Author

Topic: [ANN] Spondoolies-Tech - carrier grade, data center ready mining rigs - page 333. (Read 1260365 times)

sr. member
Activity: 404
Merit: 362
in bitcoin we trust
Beautiful well built hardware is great but it does no good if btc price keeps falling and difficulty keeps going up. How good is a miner if BTC goes sub $100 and it costs more to power the thing than it earns.  Cry

Miners need to shut down but as long as people speculate that BTC will rise in the future they will continue to mine at a loss today.

I am not sure they will continue to mine.  It is more profitable to switch off older equipment and buy bitcoin than spend electricity at loss making J/BTC cost basis.

Its normal at any given time that people will be switching off previous gen equipment as newer more electrically efficient equipment pushes old hardware below electrical breakeven with sunk cost economics (ie even losing money based on electrical cost, ignoring purchase cost).

Same thing happened to CPUs, GPUs, FPGAs... now its the turn of old gen ASICs.

Once they adapt difficulty will flatten or even fall, sell pressure will relieve and price will rise.  Flatter difficulty will help also because it extends equipment life-time which makes planning easier.

Thats what I think anyway.

Adam
legendary
Activity: 915
Merit: 1005
The latest that I am on is 2.4.20 . Nothing else comes back for SP when I try to upgrade
My bad, you are right the version is 2.4.20

Cool Talked too early for me. I have no more errors but it is still not stable. Will have to follow up with SP-Teach tomorrow
sr. member
Activity: 314
Merit: 250
The latest that I am on is 2.4.20 . Nothing else comes back for SP when I try to upgrade
My bad, you are right the version is 2.4.20
legendary
Activity: 915
Merit: 1005
SP-Tech support is world class not only in the Bitcoin industry but technical support in general

  • Upgraded to the latest firmware
  • Made the change in their technical blog as advised echo 1 > /etc/mg_dc2dc_temp_ignore)
  • Now hashing away
  • Offered to ssh into the machine

You cannot ask for better server . Hopefully they don't tease us with all these nice customer services then turn into BFL and KNC

I agree they have been very helpful ...
meanwhile got the Loop9 problem again - Just upgraded to 2.4.40 and noticed the fans were set to 70% and some of the ASICS were at 115c .. configured the Fans back to 80%, restarted miner gate and had the issue you earlier described. I just reboot the machine and is hashing away.

The latest that I am on is 2.4.20 . Nothing else comes back for SP when I try to upgrade
sr. member
Activity: 314
Merit: 250
SP-Tech support is world class not only in the Bitcoin industry but technical support in general

  • Upgraded to the latest firmware
  • Made the change in their technical blog as advised echo 1 > /etc/mg_dc2dc_temp_ignore)
  • Now hashing away
  • Offered to ssh into the machine

You cannot ask for better server . Hopefully they don't tease us with all these nice customer services then turn into BFL and KNC

I agree they have been very helpful ...
meanwhile got the Loop9 problem again - Just upgraded to 2.4.40 and noticed the fans were set to 70% and some of the ASICS were at 115c .. configured the Fans back to 80%, restarted miner gate and had the issue you earlier described. I just reboot the machine and is hashing away.
legendary
Activity: 915
Merit: 1005
SP-Tech support is world class not only in the Bitcoin industry but technical support in general

  • Upgraded to the latest firmware
  • Made the change in their technical blog as advised echo 1 > /etc/mg_dc2dc_temp_ignore)
  • Now hashing away
  • Offered to ssh into the machine

You cannot ask for better server . Hopefully they don't tease us with all these nice customer services then turn into BFL and KNC
legendary
Activity: 915
Merit: 1005
Recieved a miner on Friday that was preordered. However it has not run at above 2 TH. I thought it was just doing its calibration thing but upon further investigation the miner appears to not be functional.
Any advice on getting this fixed ?
Did you already emailed SP support?  they are usually pretty fast!

What is their support email ? Is it  [email protected] . Nothing on the contact us page http://www.spondoolies-tech.com/pages/contact-us

It's support@

It seems that you have a dead PSU. Tried swapping it out and pressing it back in?

The Murata PSUs do not manage to recover from OC. Please update to latest version (2.4.20) and do full 30 second long power cycle.

Thanks. Waiting to have the machines power cycled
legendary
Activity: 1582
Merit: 1019
011110000110110101110010
High resolution SP20 pics: http://imgur.com/a/ltKAR
This is a beautiful and proper built miner!

Indeed, it's beautiful well built professional grade hardware, if only the price...

Beautiful well built hardware is great but it does no good if btc price keeps falling and difficulty keeps going up. How good is a miner if BTC goes sub $100 and it costs more to power the thing than it earns.  Cry

Miners need to shut down but as long as people speculate that BTC will rise in the future they will continue to mine at a loss today.
sr. member
Activity: 407
Merit: 255
High resolution SP20 pics: http://imgur.com/a/ltKAR
This is a beautiful and proper built miner!

Indeed, it's beautiful well built professional grade hardware, if only the price...

Beautiful well built hardware is great but it does no good if btc price keeps falling and difficulty keeps going up. How good is a miner if BTC goes sub $100 and it costs more to power the thing than it earns.  Cry
newbie
Activity: 43
Merit: 0
Recieved a miner on Friday that was preordered. However it has not run at above 2 TH. I thought it was just doing its calibration thing but upon further investigation the miner appears to not be functional.
Any advice on getting this fixed ?
Did you already emailed SP support?  they are usually pretty fast!

What is their support email ? Is it  [email protected] . Nothing on the contact us page http://www.spondoolies-tech.com/pages/contact-us

It's support@

It seems that you have a dead PSU. Tried swapping it out and pressing it back in?

The Murata PSUs do not manage to recover from OC. Please update to latest version (2.4.20) and do full 30 second long power cycle.

Also check the fuses in your plugs. 

When I first got mine I used cables which had been used on Antminer S3 and CoinTerra Miners.  They only had 5A fuses and blew within the first 2hours.

As stated above, update to latest firmware then power cycle the miner.  You may also want to confirm the max PSU is set to 1300w or lower under Settings > MAX PSU Top and MAX PSU Bottom.  This will not effect the performance of the miner but will facilitate the miner working when it hits over current.

Hope that helps.
hero member
Activity: 560
Merit: 500
Recieved a miner on Friday that was preordered. However it has not run at above 2 TH. I thought it was just doing its calibration thing but upon further investigation the miner appears to not be functional.
Any advice on getting this fixed ?
Did you already emailed SP support?  they are usually pretty fast!

What is their support email ? Is it  [email protected] . Nothing on the contact us page http://www.spondoolies-tech.com/pages/contact-us

It's support@

It seems that you have a dead PSU. Tried swapping it out and pressing it back in?

The Murata PSUs do not manage to recover from OC. Please update to latest version (2.4.20) and do full 30 second long power cycle.
newbie
Activity: 43
Merit: 0
Hi Guys,

Is it possible in a firmware update to produce the ability to monitor the miners via SNMP? 

This way I could fire up a Cacti instance and graph data in single location for all the miners.

Thanks.
legendary
Activity: 1904
Merit: 1007
Recieved a miner on Friday that was preordered. However it has not run at above 2 TH. I thought it was just doing its calibration thing but upon further investigation the miner appears to not be functional.
Any advice on getting this fixed ?
Did you already emailed SP support?  they are usually pretty fast!

What is their support email ? Is it  [email protected] . Nothing on the contact us page http://www.spondoolies-tech.com/pages/contact-us

It's support@

It seems that you have a dead PSU. Tried swapping it out and pressing it back in?
legendary
Activity: 915
Merit: 1005
Recieved a miner on Friday that was preordered. However it has not run at above 2 TH. I thought it was just doing its calibration thing but upon further investigation the miner appears to not be functional.
Any advice on getting this fixed ?
Did you already emailed SP support?  they are usually pretty fast!

What is their support email ? Is it  [email protected] . Nothing on the contact us page http://www.spondoolies-tech.com/pages/contact-us

*sent an email to  [email protected]
sr. member
Activity: 314
Merit: 250
Recieved a miner on Friday that was preordered. However it has not run at above 2 TH. I thought it was just doing its calibration thing but upon further investigation the miner appears to not be functional.
Any advice on getting this fixed ?
Did you already emailed SP support?  they are usually pretty fast!
legendary
Activity: 915
Merit: 1005
Received a miner on Friday that was preordered. However it has not run at above 2 TH. I thought it was just doing its calibration thing but upon further investigation the miner appears to not be functional.

Any advice on getting this fixed ?

Code:
3: DC2DC/1/:[vlt1:599 vlt2:600(DCl:794 Tl:600 Ul:749) 24W  40A 251c] ASIC:[ 85c* 350hz(BL: 550)    7 (E:193) F:0]
 4: DC2DC/1/:[vlt1:597 vlt2:600(DCl:794 Tl:600 Ul:749) 24W  41A 254c] ASIC:[ 85c* 350hz(BL: 605)    5 (E:193) F:0]
 5: DC2DC/1/:[vlt1:601 vlt2:600(DCl:794 Tl:600 Ul:749) 24W  41A 254c] ASIC:[ 85c* 350hz(BL: 600)    9 (E:193) F:0]
LOOP[2] ON
 6: DC2DC/1/:[vlt1:599 vlt2:600(DCl:794 Tl:600 Ul:749) 25W  41A 253c] ASIC:[ 85c* 350hz(BL: 590)    5 (E:193) F:0]
 7: DC2DC/1/:[vlt1:597 vlt2:600(DCl:794 Tl:600 Ul:749) 25W  41A 255c] ASIC:[ 85c* 350hz(BL: 500)    6 (E:193) F:0]
 8: DC2DC/1/:[vlt1:601 vlt2:600(DCl:794 Tl:600 Ul:749) 25W  41A 252c] ASIC:[ 85c* 350hz(BL:1045)    4 (E:171) F:0]
LOOP[3] ON
 9: DC2DC/1/:[vlt1:601 vlt2:600(DCl:794 Tl:600 Ul:749) 25W  41A 254c] ASIC:[ 85c* 350hz(BL: 545)    4 (E:193) F:0]
10: DC2DC/1/:[vlt1:599 vlt2:600(DCl:794 Tl:600 Ul:749) 25W  41A 255c] ASIC:[ 85c* 350hz(BL: 575)    8 (E:193) F:0]
11: DC2DC/1/:[vlt1:605 vlt2:602(DCl:794 Tl:602 Ul:749) 25W  42A 254c] ASIC:[ 85c* 350hz(BL: 625)    5 (E:191) F:0]
LOOP[4] ON
12: DC2DC/1/:[vlt1:666 vlt2:672(DCl:794 Tl:794 Ul:749) 53W  79A   9c] ASIC:[ 85c  615hz(BL: 615)   10 (E:193) F:0]
13: DC2DC/1/:[vlt1:666 vlt2:672(DCl:794 Tl:794 Ul:749) 54W  80A  10c] ASIC:[ 85c  630hz(BL: 630)   15 (E:193) F:0]
14: DC2DC/1/:[vlt1:599 vlt2:600(DCl:794 Tl:600 Ul:749) 25W  42A 254c] ASIC:[ 85c* 350hz(BL: 595)    5 (E:193) F:0]
LOOP[5] OFF (test serial failed)
15: disabled (i2c BAD, btw!)
16: disabled (i2c BAD, btw!)
17: disabled (i2c BAD, btw!)
LOOP[6] OFF (test serial failed)
18: disabled (i2c BAD, btw!)
19: disabled (i2c BAD, btw!)
20: disabled (i2c BAD, btw!)
LOOP[7] OFF (test serial failed)
21: disabled (i2c BAD, btw!)
22: disabled (i2c BAD, btw!)
23: disabled (i2c BAD, btw!)
LOOP[8] OFF (test serial failed)
24: disabled (i2c BAD, btw!)
25: disabled (i2c BAD, btw!)
26: disabled (i2c BAD, btw!)
LOOP[9] OFF (test serial failed)
27: disabled (i2c BAD, btw!)
28: disabled (i2c BAD, btw!)
29: disabled (i2c BAD, btw!)

[H:HW:1118Gh,W:432,L:0,A:15,MMtmp:0 TMP:(14)=>=>=>(23,0)]
Pushed 27 jobs , in HW queue 4 jobs (sw:3, hw:3)!
min:30 wins:103[this/last min:98/5] bist-fail:36, hw-err:
sr. member
Activity: 314
Merit: 250
update: Upgrade to 2.3.46 fixed the issue.

Happy New Year!

So does a couple of minergate resets, temporary Smiley Loop 9 looks the toughest to please ..

When the unit is starting to mine, minergate modifies the asic frequencies to bump the hashrate up .. it starts from loop 1 and ends with loop 9 .. sometimes I feel like loop 9 is not started because everything else is running above parameters. With loop 9 off, the other loops try to compensate the missing hashrate and they're overclocked.

http://powerprice.info/SPT/graphic.php << see the "loop 9 issue" when the bottom board exhaust temperature is 56 deg C or so. With 2.3.46 fixing the issue means this problem with loop 9 does not appear at all?
I never had this Loop 9 issue until yesterday .. what I noticed was the hashrate decreasing slowly to the ~4.2~ and I needed to manual restarted minergate to bump it up again to the ~4.5 range.
Now the 2.4.15 FW release notes states it fixes this problem. Also Zvi told me to upgrade to the last version of the FW ... so I will upgrade to 2.4.18 as soon as  I have remote hands in case a power off is needed.

On the other hand I have a SP30 running with FW 2.3.43 running at ~4950 since day 1 like a Swiss watch!

hero member
Activity: 572
Merit: 500
update: Upgrade to 2.3.46 fixed the issue.

Happy New Year!

So does a couple of minergate resets, temporary Smiley Loop 9 looks the toughest to please ..

When the unit is starting to mine, minergate modifies the asic frequencies to bump the hashrate up .. it starts from loop 1 and ends with loop 9 .. sometimes I feel like loop 9 is not started because everything else is running above parameters. With loop 9 off, the other loops try to compensate the missing hashrate and they're overclocked.

http://powerprice.info/SPT/graphic.php << see the "loop 9 issue" when the bottom board exhaust temperature is 56 deg C or so. With 2.3.46 fixing the issue means this problem with loop 9 does not appear at all?
legendary
Activity: 1904
Merit: 1007
update: Upgrade to 2.3.46 fixed the issue.

Happy New Year!
sr. member
Activity: 314
Merit: 250
Hello, oOne of my miners performance decreased a bit (~10%) .. I checked the ASIC Events and it looks like there is an issue with the bottom board. Loop9 OFF.

I already rebooted the miner and restarted the miner gate couple of times ... anyone saw this before?

----BOTTOM BOARD------
PSU-BOT[EMERSON1200]: 1392->1280w[1280 1264 1260] (lim=1335) 0c cooling:0/0x2000

LOOP[9] OFF (no data on loop)
27: disabled (i2c good)
28: disabled (i2c good)
29: disabled (i2c good)

[H:HW:3868Gh[2114+1754],W:1810,L:0,A:27,MMtmp:0 TMP:(20)=>=>=>(63,44)]



thx

I got the same on one miner. What have I done is set both PSUs to 1340W (on 220V+) so they can re-optimize. You should get ~4200 from that miner.

Ok, thank you Roadstress -  will try. The miner is currently at 4200 Ghs without changing settings and with the Loop9 OFF ..... Before that do you or anyone knows where to find the SP firmware versions for manual upgrade?

update: Upgrade to 2.3.46 fixed the issue.
Jump to: