Hi all.
I will not be availible for the next week.
Please write to support@ and Remo will help you.
Have a good week everyone.
Topic: [ANN] Spondoolies-Tech - carrier grade, data center ready mining rigs - page 598. (Read 1260354 times)
June 02, 2014, 05:58:48 AM
June 02, 2014, 05:57:23 AM
Looks like one of my chips doesnt work? Ive rebooted the miner, have the latest firmware, and have tried tweaking the voltage settings but with no avail.
perhaps switching over to 208V will kick some sense into the machine - otherwise it is running great right now at 1.3TH with the fans tuned down a little
I have a few questions though:
1) what is the HW error rate? is it the 'errors'/'accepted shares' on the main page? - because the initial power up makes a huge error rate seemingly. Pool stats seem pretty good though so wasn't sure if its like the antminers where a few other variables need to be accounted for in the error rate %
-- Errors are OK if you are getting close hash rate in pool (not more then 3% differentce)
2) how accurate is the wattage reading on the asic stats page? Assuming its correct then these units really are outstanding at 1.34TH/1100W
-- It's kind-off accurate, not 100%. The number you see is not at the wall, you should add ~6-7% to it.
edit: rebooted the miner to see if that remedies the odd chip, and now am getting weird results. The miner will spin up and sound like it is mining properly for about 45seconds, then drop to idle for 40 seconds, then spin up all the fans to mining speeds again. pool shows alive and a few various chips read as 7fdf or 7fbf or 7ffd. Every spin up/down seems like it might be reducing thre number of weird chip codes
-- It may be that your starting voltage is too low.
edit 2: something is bugging my miner. I disabled a file upload and it seems like that may have corrected the issue with hashing starting and stopping (I guess my upload speeds were too limited??). most chips but one (7fdf) are reading 7fff and miner is stabilising slowly. time for bed - i guess ill have to upload files another way?
-- 7FFF is the engine bitmask. In some ASICs 1 engine not working, it will show different mask. Sometimes 1 engine does not work well in low voltage. Don't worry unless you have many - other engines compensate.
^can someone confirm the bandwidth needs (especiall the upload speeds) of the miner? I was uploading files at ~66kBps which i know is slow but i thought is more than sufficient for mining
--- The miner hardly takes any bandwith, less then 1 Kbps if I remember correctly. But it can be sensitive to latency. It's standard cgminer.
Code:
43: 77c 825hz( 0/ 0) 0 1
-- I released version 1.3.52 just - see if it discoveres the runaway ASIC.perhaps switching over to 208V will kick some sense into the machine - otherwise it is running great right now at 1.3TH with the fans tuned down a little
I have a few questions though:
1) what is the HW error rate? is it the 'errors'/'accepted shares' on the main page? - because the initial power up makes a huge error rate seemingly. Pool stats seem pretty good though so wasn't sure if its like the antminers where a few other variables need to be accounted for in the error rate %
-- Errors are OK if you are getting close hash rate in pool (not more then 3% differentce)
2) how accurate is the wattage reading on the asic stats page? Assuming its correct then these units really are outstanding at 1.34TH/1100W
-- It's kind-off accurate, not 100%. The number you see is not at the wall, you should add ~6-7% to it.
edit: rebooted the miner to see if that remedies the odd chip, and now am getting weird results. The miner will spin up and sound like it is mining properly for about 45seconds, then drop to idle for 40 seconds, then spin up all the fans to mining speeds again. pool shows alive and a few various chips read as 7fdf or 7fbf or 7ffd. Every spin up/down seems like it might be reducing thre number of weird chip codes
-- It may be that your starting voltage is too low.
edit 2: something is bugging my miner. I disabled a file upload and it seems like that may have corrected the issue with hashing starting and stopping (I guess my upload speeds were too limited??). most chips but one (7fdf) are reading 7fff and miner is stabilising slowly. time for bed - i guess ill have to upload files another way?
-- 7FFF is the engine bitmask. In some ASICs 1 engine not working, it will show different mask. Sometimes 1 engine does not work well in low voltage. Don't worry unless you have many - other engines compensate.
^can someone confirm the bandwidth needs (especiall the upload speeds) of the miner? I was uploading files at ~66kBps which i know is slow but i thought is more than sufficient for mining
--- The miner hardly takes any bandwith, less then 1 Kbps if I remember correctly. But it can be sensitive to latency. It's standard cgminer.
See inline )
June 02, 2014, 05:33:05 AM
Whats not clear really in the checkout process is if you have to pay for shipping if you are hosting there. So in that instance I would email sales@ and they will probably send you a discount code for the shipping cost to add to the cart before checkout, and just make sure to put all the hosting info in the notes.
If you choose the hosting package, you just select the 'free shipping' option then it doesn't charge you.
Shipping rates are the same all over the world, roughly 190$ per device, shipping via DHL/UPS express.
June 02, 2014, 05:25:50 AM
Whats not clear really in the checkout process is if you have to pay for shipping if you are hosting there. So in that instance I would email sales@ and they will probably send you a discount code for the shipping cost to add to the cart before checkout, and just make sure to put all the hosting info in the notes.
If you choose the hosting package, you just select the 'free shipping' option then it doesn't charge you.
June 02, 2014, 03:45:15 AM
Hi there.
If I purchased an SP10 + 3 month hosting - what is the lead time in getting that installed and up and running for me?
Also I couldn't find a shipping estimator on the website - if I just wanted it to be shipped to the UK what would be the approximate cost and lead time for this?
Cheers
Dave
If I purchased an SP10 + 3 month hosting - what is the lead time in getting that installed and up and running for me?
Also I couldn't find a shipping estimator on the website - if I just wanted it to be shipped to the UK what would be the approximate cost and lead time for this?
Cheers
Dave
Hosting, I think it took under 48 hours to be up and hashing.
$193 to ship to the UK, you have to go through the checkout process to get the shipping price, it gives it to you before you complete.
Whats not clear really in the checkout process is if you have to pay for shipping if you are hosting there. So in that instance I would email sales@ and they will probably send you a discount code for the shipping cost to add to the cart before checkout, and just make sure to put all the hosting info in the notes.
June 02, 2014, 03:41:31 AM
Hi there.
If I purchased an SP10 + 3 month hosting - what is the lead time in getting that installed and up and running for me?
Also I couldn't find a shipping estimator on the website - if I just wanted it to be shipped to the UK what would be the approximate cost and lead time for this?
Cheers
Dave
If I purchased an SP10 + 3 month hosting - what is the lead time in getting that installed and up and running for me?
Also I couldn't find a shipping estimator on the website - if I just wanted it to be shipped to the UK what would be the approximate cost and lead time for this?
Cheers
Dave
June 01, 2014, 11:19:07 PM
I have a late May unit, and it's only averaging ~1300 GH/s at the pool (BtcGuild) using the "turbo fans, highest rate" setting. Is there anything I can do to increase performance?
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
I have the same thing on 2 units.
whats your advanced voltage settings? if your max voltage is set at default then that may be the limitation.
It will also run slower and less efficient on a 120V circuit compared to a standard 240V one, as the PSU will not be able to deliver the same current.
June 01, 2014, 10:37:52 PM
I have a late May unit, and it's only averaging ~1300 GH/s at the pool (BtcGuild) using the "turbo fans, highest rate" setting. Is there anything I can do to increase performance?
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
I have the same thing on 2 units.
whats your advanced voltage settings? if your max voltage is set at default then that may be the limitation.
June 01, 2014, 10:36:51 PM
Looks like one of my chips doesnt work? Ive rebooted the miner, have the latest firmware, and have tried tweaking the voltage settings but with no avail.
perhaps switching over to 208V will kick some sense into the machine - otherwise it is running great right now at 1.3TH with the fans tuned down a little
I have a few questions though:
1) what is the HW error rate? is it the 'errors'/'accepted shares' on the main page? - because the initial power up makes a huge error rate seemingly. Pool stats seem pretty good though so wasn't sure if its like the antminers where a few other variables need to be accounted for in the error rate %
2) how accurate is the wattage reading on the asic stats page? Assuming its correct then these units really are outstanding at 1.34TH/1100W
edit: rebooted the miner to see if that remedies the odd chip, and now am getting weird results. The miner will spin up and sound like it is mining properly for about 45seconds, then drop to idle for 40 seconds, then spin up all the fans to mining speeds again. pool shows alive and a few various chips read as 7fdf or 7fbf or 7ffd. Every spin up/down seems like it might be reducing thre number of weird chip codes
edit 2: something is bugging my miner. I disabled a file upload and it seems like that may have corrected the issue with hashing starting and stopping (I guess my upload speeds were too limited??). most chips but one (7fdf) are reading 7fff and miner is stabilising slowly. time for bed - i guess ill have to upload files another way?
^can someone confirm the bandwidth needs (especiall the upload speeds) of the miner? I was uploading files at ~66kBps which i know is slow but i thought is more than sufficient for mining
Code:
43: 77c 825hz( 0/ 0) 0 1
I have a few questions though:
1) what is the HW error rate? is it the 'errors'/'accepted shares' on the main page? - because the initial power up makes a huge error rate seemingly. Pool stats seem pretty good though so wasn't sure if its like the antminers where a few other variables need to be accounted for in the error rate %
2) how accurate is the wattage reading on the asic stats page? Assuming its correct then these units really are outstanding at 1.34TH/1100W
edit: rebooted the miner to see if that remedies the odd chip, and now am getting weird results. The miner will spin up and sound like it is mining properly for about 45seconds, then drop to idle for 40 seconds, then spin up all the fans to mining speeds again. pool shows alive and a few various chips read as 7fdf or 7fbf or 7ffd. Every spin up/down seems like it might be reducing thre number of weird chip codes
edit 2: something is bugging my miner. I disabled a file upload and it seems like that may have corrected the issue with hashing starting and stopping (I guess my upload speeds were too limited??). most chips but one (7fdf) are reading 7fff and miner is stabilising slowly. time for bed - i guess ill have to upload files another way?
^can someone confirm the bandwidth needs (especiall the upload speeds) of the miner? I was uploading files at ~66kBps which i know is slow but i thought is more than sufficient for mining
June 01, 2014, 10:32:46 PM
I have a late May unit, and it's only averaging ~1300 GH/s at the pool (BtcGuild) using the "turbo fans, highest rate" setting. Is there anything I can do to increase performance?
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
I have the same thing on 2 units.
Was hoping to be on the other side of the +/ -
Will the June batch be a different run of chips?
June 01, 2014, 03:32:08 PM
Worth every BTC, 2 x Sp10 running solid for weeks @ 1.43-1.45, hoping for some SP30 cancellations September is too far away 
June 01, 2014, 03:31:17 PM
Hosting for SP10 was added back
Thanks! Typical that BTC has a 10% selloff as I about to pull the trigger. Need to wait until we recover.
Pull faster (or don't attempt to draw, so it will go higher
)Haha, I'm sure we will be back in the 680-700 range by tomorrow. Haven't bought new mining equipment in a while so excited to be increasing my hashrate soon.
you picked the right h/w manufacturer.
June 01, 2014, 03:20:58 PM
Hosting for SP10 was added back
Thanks! Typical that BTC has a 10% selloff as I about to pull the trigger. Need to wait until we recover.
Pull faster (or don't attempt to draw, so it will go higher
)Haha, I'm sure we will be back in the 680-700 range by tomorrow. Haven't bought new mining equipment in a while so excited to be increasing my hashrate soon.
June 01, 2014, 03:18:09 PM
Mail from Spondoolies-Tech Orderd my SP10 friday evening!
Dear Robin,
After a successful burn-in test, we are happy to announce that your unit was shipped and is now on its way to you.
The unit was shipped with DHL. Please see attached shipping documents.
A lot of work was put into designing, building, and shipping that unit. We believe you will enjoy it very much.
If you have any questions feel free to contact us at [email protected].
Best Regards,
Katya Penkar
Sales Coordinator
Spondoolies-Tech LTD.
Tel.: +972(8)8606636
Fax : +972 (8)8643050
Mobile: +972(54)4882443
That is something else then Black Arrow...djeees
Dear Robin,
After a successful burn-in test, we are happy to announce that your unit was shipped and is now on its way to you.
The unit was shipped with DHL. Please see attached shipping documents.
A lot of work was put into designing, building, and shipping that unit. We believe you will enjoy it very much.
If you have any questions feel free to contact us at [email protected].
Best Regards,
Katya Penkar
Sales Coordinator
Spondoolies-Tech LTD.
Tel.: +972(8)8606636
Fax : +972 (8)8643050
Mobile: +972(54)4882443
That is something else then Black Arrow...djeees
June 01, 2014, 02:40:28 PM
The UCoustic™ 9210 rack cabinets are amazing. I have two of the 24U active model. I can't hear my SP10.
Thanks!
What about heat? How many SP10 were you able to fit into 24U without any heat issues?
I highly appreciate your help, thanks again.
June 01, 2014, 02:27:51 PM
Hosting for SP10 was added back
Thanks! Typical that BTC has a 10% selloff as I about to pull the trigger. Need to wait until we recover.
Pull faster (or don't attempt to draw, so it will go higher
) June 01, 2014, 01:56:36 PM
Hosting for SP10 was added back
Thanks! Typical that BTC has a 10% selloff as I about to pull the trigger. Need to wait until we recover.
June 01, 2014, 01:55:43 PM
I have a late May unit, and it's only averaging ~1300 GH/s at the pool (BtcGuild) using the "turbo fans, highest rate" setting. Is there anything I can do to increase performance?
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
I have the same thing on 2 units.
This is why the +- 10% is for. There will always be some manufacturing differences.
If you're unhappy with your miner performance, please contact sales@ and we'll work something out.
June 01, 2014, 01:52:48 PM
I have a late May unit, and it's only averaging ~1300 GH/s at the pool (BtcGuild) using the "turbo fans, highest rate" setting. Is there anything I can do to increase performance?
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
I have the same thing on 2 units.
June 01, 2014, 01:27:58 PM
I have a late May unit, and it's only averaging ~1300 GH/s at the pool (BtcGuild) using the "turbo fans, highest rate" setting. Is there anything I can do to increase performance?
This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
Did you try with the overclock instructions on spondoolies website? This unit is running in a data center using 208v power, and temperatures are good (27C front, 69C back). I was expecting a bit more, so hopefully there are tweaks I can make to increase performance and this isn't just a low performing unit.
Jump to: