[ANN] Technobit HEX8A1 -240 GHs Coincraft A1 board- Finished production - page 23.

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: eestimees on March 07, 2014, 03:49:51 PM

Quote from: Gator-hex on March 07, 2014, 03:44:20 PM

Quote from: eestimees on March 07, 2014, 03:40:06 PM

Quote from: Gator-hex on March 07, 2014, 03:37:01 PM

Quote from: eestimees on March 07, 2014, 03:34:32 PM

Quote from: marto74 on March 07, 2014, 03:31:25 PM

what lights are on on on your device ?
There is a green , orange and red

green and orange are on

What power supply are you using and does it have enough available power?
I had problems running 2x Hex8A1 until I put a fan on the 5V line to help regulate my ThermalTake 730W PSU.
These chips won't fire up if they cannot get enough power.

1200W single rail Aurum PRO, two separate PCI-e power cables connected to hex8a1 nothing more behind that PSU

Silly question, you did put the paper clip in the motherboard connector between the green and black wire? Try taking it out and putting it back in (that resets a PSU after failsafe)
If that's not it, try plugging something in that uses 5V power. I just put a 12V fan on the Red/Black molex cable wires.

changed PSU, that is not the case.. no paper clip I have a switch there: http://cytron.com.my/viewProduct.php?pcode=BB-ATXRA&name=Breakout%20Board%20ATX%20Right%20Angle

router (MR3020) that is for miner, can ping and resolve names.. ok debuggin that network a bit more...

Can you tell me what your issue is?
I missed it...
Please post Lsusb output from ssh small l lsusb
Screen -r also ?

eestimees

hero member

Activity: 651

Merit: 500

Quote from: Gator-hex on March 07, 2014, 03:44:20 PM

Quote from: eestimees on March 07, 2014, 03:40:06 PM

Quote from: Gator-hex on March 07, 2014, 03:37:01 PM

Quote from: eestimees on March 07, 2014, 03:34:32 PM

Quote from: marto74 on March 07, 2014, 03:31:25 PM

what lights are on on on your device ?
There is a green , orange and red

green and orange are on

What power supply are you using and does it have enough available power?
I had problems running 2x Hex8A1 until I put a fan on the 5V line to help regulate my ThermalTake 730W PSU.
These chips won't fire up if they cannot get enough power.

1200W single rail Aurum PRO, two separate PCI-e power cables connected to hex8a1 nothing more behind that PSU

Silly question, you did put the paper clip in the motherboard connector between the green and black wire? Try taking it out and putting it back in (that resets a PSU after failsafe)
If that's not it, try plugging something in that uses 5V power. I just put a 12V fan on the Red/Black molex cable wires.

changed PSU, that is not the case.. no paper clip I have a switch there: http://cytron.com.my/viewProduct.php?pcode=BB-ATXRA&name=Breakout%20Board%20ATX%20Right%20Angle

router (MR3020) that is for miner, can ping and resolve names.. ok debuggin that network a bit more...

Gator-hex

hero member

Activity: 490

Merit: 500

Quote from: eestimees on March 07, 2014, 03:40:06 PM

Quote from: Gator-hex on March 07, 2014, 03:37:01 PM

Quote from: eestimees on March 07, 2014, 03:34:32 PM

Quote from: marto74 on March 07, 2014, 03:31:25 PM

what lights are on on on your device ?
There is a green , orange and red

green and orange are on

What power supply are you using and does it have enough available power?
I had problems running 2x Hex8A1 until I put a fan on the 5V line to help regulate my ThermalTake 730W PSU.
These chips won't fire up if they cannot get enough power.

1200W single rail Aurum PRO, two separate PCI-e power cables connected to hex8a1 nothing more behind that PSU

Silly question, you did put the paper clip in the motherboard connector between the green and black wire?
Try taking it out and putting it back in (that resets a PSU after failsafe shutdown)
If that's not it, try plugging something in that uses 5V power. I just put a 12V fan into the 5V Red/Black molex cable wires.
My PSU kept going into failsafe shutdown until I put something on the 5V line.

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: Gator-hex on March 07, 2014, 03:33:33 PM

Quote from: marto74 on March 07, 2014, 03:31:25 PM

what lights are on on on your device ?
There is a green , orange and red

What does the orange light mean? I have one that's green-green and another one that's green-orange. Seems to work ok, but more power hungry.

Orange means shares dude Wink

Red is bad only. In the beginning it can flash but that is all if you see it after that work que is empty no work to board pool Is dead net issues or whatever

eestimees

hero member

Activity: 651

Merit: 500

Quote from: Gator-hex on March 07, 2014, 03:37:01 PM

Quote from: eestimees on March 07, 2014, 03:34:32 PM

Quote from: marto74 on March 07, 2014, 03:31:25 PM

what lights are on on on your device ?
There is a green , orange and red

green and orange are on

What power supply are you using and does it have enough available power?
I had problems running 2x Hex8A1 until I put a fan on the 5V line to help regulate my ThermalTake 730W PSU.
These chips won't fire up if they cannot get enough power.

1200W single rail Aurum PRO, two separate PCI-e power cables connected to hex8a1 nothing more behind that PSU

Gator-hex

hero member

Activity: 490

Merit: 500

Quote from: eestimees on March 07, 2014, 03:34:32 PM

Quote from: marto74 on March 07, 2014, 03:31:25 PM

what lights are on on on your device ?
There is a green , orange and red

green and orange are on

What power supply are you using and does it have enough available power?
I had problems running 2x Hex8A1 until I put a fan on the 5V line to help regulate my ThermalTake 730W PSU.
These chips won't fire up if they cannot get enough power.

eestimees

hero member

Activity: 651

Merit: 500

Quote from: marto74 on March 07, 2014, 03:31:25 PM

what lights are on on on your device ?
There is a green , orange and red

green and orange are on

Gator-hex

hero member

Activity: 490

Merit: 500

Quote from: marto74 on March 07, 2014, 03:31:25 PM

what lights are on on on your device ?
There is a green , orange and red

What does the orange light mean? I have one that's green-green and another one that's green-orange. Seems to work ok, but more power hungry.

marto74

hero member

Activity: 728

Merit: 500

what lights are on on on your device ?
There is a green , orange and red

eestimees

hero member

Activity: 651

Merit: 500

Quote from: Gator-hex on March 07, 2014, 03:21:33 PM

Is your Hex8A1 plugged directly into the TP-Link TL-3020 or through a USB hub?

Try plugging it in directly and see if it works. USB might be leaking power and power protection hub will stop it communicating.

it is directly connected.
flashed it again w 0_2_2 fw

EDIT: changed the usb cable, nothing better...

Gator-hex

hero member

Activity: 490

Merit: 500

Is your Hex8A1 plugged directly into the TP-Link TL-3020 or through a USB hub?

Try plugging it in directly and see if it works. USB might be leaking power and power protection hub will stop it communicating.

eestimees

hero member

Activity: 651

Merit: 500

Quote from: marto74 on March 07, 2014, 03:14:59 PM

put something in all boxes even for hexu - 54

also please change dificulty seting to 0

also switch to stratum.btcguild.com:3333

also tried that before writing here:

marto74

hero member

Activity: 728

Merit: 500

put something in all boxes even for hexu - 54

also please change dificulty seting to 0

also switch to stratum.btcguild.com:3333

eestimees

hero member

Activity: 651

Merit: 500

Quote from: Gator-hex on March 07, 2014, 03:11:34 PM

Quote from: eestimees on March 07, 2014, 03:09:28 PM

Quote from: Gator-hex on March 07, 2014, 03:07:25 PM

xxx.btcguild.com is not a reachable address.

it's not xxx it is changed before pasting it here.

EDIT: it can connect to pool "Pool 0 difficulty changed to 256" as this comes from pool worker settings

That setting should be...

eu-stratum.btcguild.com:3333

if your're in the EU.

that is not the case, but for your sake I can change it on not mask it with "xxx":

Code:

cgminer version 4.0.0 - Started: [2014-03-07 22:13:10]
------------------------------------------------------------------------------------------
(5s):0.000 (avg):0.000h/s | A:0 R:0 HW:0 WU:0.0/m
ST: 2 SS: 0 NB: 1 LW: 93 GF: 0 RF: 0
Connected to eu-stratum.btcguild.com diff 2 with stratum as user xxx
Block: 59ca2446... Diff:3.82G Started: [22:13:10] Best share: 0
------------------------------------------------------------------------------------------
[U]SB device management [P]ool management [S]ettings [D]isplay options [Q]uit
000: HEX8 0: 260 1000/ 800mV | 0.000/ 0.000h/s | A:0 R:0/0.00% HW:0/0.00% WU:0.0/m
------------------------------------------------------------------------------------------
[2014-03-07 22:12:11] Started cgminer 4.0.0
[2014-03-07 22:12:12] Probing for an alive pool
[2014-03-07 22:12:22] Waiting for work to be available from pools.
[2014-03-07 22:12:59] Pool 0 difficulty changed to 2
[2014-03-07 22:13:10] Network diff set to 3.82G
[2014-03-07 22:13:10] Work available from pools, resuming.
[2014-03-07 22:13:15] API running in IP access mode on port 4028 (11)

Gator-hex

hero member

Activity: 490

Merit: 500

Quote from: eestimees on March 07, 2014, 03:09:28 PM

Quote from: Gator-hex on March 07, 2014, 03:07:25 PM

xxx.btcguild.com is not a reachable address.

it's not xxx it is changed before pasting it here.

EDIT: it can connect to pool "Pool 0 difficulty changed to 256" as this comes from pool worker settings

That setting should be...

eu-stratum.btcguild.com:3333

if you're in the EU.

eestimees

hero member

Activity: 651

Merit: 500

Quote from: Gator-hex on March 07, 2014, 03:07:25 PM

xxx.btcguild.com is not a reachable address.

it's not xxx it is changed before pasting it here.

EDIT: it can connect to pool "Pool 0 difficulty changed to 256" as this comes from pool worker settings

Gator-hex

hero member

Activity: 490

Merit: 500

xxx.btcguild.com is not a reachable address.

eestimees

hero member

Activity: 651

Merit: 500

Quote from: Gator-hex on March 07, 2014, 02:58:23 PM

Quote from: eestimees on March 07, 2014, 02:54:00 PM

What I'm missing here:

cgminer monitor keeps restartin cgminer, and not hashing a thing.. using router MR3020

Did you change "Handle USB detect errors as (Default: hexA)" to Hex8?

yes, I did.

Gator-hex

hero member

Activity: 490

Merit: 500

Quote from: eestimees on March 07, 2014, 02:54:00 PM

What I'm missing here:

cgminer monitor keeps restartin cgminer, and not hashing a thing.. using router MR3020

Did you change "Handle USB detect errors as (Default: hexA)" to Hex8?

eestimees

hero member

Activity: 651

Merit: 500

What I'm missing here:

Code:

cgminer version 4.0.0 - Started: [2014-03-07 21:50:13]
------------------------------------------------------------------------------------------
(5s):0.000 (avg):0.000h/s | A:0 R:0 HW:0 WU:0.0/m
ST: 2 SS: 0 NB: 2 LW: 187 GF: 0 RF: 0
Connected to xxx.btcguild.com diff 256 with stratum as user xxx
Block: 89975df5... Diff:3.82G Started: [21:51:29] Best share: 0
------------------------------------------------------------------------------------------
[U]SB device management [P]ool management [S]ettings [D]isplay options [Q]uit
000: HEX8 0: 260 1000/ 800mV | 0.000/ 0.000h/s | A:0 R:0/0.00% HW:0/0.00% WU:0.0/m
------------------------------------------------------------------------------------------
[2014-03-07 21:50:11] Started cgminer 4.0.0
[2014-03-07 21:50:12] Probing for an alive pool
[2014-03-07 21:50:13] Pool 0 difficulty changed to 2
[2014-03-07 21:50:13] Pool 0 difficulty changed to 256
[2014-03-07 21:50:13] Network diff set to 3.82G
[2014-03-07 21:50:18] API running in IP access mode on port 4028 (11)
[2014-03-07 21:51:29] Stratum from pool 0 detected new block

Code:

[STATS0] =>
(
   [STATS] => 0
   [ID] => HEX80
   [Enabled] => Y
   [Status] => Alive
   [Elapsed] => 40
   [MHS 5s] => 0.000
   [MHS av] => 0.000
   [Hardware Errors] => 0
   [Hardware Errors%] => 0.0000
   [USB Read Errors] => 0
   [USB Write Errors] => 0
   [USB Reset Count] => 0
   [Last Share Time] => 0
   [Chip Count] => 8
   [Frequency] => 260
   [Core Voltage] => 1000
   [PIC Voltage Readings] => 800
   [Chip1 Nonces] => 0
   [Chip1 Engines] => 0
   [Chip1 Dupes] => 0
   [Chip2 Nonces] => 0
   [Chip2 Engines] => 0
   [Chip2 Dupes] => 0
   [Chip3 Nonces] => 0
   [Chip3 Engines] => 0
   [Chip3 Dupes] => 0
   [Chip4 Nonces] => 0
   [Chip4 Engines] => 0
   [Chip4 Dupes] => 0
   [Chip5 Nonces] => 0
   [Chip5 Engines] => 0
   [Chip5 Dupes] => 0
   [Chip6 Nonces] => 0
   [Chip6 Engines] => 0
   [Chip6 Dupes] => 0
   [Chip7 Nonces] => 0
   [Chip7 Engines] => 0
   [Chip7 Dupes] => 0
   [Chip8 Nonces] => 0
   [Chip8 Engines] => 0
   [Chip8 Dupes] => 0

cgminer monitor keeps restartin cgminer, and not hashing a thing.. using router MR3020

Topic: [ANN] Technobit HEX8A1 -240 GHs Coincraft A1 board- Finished production - page 23. (Read 72425 times)