official Support Thread

Valnurat

full member

Activity: 167

Merit: 100

Is Minepeon still alive?

fireclown

newbie

Activity: 4

Merit: 0

guys:

I have a few really, REALLY basic problems. If this is the wrong place for them, please point me in the right direction.

I'm putting together a bitcoin rig for fun out of stuff I have around the house (mostly).

1 RP 3
1 ANKER 7 port powered USB hub
1 gekkoscience 2pac exploder

I have the ANKER plugged into a wall outlet and the Gekko 2pac plugged into that. The indicator light is glowing a cheery green.
I downoaded minepeon and sent it over to my microSD. I checked the directory, and it is shown below. The PI is getting power, and the indicator LED is red. I have a cable running from my PI to my (netgear) router.

I'm at the point where I have to find the IP address of the pi so that I can direct it to my pool (I'm using slushpool). My first problem is that when I log into the router, I can't see the PI. So I'm kind of at a standstill.

I had kind of assumed that to run the mining software, I would install it onto my PI from scratch, without an OS, that is was some kind of bianary magic that would run itself when it rfound itself in contact with the magical commands from the 2pac. Do I need to install rasbian?

Thanks in advance
http://i63.tinypic.com/k12n2x.jpg

Lagniappe

newbie

Activity: 42

Merit: 0

Quote from: wolverine5pl on January 30, 2016, 09:01:50 PM

Will it work on raspberry pi a+?

I don't see why not. All it's doing is networking with your miners, not cpu mining itself.

By the way, first post, just wanted to say, much respect to all you Bitcoin miners. I missed the Bitcoin train and got left in Nov2013, I jumped off with what I thought was enough and, it wasn't. Here to learn, and here to generate heat, and make the lady angry, that Ubuntu is getting the attention.

All the best,
Norman

justagentleman

newbie

Activity: 2

Merit: 0

I already tried 3 different micro sd card, can you tell me a model that is known for working with minepeon ? thank you

wolverine5pl

sr. member

Activity: 437

Merit: 250

Will it work on raspberry pi a+?

kraideasa

newbie

Activity: 1

Merit: 0

Hello follow all the tutorial but when placing the card in raspberry pi 2 it does not happen anything. as if he did not have anything on the card and does not appear in the network also. Huh

Kx2000

newbie

Activity: 13

Merit: 0

Hi

Any ghuide to upgrade minepeon both miners ?

Thanks

sterlingcapital

full member

Activity: 177

Merit: 100

Can anyone help me with an issue of the commands in miner.conf and miner.user.conf keep getting reset every time i change the pool in the GUI from the browser?

I am trying to add

--api-allow W:127.0.0.1,W:192.168.1.155

for cgremote
everything works fine after reboot until I decide to change the pool from the GUI then everything gets reset to default again.

kevin1234a

legendary

Activity: 1162

Merit: 1000

Decentralizing Jesus on the Blockchain

[/quote]

There is often a lot of discussion about the best way to patch miner software and MinePeon in general on the MinePeon technical forums;-

http://minepeon.com/forums/viewforum.php?f=4&sid=439cccd31de7c22641068da77eaf6ace

Most recently the patching of cgminer for Techobit HEX2a was discussed but it mostly applies to what your want to do. If not, start a thread.

Neil
[/quote]

is it possible to use minepeon for dual mining wiith gridseed 5chips ?

ManeBjorn

legendary

Activity: 1288

Merit: 1004

I do have one problem.
Every time I add a password through the web console it locks me out unless it is a simple 4 letter PW.
I can still access it through putty and even change the console password there but still cannot get back into the web console.
I do not want to leave it open and help would be great.

ManeBjorn

legendary

Activity: 1288

Merit: 1004

Great guide.
I just got started with RPI's in the last couple days.
MinePeon was easy to setup and use.
The MobileMiner plugin works great with my MultiMiner setups.

I have one of these LCD's is there a way to for it to work with MP?
http://www.ebay.com/itm/121004607232?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649

Patron92

full member

Activity: 234

Merit: 100

Thanks a lot for this guide! As I am newbie it was difficult for me to set up everything appropriately !

Xello

newbie

Activity: 15

Merit: 0

The data is really nice! and the instruction is pretty easy but needed time to do everything correctly

stevepd

newbie

Activity: 7

Merit: 0

hello there , need some help I installed minepeon from there website 0.2.4.6 its on the sdcard works fine I updated all software on it ex.. f,g,h ect in the device menu ,

I put in my mining pool info from we mine ltc its default setting is bfminer ... restarted it and im stuck on the console menu

I do not see my pool info OR devices when I log into raspberry via computer

devices says NO Devices running and nothing under pools

is there anything else I have to install on sd card ? or any commands I have to give the raspberry ?

thanks for your time , can you give me step by step info

berliston

jr. member

Activity: 52

Merit: 21

Did you try to SSH into the Raspberry PI running Minepeon?

cannachris

sr. member

Activity: 406

Merit: 250

cats love crypto | 911 truth @checktheevidence.com

hey i formatted my sd card with raspian a while ago with the same tools, now i want to write minepeon to it but my win8 pc says the drive is empty, and no activity lights flash...

did i break the sd card? help!

doktorwhy

newbie

Activity: 10

Merit: 0

Hi just started mining with brand new red Bi-Fury 5ghs with raspberry pi - minepeon
change cgminer to bfgminer just plug it in & change its pool address using minepeon ssh screen
([p]ool management) url: > username: > and off it goes 5.12 ghs $1.40 in 3 days. Make sure you use a good fan or 2 works fine at 40 °c . 1 today 5 more on there way thanks to cryptostore.io great price.

Dave Cool

MineForeman.com

legendary

Activity: 896

Merit: 1000

Quote from: Lucko on March 04, 2014, 06:25:19 PM

I guess this is not the right place but if i would like to integrate this driver in bfgminer.
http://www75.zippyshare.com/v/49421870/file.html
How do I do that?

There is often a lot of discussion about the best way to patch miner software and MinePeon in general on the MinePeon technical forums;-

http://minepeon.com/forums/viewforum.php?f=4&sid=439cccd31de7c22641068da77eaf6ace

Most recently the patching of cgminer for Techobit HEX2a was discussed but it mostly applies to what your want to do. If not, start a thread.

Neil

Topic: .... (Read 77298 times)