N factor just kicked in. I started getting HW errors.
Yep, HW's flying all over the place
Alrighty, then, lets get this party started :-)
Adjusted my miners ahead of time - mining perfectly fine without HW errors
Topic: [ANN] [ASIC-RESISTANT] UltraCoin (UTC) - Ultrafast 6 second transactions!! - page 282. (Read 946650 times)
April 05, 2014, 09:54:02 PM
Yep, HW's flying all over the place
Alrighty, then, lets get this party started :-)
Adjusted my miners ahead of time - mining perfectly fine without HW errors
April 05, 2014, 09:52:54 PM
simply increasing tc this time isn't working for my 7950s
Thirtybird could tell you better than me, especially if you are using his miner, but try upping your lookup gap 1 and your TC the same percent% e.g. -- lookup gap 2 --> 3, raise TC 33% and see what happens.
April 05, 2014, 09:47:52 PM
im getting close.. HW is 2 in 2 minutes
April 05, 2014, 09:45:34 PM
simply increasing tc this time isn't working for my 7950s
April 05, 2014, 09:45:27 PM
no one is sharing since they want to mine all those UTCs
Well, I was getting 135Kh/s before. So far I managed only 30Kh/s withouth HW errors. =(
I assume that's not optimal. So until I can get higher, I won't be posting any bad configs.
I'm in the same boat, only I couldn't use the suggested settings last time either. I had to run a lookup-gap of 3 with my 3 290x/ 1 290 rig. Now I can't seem to get all 4 cards to run again, even with a lookup-gap of 4 as I can't raise the thread concurrency high enough on each card to get rid of the HW errors on all cards before I get the Error 4: cannot enqueue...... The cards I can get it running on are running at about 40% of my old hash rate. The most I can get running at once are 3 of the 4 cards. I can get those running at 55% of old rate with no HW errors.
April 05, 2014, 09:43:02 PM
no one is sharing since they want to mine all those UTCs
Well, I was getting 135Kh/s before. So far I managed only 35Kh/s withouth HW errors. =(
I assume that's not optimal. So until I can get higher, I won't be posting any bad configs.
April 05, 2014, 09:38:59 PM
no one is sharing since they want to mine all those UTCs
April 05, 2014, 09:35:10 PM
This would be so much easier without 4 cards.
April 05, 2014, 09:30:52 PM
With 280x, roughly what hash rate is considered good now? About 60-70Kh/s?
April 05, 2014, 09:28:46 PM
Does anyone have a new settings for 280x for the current n factor?
April 05, 2014, 09:27:56 PM
N factor just kicked in. I started getting HW errors.
Yep, HW's flying all over the place
Alrighty, then, lets get this party started :-)
Adjusted my miners ahead of time - mining perfectly fine without HW errors
You don't count. We normal people still have work to do
lol, yeah working my bumm of right here
April 05, 2014, 09:24:41 PM
N factor just kicked in. I started getting HW errors.
Yep, HW's flying all over the place
Alrighty, then, lets get this party started :-)
Adjusted my miners ahead of time - mining perfectly fine without HW errors
You don't count. We normal people still have work to do
April 05, 2014, 09:21:46 PM
N factor just kicked in. I started getting HW errors.
Yep, HW's flying all over the place
Alrighty, then, lets get this party started :-)
Adjusted my miners ahead of time - mining perfectly fine without HW errors
April 05, 2014, 09:19:45 PM
N factor just kicked in. I started getting HW errors.
Yep, HW's flying all over the place
Alrighty, then, lets get this party started :-)
April 05, 2014, 09:16:01 PM
N factor just kicked in. I started getting HW errors.
April 05, 2014, 09:07:57 PM
N factor change 13 minutes.
Quote from bumface on page 579.Quote
expect an N factor delay withing some time (extending the gpu era)
That's for the next N-factor. Not for today's one. (5 minutes now)
I'll come back and play for a little bit with the ultracoin miner and see what I get when it changes.
edit: are you sure it hasn't already changed. I got all HW errors as soon as I started with my old miner settings that worked last week. ]
edit: and my rate is halved.
April 05, 2014, 09:06:54 PM
N factor change 13 minutes.
Quote from bumface on page 579.Quote
expect an N factor delay withing some time (extending the gpu era)
That's for the next N-factor. Not for today's one. (5 minutes now)
April 05, 2014, 09:04:55 PM
N factor change 13 minutes.
Quote from bumface on page 579.Quote
expect an N factor delay withing some time (extending the gpu era)
April 05, 2014, 09:02:47 PM
N factor change 13 minutes.
Yes, I have the sound of Jaws running through my head, just waiting. Da dun, da dun, dun dun dun dun! April 05, 2014, 09:01:51 PM
difficulty at 2! n-factor change scaring people off??? Or nitro pool domination KILLING the other pools off. We should just call it UltraNitroCoin.....zooooom!
So how does this pool thing work anyway. Nitro has 1200+ miners, I doubt the miners could collude together to co-ordinate a 51% attack so is it the pool operater that could coordinate an attack. Just curios where the actual threat is.
So how does this pool thing work anyway. Nitro has 1200+ miners, I doubt the miners could collude together to co-ordinate a 51% attack so is it the pool operater that could coordinate an attack. Just curios where the actual threat is.
I'm not mining, but didn't the N-factor just kick in, diff would half if it did.
It hasn't kicked in yet. It's still another 10mins away.
04 / 06 / 14 @ 02:10:08am UTC
Having a pool with >50% isn't that dangerous. But it does cause problems for other pools.
Ultracoin isn't the only with this problem however.
Other non-scrypt coins usually end up with 1 big pool and less than a handful of small pools also. (due to lack of multi-pools)
Once there are adaptive-N multi-pools, we won't have this monopoly-pool issue. (although it doesn't really benefit Ultracoin)
Jump to: