Topic: ANTMINER C1 Discussion and Support Thread - page 61. (Read 129207 times)
new firmware update posted today one of the changes is increased voltage to 760 This is the fix you all are looking for so I suggest anyone with flaky performance on there C1's do this update. I pushed my voltage up to match the new update and my miner is running even better then it was a 745 volts
im getting 1th miner side but not pool side... I am using slush pool. Any thoughts?
Try a different pool.
im getting 1th miner side but not pool side... I am using slush pool. Any thoughts?
I'm using my Corsair, not the harness at all on all three of my rigs.
Before I even powered up my C1 Miner for the first time, I filled the cooling system
to leak test and I used an external power supply.. to power the cooling system 3x fans and the pump
I figured it would safer then trying to do it hot (live) with a 1000W Power supply
connected (@70A)
to leak test and I used an external power supply.. to power the cooling system 3x fans and the pump
I figured it would safer then trying to do it hot (live) with a 1000W Power supply
connected (@70A)
notlist3d was the one who came up with the idea for the Phobya fan board.
Well done.
To me, It doesn't make sense to run noisy fans and a noisy (mechanical) pump
thru one of your digital hashing boards (blades)
Well done.
To me, It doesn't make sense to run noisy fans and a noisy (mechanical) pump
thru one of your digital hashing boards (blades)
I'm still having issues with getting one of my miners to 1000TH/s. I've increased the voltage, added in three pools as Bitmain requested and this unit just doesn't want to hash where it is supposed to.
Also, anyone notice pressure build up in the loop? I wanted to check my coolant level, so I unscrewed the fill cap and it was like opening a can of soda. I know some pressure is caused by the heat, but these loops aren't made to handle the pressure, right....certainly not the pump.
Also, anyone notice pressure build up in the loop? I wanted to check my coolant level, so I unscrewed the fill cap and it was like opening a can of soda. I know some pressure is caused by the heat, but these loops aren't made to handle the pressure, right....certainly not the pump.
I have had much better luck maintaining that 1000TH/s performance level once I started powering the Radiator's 3x fans
and the Pump directly from the PSU instead of going thru one of the connectors on the C1 blades.
I too am using an external PSU to power the fans and pump.
M
I'm still having issues with getting one of my miners to 1000TH/s. I've increased the voltage, added in three pools as Bitmain requested and this unit just doesn't want to hash where it is supposed to.
Also, anyone notice pressure build up in the loop? I wanted to check my coolant level, so I unscrewed the fill cap and it was like opening a can of soda. I know some pressure is caused by the heat, but these loops aren't made to handle the pressure, right....certainly not the pump.
Also, anyone notice pressure build up in the loop? I wanted to check my coolant level, so I unscrewed the fill cap and it was like opening a can of soda. I know some pressure is caused by the heat, but these loops aren't made to handle the pressure, right....certainly not the pump.
I have had much better luck maintaining that 1000TH/s performance level once I started powering the Radiator's 3x fans
and the Pump directly from the PSU instead of going thru one of the connectors on the C1 blades.
I'm using a Corsair RM1000
and one of these:
Molex to 3 pin adapter (To use instead of syscooling harness):
http://www.amazon.com/Phobya-4-Pin-3-Pin-Splitter-Connection/dp/B007S3T4O0/ref=sr_1_3?ie=UTF8&qid=1416652659&sr=8-3&keywords=molex+to+fan
Your results may vary.
I was one to suggest http://www.amazon.com/Phobya-4-Pin-3-Pin-Splitter-Connection/dp/B007S3T4O0/ref=sr_1_3?ie=UTF8&qid=1416652659&sr=8-3&keywords=molex+to+fan instead of the syscooling harness. I can confirm it's still working away.
Still no RMA from syscooling.... ordering power and pump was a good decision elsewhere don't wait on syscooling RMA.
I'm still having issues with getting one of my miners to 1000TH/s. I've increased the voltage, added in three pools as Bitmain requested and this unit just doesn't want to hash where it is supposed to.
Also, anyone notice pressure build up in the loop? I wanted to check my coolant level, so I unscrewed the fill cap and it was like opening a can of soda. I know some pressure is caused by the heat, but these loops aren't made to handle the pressure, right....certainly not the pump.
Also, anyone notice pressure build up in the loop? I wanted to check my coolant level, so I unscrewed the fill cap and it was like opening a can of soda. I know some pressure is caused by the heat, but these loops aren't made to handle the pressure, right....certainly not the pump.
I have had much better luck maintaining that 1000TH/s performance level once I started powering the Radiator's 3x fans
and the Pump directly from the PSU instead of going thru one of the connectors on the C1 blades.
I'm using a Corsair RM1000
and one of these:
Molex to 3 pin adapter (To use instead of syscooling harness):
http://www.amazon.com/Phobya-4-Pin-3-Pin-Splitter-Connection/dp/B007S3T4O0/ref=sr_1_3?ie=UTF8&qid=1416652659&sr=8-3&keywords=molex+to+fan
Your results may vary.
I'm still having issues with getting one of my miners to 1000TH/s. I've increased the voltage, added in three pools as Bitmain requested and this unit just doesn't want to hash where it is supposed to.
Also, anyone notice pressure build up in the loop? I wanted to check my coolant level, so I unscrewed the fill cap and it was like opening a can of soda. I know some pressure is caused by the heat, but these loops aren't made to handle the pressure, right....certainly not the pump.
Also, anyone notice pressure build up in the loop? I wanted to check my coolant level, so I unscrewed the fill cap and it was like opening a can of soda. I know some pressure is caused by the heat, but these loops aren't made to handle the pressure, right....certainly not the pump.
*1000GH. Screenshots of the miners please.
Yes thats normal. You should typically leave the cap open when first turning on until running at a constant temp before closing.
I'm still having issues with getting one of my miners to 1000TH/s. I've increased the voltage, added in three pools as Bitmain requested and this unit just doesn't want to hash where it is supposed to.
Also, anyone notice pressure build up in the loop? I wanted to check my coolant level, so I unscrewed the fill cap and it was like opening a can of soda. I know some pressure is caused by the heat, but these loops aren't made to handle the pressure, right....certainly not the pump.
Also, anyone notice pressure build up in the loop? I wanted to check my coolant level, so I unscrewed the fill cap and it was like opening a can of soda. I know some pressure is caused by the heat, but these loops aren't made to handle the pressure, right....certainly not the pump.
This will be my 4th and 5th order coming from bitmain this time 2 orders.....
my xp they ALWAYS ship tue. morning ver vvery early (like 4am) USA time.
chill and email or skype them if you dont know whats up with your order but most things dont ship out before the weekends unless you order s3's and get lucky.
I'm so happy my c1 is humming again.
my xp they ALWAYS ship tue. morning ver vvery early (like 4am) USA time.
chill and email or skype them if you dont know whats up with your order but most things dont ship out before the weekends unless you order s3's and get lucky.
I'm so happy my c1 is humming again.
I ordered 1 C1 on 11-26-2014 and now I regret buying it. I have not received it and my order shows Unshipped as of now (12-1-2014). I should have purchased two S3+'s instead. I'd have received them by now. Is it possible to cancel the order, or modify your order to different miners?
Something is definitely wrong with your order. I ordered the same day as you and received mine last Wednesday.How is it possible that you say you received your miners on the 26th, when you ordered them on the 26th?
I noticed that on the C1 interface they have removed the HW column. Is it possible to calculate hardware errors from what they give us on the screen?
It's also listed in my Ant monitor. (See my sig.)
M
I ordered 1 C1 on 11-26-2014 and now I regret buying it. I have not received it and my order shows Unshipped as of now (12-1-2014). I should have purchased two S3+'s instead. I'd have received them by now. Is it possible to cancel the order, or modify your order to different miners?
This may seem odd ... but I ordered mine on 11/24 and I got it on 11/28. To the east coast of the US. UPS couldn't decide if it'd be delivered today (12/1) or Fri (11/28). It flopped back and forth a few times, but it arrived on 11/28.
M
I ordered 1 C1 on 11-26-2014 and now I regret buying it. I have not received it and my order shows Unshipped as of now (12-1-2014). I should have purchased two S3+'s instead. I'd have received them by now. Is it possible to cancel the order, or modify your order to different miners?
Something is definitely wrong with your order. I ordered the same day as you and received mine last Wednesday.How is it possible that you say you received your miners on the 26th, when you ordered them on the 26th?
Miner Teleportation?
While we are on the topic of that..can you beam down the updated firmware you said you would chase down bitmain for 
? I'm waiting, I'll check again tomorrow.
I ordered 1 C1 on 11-26-2014 and now I regret buying it. I have not received it and my order shows Unshipped as of now (12-1-2014). I should have purchased two S3+'s instead. I'd have received them by now. Is it possible to cancel the order, or modify your order to different miners?
Something is definitely wrong with your order. I ordered the same day as you and received mine last Wednesday.How is it possible that you say you received your miners on the 26th, when you ordered them on the 26th?
Miner Teleportation?
While we are on the topic of that..can you beam down the updated firmware you said you would chase down bitmain for ? I ordered 1 C1 on 11-26-2014 and now I regret buying it. I have not received it and my order shows Unshipped as of now (12-1-2014). I should have purchased two S3+'s instead. I'd have received them by now. Is it possible to cancel the order, or modify your order to different miners?
Something is definitely wrong with your order. I ordered the same day as you and received mine last Wednesday.How is it possible that you say you received your miners on the 26th, when you ordered them on the 26th?
I noticed that on the C1 interface they have removed the HW column. Is it possible to calculate hardware errors from what they give us on the screen?
The HWE are still there under the pools info same column now..and the % shows as well
Jump to: