[ANN] Technobit HEX8A1 -240 GHs Coincraft A1 board- Finished production

Mitak

full member

Activity: 126

Merit: 100

Try removing the fuse
the diode type component soldered on the PCI-e connector.
Just cut it out, if this is not helping , then you have to trow/RMa the board

PMB

member

Activity: 109

Merit: 10

Quote from: gcube1305 on February 22, 2015, 06:59:30 PM

You're right...
Maybe it is just a little transistor or resistor, i will try to identify it, but i have'nt seen any burn mark on the board.

Is marto74 offering a kind of warranty on this ? Cheesy

Hi,

I have a similar problem, the board doesn't hash at all it is recognized in cgminer but it does not POWER UP. The fans do not work at all... Is there a fuse of some kind that I can replace? marto74 is awol so no use asking him for help...

I don't see any burn marks on my board also...

regards,

P.

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: gcube1305 on February 22, 2015, 06:59:30 PM

...........

You're right...
Maybe it is just a little transistor or resistor, i will try to identify it, but i have'nt seen any burn mark on the board.

Is marto74 offering a kind of warranty on this ? Cheesy

There is warranty, but i am not sure how long the warranty period Cheesy

gcube1305

full member

Activity: 155

Merit: 100

Quote from: Zich on February 22, 2015, 06:49:55 PM

Quote from: gcube1305 on February 22, 2015, 06:43:19 PM

Quote from: Zich on February 22, 2015, 06:27:33 PM

Quote from: gcube1305 on February 22, 2015, 07:26:15 AM

...........................

I have unplug the board last night, and replug it this morning, without any result. The board is not hot at all. There is absolutely no burn mark on the board.

Here is the CGMiner API log (a few minutes after a restart of tplink) (for information, error rate is 0 because of tplink reboot; after many hours i have never seen error rate over 0.1%, most of the times it is between 0.01 and 0.08) :

..............

Try change the frequency to 230 or 240 & the voltage to 1000. If the board still not hashing, then that board is ruined.

Still not hashing at 230/1000 and 240/1000...

Is it possible that only one A1 chip is dead ? In this case, maybe i can still use it with the good chip mask.

From your first cgminer api log, all chip is not hashing. So chips mask not gonna work.

You're right...
Maybe it is just a little transistor or resistor, i will try to identify it, but i have'nt seen any burn mark on the board.

Is marto74 offering a kind of warranty on this ? Cheesy

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: gcube1305 on February 22, 2015, 06:43:19 PM

Quote from: Zich on February 22, 2015, 06:27:33 PM

Quote from: gcube1305 on February 22, 2015, 07:26:15 AM

...........................

I have unplug the board last night, and replug it this morning, without any result. The board is not hot at all. There is absolutely no burn mark on the board.

Here is the CGMiner API log (a few minutes after a restart of tplink) (for information, error rate is 0 because of tplink reboot; after many hours i have never seen error rate over 0.1%, most of the times it is between 0.01 and 0.08) :

..............

Try change the frequency to 230 or 240 & the voltage to 1000. If the board still not hashing, then that board is ruined.

Still not hashing at 230/1000 and 240/1000...

Is it possible that only one A1 chip is dead ? In this case, maybe i can still use it with the good chip mask.

From your first cgminer api log, all chip is not hashing. So chips mask not gonna work.

gcube1305

full member

Activity: 155

Merit: 100

Quote from: Zich on February 22, 2015, 06:27:33 PM

Quote from: gcube1305 on February 22, 2015, 07:26:15 AM

...........................

I have unplug the board last night, and replug it this morning, without any result. The board is not hot at all. There is absolutely no burn mark on the board.

Here is the CGMiner API log (a few minutes after a restart of tplink) (for information, error rate is 0 because of tplink reboot; after many hours i have never seen error rate over 0.1%, most of the times it is between 0.01 and 0.08) :

..............

Try change the frequency to 230 or 240 & the voltage to 1000. If the board still not hashing, then that board is ruined.

I have just realized that this board has been hashing for one year exactly (first hash on feb 21, 2014, last hash on feb 21, 2015)... strange coincidence...

gcube1305

full member

Activity: 155

Merit: 100

Quote from: Zich on February 22, 2015, 06:27:33 PM

Quote from: gcube1305 on February 22, 2015, 07:26:15 AM

...........................

I have unplug the board last night, and replug it this morning, without any result. The board is not hot at all. There is absolutely no burn mark on the board.

Here is the CGMiner API log (a few minutes after a restart of tplink) (for information, error rate is 0 because of tplink reboot; after many hours i have never seen error rate over 0.1%, most of the times it is between 0.01 and 0.08) :

..............

Try change the frequency to 230 or 240 & the voltage to 1000. If the board still not hashing, then that board is ruined.

Still not hashing at 230/1000 and 240/1000...

Is it possible that only one A1 chip is dead ? In this case, maybe i can still use it with the good chip mask.

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: gcube1305 on February 22, 2015, 07:26:15 AM

...........................

I have unplug the board last night, and replug it this morning, without any result. The board is not hot at all. There is absolutely no burn mark on the board.

Here is the CGMiner API log (a few minutes after a restart of tplink) (for information, error rate is 0 because of tplink reboot; after many hours i have never seen error rate over 0.1%, most of the times it is between 0.01 and 0.08) :

..............

Try change the frequency to 230 or 240 & the voltage to 1000. If the board still not hashing, then that board is ruined.

loshia

legendary

Activity: 1610

Merit: 1000

The voltage is read through usb when nonce comes
As long as board is not hashing nonces get recived va usb.it will stay constant...that is the answer.

gcube1305

full member

Activity: 155

Merit: 100

gcube1305

full member

Activity: 155

Merit: 100

Quote from: Zich on February 22, 2015, 06:53:57 AM

Quote from: gcube1305 on February 22, 2015, 06:01:57 AM

Hi all,

I have a problem with an HEX8A1 board.

I have two HEX8A1 boards. I have change the fans since it was way too noisy, and i use a 220/920 setting. The two boards are linked to a TPlink router with openwrt ("OpenWrt Barrier Breaker r40295", i think it is a 0.3.0) through an USB hub. All (tplink and boards, hub is not externally powered) are powered with the same Corsair CX760.

This was working like a charm for the last 6 months. But since two days now, one of the board is not hashing anymore.

Everything looks fine, the board is seen by cgminer, when i plug/unplug it i can see the board disappearing/reappearing, but the hashrate is always 0. The second board is working and hashing. The led are the same on the two boards.

I have tried to plug only one board, i have tried 210/860, i have change the usb port, i have plug the faultly board directly to the TPlink, i have reset settings to 260/1000, but nothing worked.

I don't think it is a overheat problem, cause the fans are identicall on the two boards, and with those fans and settings the boards seems cooler than with the noisy sunon and 260/1000 settings (i can put my finger on the it for more than 10s Wink

). Moreover, i have a very very low error rate, and i did not change anything on the configuration for the last 6 months (and the room is at 18°).

Any idea ?
How can i see if it is a overheat problem ?

Seem like hardware problem. Try to let the board cool down for few hours, check if there is any hardware burn mark. Then try again. Then please post cgminer api log.

I have unplug the board last night, and replug it this morning, without any result. The board is not hot at all. There is absolutely no burn mark on the board.

Here is the CGMiner API log (a few minutes after a restart of tplink) (for information, error rate is 0 because of tplink reboot; after many hours i have never seen error rate over 0.1%, most of the times it is between 0.01 and 0.08) :

Code:

[Firmware Version] => 20140328
cgminer: 4_1_0_afb9743
Reply was 'STATUS=S,When=1424607810,Code=70,Msg=CGMiner stats,Description=cgminer 4.2.1|STATS=0,ID=HEX80,Enabled=Y,Status=Alive,Elapsed=510,MHS 5s=262.5G,MHS av=238.2G,Hardware Errors=0,Hardware Errors%=0.0000,USB Read Errors=0,USB Write Errors=0,USB Reset Count=0,Last Share Time=1424607807,Chip Count=8,Frequency=220,Core Voltage=920,PIC Voltage Readings=930,Chip1 Nonces=34,Chip1 Engines=30,Chip1 Dupes=0,Chip2 Nonces=25,Chip2 Engines=32,Chip2 Dupes=0,Chip3 Nonces=25,Chip3 Engines=32,Chip3 Dupes=0,Chip4 Nonces=27,Chip4 Engines=32,Chip4 Dupes=0,Chip5 Nonces=25,Chip5 Engines=32,Chip5 Dupes=0,Chip6 Nonces=33,Chip6 Engines=32,Chip6 Dupes=0,Chip7 Nonces=26,Chip7 Engines=32,Chip7 Dupes=0,Chip8 Nonces=26,Chip8 Engines=32,Chip8 Dupes=0|STATS=1,ID=HEX81,Enabled=Y,Status=Alive,Elapsed=510,MHS 5s=0.000,MHS av=0.000,Hardware Errors=0,Hardware Errors%=0.0000,USB Read Errors=0,USB Write Errors=0,USB Reset Count=0,Last Share Time=0,Chip Count=8,Frequency=220,Core Voltage=920,PIC Voltage Readings=800,Chip1 Nonces=0,Chip1 Engines=0,Chip1 Dupes=0,Chip2 Nonces=0,Chip2 Engines=0,Chip2 Dupes=0,Chip3 Nonces=0,Chip3 Engines=0,Chip3 Dupes=0,Chip4 Nonces=0,Chip4 Engines=0,Chip4 Dupes=0,Chip5 Nonces=0,Chip5 Engines=0,Chip5 Dupes=0,Chip6 Nonces=0,Chip6 Engines=0,Chip6 Dupes=0,Chip7 Nonces=0,Chip7 Engines=0,Chip7 Dupes=0,Chip8 Nonces=0,Chip8 Engines=0,Chip8 Dupes=0|STATS=2,ID=POOL0,Elapsed=510,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=128.00000000,Min Diff=128.00000000,Max Diff=128.00000000,Min Diff Count=398,Max Diff Count=398,Times Sent=223,Bytes Sent=26248,Times Recv=246,Bytes Recv=30822,Net Bytes Sent=26248,Net Bytes Recv=30822|STATS=3,ID=POOL1,Elapsed=510,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=0.00000000,Min Diff=0.00000000,Max Diff=0.00000000,Min Diff Count=0,Max Diff Count=0,Times Sent=0,Bytes Sent=0,Times Recv=0,Bytes Recv=0,Net Bytes Sent=0,Net Bytes Recv=0|STATS=4,ID=POOL2,Elapsed=510,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=0.00000000,Min Diff=0.00000000,Max Diff=0.00000000,Min Diff Count=0,Max Diff Count=0,Times Sent=0,Bytes Sent=0,Times Recv=0,Bytes Recv=0,Net Bytes Sent=0,Net Bytes Recv=0|'
[STATUS] =>
(
   [STATUS] => S
   [When] => 1424607810
   [Code] => 70
   [Msg] => CGMiner stats
   [Description] => cgminer 4.2.1
)
[STATS0] =>
(
   [STATS] => 0
   [ID] => HEX80
   [Enabled] => Y
   [Status] => Alive
   [Elapsed] => 510
   [MHS 5s] => 262.5G
   [MHS av] => 238.2G
   [Hardware Errors] => 0
   [Hardware Errors%] => 0.0000
   [USB Read Errors] => 0
   [USB Write Errors] => 0
   [USB Reset Count] => 0
   [Last Share Time] => 1424607807
   [Chip Count] => 8
   [Frequency] => 220
   [Core Voltage] => 920
   [PIC Voltage Readings] => 930
   [Chip1 Nonces] => 34
   [Chip1 Engines] => 30
   [Chip1 Dupes] => 0
   [Chip2 Nonces] => 25
   [Chip2 Engines] => 32
   [Chip2 Dupes] => 0
   [Chip3 Nonces] => 25
   [Chip3 Engines] => 32
   [Chip3 Dupes] => 0
   [Chip4 Nonces] => 27
   [Chip4 Engines] => 32
   [Chip4 Dupes] => 0
   [Chip5 Nonces] => 25
   [Chip5 Engines] => 32
   [Chip5 Dupes] => 0
   [Chip6 Nonces] => 33
   [Chip6 Engines] => 32
   [Chip6 Dupes] => 0
   [Chip7 Nonces] => 26
   [Chip7 Engines] => 32
   [Chip7 Dupes] => 0
   [Chip8 Nonces] => 26
   [Chip8 Engines] => 32
   [Chip8 Dupes] => 0
)
[STATS1] =>
(
   [STATS] => 1
   [ID] => HEX81
   [Enabled] => Y
   [Status] => Alive
   [Elapsed] => 510
   [MHS 5s] => 0.000
   [MHS av] => 0.000
   [Hardware Errors] => 0
   [Hardware Errors%] => 0.0000
   [USB Read Errors] => 0
   [USB Write Errors] => 0
   [USB Reset Count] => 0
   [Last Share Time] => 0
   [Chip Count] => 8
   [Frequency] => 220
   [Core Voltage] => 920
   [PIC Voltage Readings] => 800
   [Chip1 Nonces] => 0
   [Chip1 Engines] => 0
   [Chip1 Dupes] => 0
   [Chip2 Nonces] => 0
   [Chip2 Engines] => 0
   [Chip2 Dupes] => 0
   [Chip3 Nonces] => 0
   [Chip3 Engines] => 0
   [Chip3 Dupes] => 0
   [Chip4 Nonces] => 0
   [Chip4 Engines] => 0
   [Chip4 Dupes] => 0
   [Chip5 Nonces] => 0
   [Chip5 Engines] => 0
   [Chip5 Dupes] => 0
   [Chip6 Nonces] => 0
   [Chip6 Engines] => 0
   [Chip6 Dupes] => 0
   [Chip7 Nonces] => 0
   [Chip7 Engines] => 0
   [Chip7 Dupes] => 0
   [Chip8 Nonces] => 0
   [Chip8 Engines] => 0
   [Chip8 Dupes] => 0
)
[STATS2] =>
(
   [STATS] => 2
   [ID] => POOL0
   [Elapsed] => 510
   [Calls] => 0
   [Wait] => 0.000000
   [Max] => 0.000000
   [Min] => 99999999.000000
   [Pool Calls] => 0
   [Pool Attempts] => 0
   [Pool Wait] => 0.000000
   [Pool Max] => 0.000000
   [Pool Min] => 99999999.000000
   [Pool Av] => 0.000000
   [Work Had Roll Time] => false
   [Work Can Roll] => false
   [Work Had Expire] => false
   [Work Roll Time] => 0
   [Work Diff] => 128.00000000
   [Min Diff] => 128.00000000
   [Max Diff] => 128.00000000
   [Min Diff Count] => 398
   [Max Diff Count] => 398
   [Times Sent] => 223
   [Bytes Sent] => 26248
   [Times Recv] => 246
   [Bytes Recv] => 30822
   [Net Bytes Sent] => 26248
   [Net Bytes Recv] => 30822
)
[STATS3] =>
(
   [STATS] => 3
   [ID] => POOL1
   [Elapsed] => 510
   [Calls] => 0
   [Wait] => 0.000000
   [Max] => 0.000000
   [Min] => 99999999.000000
   [Pool Calls] => 0
   [Pool Attempts] => 0
   [Pool Wait] => 0.000000
   [Pool Max] => 0.000000
   [Pool Min] => 99999999.000000
   [Pool Av] => 0.000000
   [Work Had Roll Time] => false
   [Work Can Roll] => false
   [Work Had Expire] => false
   [Work Roll Time] => 0
   [Work Diff] => 0.00000000
   [Min Diff] => 0.00000000
   [Max Diff] => 0.00000000
   [Min Diff Count] => 0
   [Max Diff Count] => 0
   [Times Sent] => 0
   [Bytes Sent] => 0
   [Times Recv] => 0
   [Bytes Recv] => 0
   [Net Bytes Sent] => 0
   [Net Bytes Recv] => 0
)
[STATS4] =>
(
   [STATS] => 4
   [ID] => POOL2
   [Elapsed] => 510
   [Calls] => 0
   [Wait] => 0.000000
   [Max] => 0.000000
   [Min] => 99999999.000000
   [Pool Calls] => 0
   [Pool Attempts] => 0
   [Pool Wait] => 0.000000
   [Pool Max] => 0.000000
   [Pool Min] => 99999999.000000
   [Pool Av] => 0.000000
   [Work Had Roll Time] => false
   [Work Can Roll] => false
   [Work Had Expire] => false
   [Work Roll Time] => 0
   [Work Diff] => 0.00000000
   [Min Diff] => 0.00000000
   [Max Diff] => 0.00000000
   [Min Diff Count] => 0
   [Max Diff Count] => 0
   [Times Sent] => 0
   [Bytes Sent] => 0
   [Times Recv] => 0
   [Bytes Recv] => 0
   [Net Bytes Sent] => 0
   [Net Bytes Recv] => 0
)

[/code]

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: gcube1305 on February 22, 2015, 06:01:57 AM

Hi all,

I have a problem with an HEX8A1 board.

I have two HEX8A1 boards. I have change the fans since it was way too noisy, and i use a 220/920 setting. The two boards are linked to a TPlink router with openwrt ("OpenWrt Barrier Breaker r40295", i think it is a 0.3.0) through an USB hub. All (tplink and boards, hub is not externally powered) are powered with the same Corsair CX760.

This was working like a charm for the last 6 months. But since two days now, one of the board is not hashing anymore.

Everything looks fine, the board is seen by cgminer, when i plug/unplug it i can see the board disappearing/reappearing, but the hashrate is always 0. The second board is working and hashing. The led are the same on the two boards.

I have tried to plug only one board, i have tried 210/860, i have change the usb port, i have plug the faultly board directly to the TPlink, i have reset settings to 260/1000, but nothing worked.

I don't think it is a overheat problem, cause the fans are identicall on the two boards, and with those fans and settings the boards seems cooler than with the noisy sunon and 260/1000 settings (i can put my finger on the it for more than 10s Wink

). Moreover, i have a very very low error rate, and i did not change anything on the configuration for the last 6 months (and the room is at 18°).

Any idea ?
How can i see if it is a overheat problem ?

Seem like hardware problem. Try to let the board cool down for few hours, check if there is any hardware burn mark. Then try again. Then please post cgminer api log.

gcube1305

full member

Activity: 155

Merit: 100

Hi all,

I have a problem with an HEX8A1 board.

I have two HEX8A1 boards. I have change the fans since it was way too noisy, and i use a 220/920 setting. The two boards are linked to a TPlink router with openwrt ("OpenWrt Barrier Breaker r40295", i think it is a 0.3.0) through an USB hub. All (tplink and boards, hub is not externally powered) are powered with the same Corsair CX760.

This was working like a charm for the last 6 months. But since two days now, one of the board is not hashing anymore.

Everything looks fine, the board is seen by cgminer, when i plug/unplug it i can see the board disappearing/reappearing, but the hashrate is always 0. The second board is working and hashing. The led are the same on the two boards.

I have tried to plug only one board, i have tried 210/860, i have change the usb port, i have plug the faultly board directly to the TPlink, i have reset settings to 260/1000, but nothing worked.

I don't think it is a overheat problem, cause the fans are identicall on the two boards, and with those fans and settings the boards seems cooler than with the noisy sunon and 260/1000 settings (i can put my finger on the it for more than 10s Wink

). Moreover, i have a very very low error rate, and i did not change anything on the configuration for the last 6 months (and the room is at 18°).

Any idea ?
How can i see if it is a overheat problem ?

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: cryptonit on January 11, 2015, 10:24:45 AM

is there any sweet spot at underclocking this hw or is it time to sort them out?
if there any answer please PM me so i dont miss it

i run them now 860 210

Unfortunately, that's already the lowest setting.

cryptonit

legendary

Activity: 3052

Merit: 1053

bit.diamonds | uNiq.diamonds

is there any sweet spot at underclocking this hw or is it time to sort them out?
if there any answer please PM me so i dont miss it

i run them now 860 210

2GOOD

hero member

Activity: 547

Merit: 531

First bits: 12good

HEX8 needs atleast 860mV to start, if not try 866mV

Buchi-88

legendary

Activity: 4004

Merit: 2702

Quote from: Zich on December 08, 2014, 02:09:53 AM

Quote from: Buchi-88 on December 07, 2014, 08:41:54 AM

@Zich

I think it's not a problem with the heat, the miner doesn't start??

The same problem with Hotplug:

.....

Are you using any usb hub? Try to plug it directly to Rpi.
Did Rpi use same power source with miner?
Try to change the usb cable.
Clean the board from dirt then visual check the component.

THX for your answer,

i will test your suggestions, and where appropriate make photos Wink

a time he hashte again today when hotplugin, but after another hotplugin the same...

regards

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: Buchi-88 on December 07, 2014, 08:41:54 AM

@Zich

I think it's not a problem with the heat, the miner doesn't start??

The same problem with Hotplug:

.....

Are you using any usb hub? Try to plug it directly to Rpi.
Did Rpi use same power source with miner?
Try to change the usb cable.
Clean the board from dirt then visual check the component.

Buchi-88

legendary

Activity: 4004

Merit: 2702

@Zich

I think it's not a problem with the heat, the miner doesn't start??

The same problem with Hotplug:

Quote

cgminer version 4.4.2 - Started: [2014-12-07 14:17:00]
--------------------------------------------------------------------------------
(5s):0.000 (1m):0.000 (5m):0.000 (15m):0.000 (avg):0.000h/s
ST: 3 SS: 0 NB: 8 LW: 653 GF: 1 RF: 0
Connected to miner-control.de diff 16 with stratum as user NTYNy7JWo1LyK9Z51ZxdcpsdzEpfT5C6VV
Block: 2e05d06d... Diff:1.01M Started: [14:33:59] Best share: 0
--------------------------------------------------------------------------------
USB management Pool management Settings Display options Quit
2: HEX8 2 : 220 850/ 800mV | A:0 R:0/0.00% HW:0/0.00%
--------------------------------------------------------------------------------
[2014-12-07 14:17:00] Pool 1 difficulty changed to 16
[2014-12-07 14:17:00] Network diff set to 1.07M
[2014-12-07 14:17:05] API running in IP access mode on port 4029 (11)
[2014-12-07 14:19:59] Network diff set to 1.03M
[2014-12-07 14:19:59] Stratum from pool 0 detected new block
[2014-12-07 14:23:22] Network diff set to 1.02M
[2014-12-07 14:23:22] Stratum from pool 0 detected new block
[2014-12-07 14:23:36] Network diff set to 1.03M
[2014-12-07 14:23:36] Stratum from pool 0 detected new block
[2014-12-07 14:25:26] Network diff set to 1.05M
[2014-12-07 14:25:26] Stratum from pool 0 detected new block
[2014-12-07 14:26:08] Network diff set to 1.05M
[2014-12-07 14:26:08] Stratum from pool 0 detected new block
[2014-12-07 14:27:08] Stratum connection to pool 0 interrupted
[2014-12-07 14:27:08] Pool 0 difficulty changed to 16
[2014-12-07 14:30:03] Network diff set to 1.03M
[2014-12-07 14:30:03] Stratum from pool 0 detected new block
[2014-12-07 14:33:59] Network diff set to 1.01M
[2014-12-07 14:33:59] Stratum from pool 0 detected new block
[2014-12-07 14:34:04] HEX8 0 failure, disabling!
[2014-12-07 14:34:24] Hotplug: hexminer8 added HEX8 1
[2014-12-07 14:34:37] HEX8 1 failure, disabling!
[2014-12-07 14:34:50] Hotplug: hexminer8 added HEX8 2

@Biffa

I don't think so the same problem with one instance....

config:

Quote

"hexminer8-set-diff-to-one" : "0",
"hexminer8-chip-mask" : "255",
"hexminer8-voltage" : "850",
"hexminer8-options" : "8:220",
"set_default_to_8" : true

All lights light on the miner, where can i search the defect? THX

regards

Biffa

legendary

Activity: 3234

Merit: 1221

Could also be that the pi just doesn't have enough grunt to run two copies of cgminer at the same time.

Topic: [ANN] Technobit HEX8A1 -240 GHs Coincraft A1 board- Finished production (Read 72437 times)