Pages:
Author

Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 101. (Read 125911 times)

full member
Activity: 348
Merit: 119
how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%

Ok thanks!.

In the new version, when click "Apply".... nothing applies, i've started at 25% fan speed and 400mhz and I can't change the fan speed, all the chips at 90º degrees, i had to power off the machine and install the original version to set it a 70% and then install your firmware again. After a few tests nothing changes clicking apply, be careful with that.



Thank you for the feedback. Did you clear your browser cache?

yep and tried with an other one ,same issue , i tried remotly with my smartphone (port forward) same bug, nothing writen and miner do not reboot
sr. member
Activity: 336
Merit: 258
how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%

Ok thanks!.

In the new version, when click "Apply".... nothing applies, i've started at 25% fan speed and 400mhz and I can't change the fan speed, all the chips at 90º degrees, i had to power off the machine and install the original version to set it a 70% and then install your firmware again. After a few tests nothing changes clicking apply, be careful with that.



Thank you for the feedback. Did you clear your browser cache?
member
Activity: 118
Merit: 11
how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%

Ok thanks!.

In the new version, when click "Apply".... nothing applies, i've started at 25% fan speed and 400mhz and I can't change the fan speed, all the chips at 90º degrees, i had to power off the machine and install the original version to set it a 70% and then install your firmware again. After a few tests nothing changes clicking apply, be careful with that.

The issue is only in the "General Settings" page.

full member
Activity: 348
Merit: 119
have an issue , i set 25% before flash , seem to can't change it to lower then, webpage locked to "Waiting for changes to be applied..."
Seem to be global miner general configuration page
anyone same ?
try to change pool or just fan speed

advanced settings working good
sr. member
Activity: 336
Merit: 258
how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%
member
Activity: 118
Merit: 11
how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.
sr. member
Activity: 336
Merit: 258
sr. member
Activity: 800
Merit: 294
Created AutoTune to saved the planet! ~USA
Look if Baikal can do it I'm pretty sure the D3's can do it.... Watching this thread very closely.

Your an idiot. Baikal sells a Field Programmable Gate Array. Spartan FPGA or anything like that. You are an idiot. Just because one company can do it doesn't mean another could. That is like say you can drive a 18 wheeler like you can drive a boat. They both move you but one doesn't work in the other since it is not designed to do so.


I have got a new non standard answer from Bitmain.

Quote
The Antminer D3 has been designed and tested to mine DASH only. It can be used to mine other X11 coins as well but we cannot guarantee the performance or efficiency of the D3 miner when used to mine other X11 coins than DASH.

Best regards,
Joy
Bitmain
Always order products directly from our website: www.bitmain.com
"Solved" means we replied - we still work on your issue until it is resolved.


They just not garantee the performace, so they work on it.

Other x11 coins X11  aka

Dash (Darkcoin)

StartCoin

CannabisCoin

SmartCoin

ConspiracyCoin

Europecoin

GiveCoin

HashCoin

LimeXcoin

Logicoin

Muniti

Nyancoin

Quebecoin

XCurrency



The only benefit from this firmware is for the thread creator taking a fee. It does nothing you can't do already.

cant do ? so people are dumb , cause they dont share knowlege , cause it s impossible to find a tutorial -> how to set the fan down at : startup, switch pool , change setting in miner , etc ... and that the basic

we need that for other antminer , l3+, s9 etc.... i know a bit linux and i try to send cat in ssh with putty but this not result with usually cat editor , you just can see the text file
anyway blissz deserve fee for work and time, everyone are free dont agree and not using it.

It switches pools by default... Put in a few pools. When it loses it's connection to the pool it goes to the next. Or just use the built in api and you can have it switch to the most profitable coin.. Which guess what.... They only give you SSH access to the miners for a reason...

Dude just modify the miner settings lmao.
full member
Activity: 348
Merit: 119
Look if Baikal can do it I'm pretty sure the D3's can do it.... Watching this thread very closely.

Your an idiot. Baikal sells a Field Programmable Gate Array. Spartan FPGA or anything like that. You are an idiot. Just because one company can do it doesn't mean another could. That is like say you can drive a 18 wheeler like you can drive a boat. They both move you but one doesn't work in the other since it is not designed to do so.


I have got a new non standard answer from Bitmain.

Quote
The Antminer D3 has been designed and tested to mine DASH only. It can be used to mine other X11 coins as well but we cannot guarantee the performance or efficiency of the D3 miner when used to mine other X11 coins than DASH.

Best regards,
Joy
Bitmain
Always order products directly from our website: www.bitmain.com
"Solved" means we replied - we still work on your issue until it is resolved.


They just not garantee the performace, so they work on it.

Other x11 coins X11  aka

Dash (Darkcoin)

StartCoin

CannabisCoin

SmartCoin

ConspiracyCoin

Europecoin

GiveCoin

HashCoin

LimeXcoin

Logicoin

Muniti

Nyancoin

Quebecoin

XCurrency



The only benefit from this firmware is for the thread creator taking a fee. It does nothing you can't do already.

cant do ? so people are dumb , cause they dont share knowlege , cause it s impossible to find a tutorial -> how to set the fan down at : startup, switch pool , change setting in miner , etc ... and that the basic

we need that for other antminer , l3+, s9 etc.... i know a bit linux and i try to send cat in ssh with putty but this not result with usually cat editor , you just can see the text file
anyway blissz deserve fee for work and time, everyone are free dont agree and not using it.
sr. member
Activity: 800
Merit: 294
Created AutoTune to saved the planet! ~USA
Look if Baikal can do it I'm pretty sure the D3's can do it.... Watching this thread very closely.

Your an idiot. Baikal sells a Field Programmable Gate Array. Spartan FPGA or anything like that. You are an idiot. Just because one company can do it doesn't mean another could. That is like say you can drive a 18 wheeler like you can drive a boat. They both move you but one doesn't work in the other since it is not designed to do so.


I have got a new non standard answer from Bitmain.

Quote
The Antminer D3 has been designed and tested to mine DASH only. It can be used to mine other X11 coins as well but we cannot guarantee the performance or efficiency of the D3 miner when used to mine other X11 coins than DASH.

Best regards,
Joy
Bitmain
Always order products directly from our website: www.bitmain.com
"Solved" means we replied - we still work on your issue until it is resolved.


They just not garantee the performace, so they work on it.

Other x11 coins X11  aka

Dash (Darkcoin)

StartCoin

CannabisCoin

SmartCoin

ConspiracyCoin

Europecoin

GiveCoin

HashCoin

LimeXcoin

Logicoin

Muniti

Nyancoin

Quebecoin

XCurrency



The only benefit from this firmware is for the thread creator taking a fee. It does nothing you can't do already.
full member
Activity: 266
Merit: 102
Is it confirmed that the D3 can do other Algos? If so are the speed known?
nop
But theoretically it can though right? X11 is a combination of 11 algos chained together so it sees plausible. Other X11 Asics also do the algos contained in X11
we hope, it's the only way for make d3 profitable again, for now blissz did not talk about this opportunity
sr. member
Activity: 336
Merit: 250
Do the thing and you'll have the power.
Is it confirmed that the D3 can do other Algos? If so are the speed known?
nop
But theoretically it can though right? X11 is a combination of 11 algos chained together so it sees plausible. Other X11 Asics also do the algos contained in X11
full member
Activity: 348
Merit: 119
Is it confirmed that the D3 can do other Algos? If so are the speed known?
nop
sr. member
Activity: 336
Merit: 250
Do the thing and you'll have the power.
Is it confirmed that the D3 can do other Algos? If so are the speed known?
newbie
Activity: 105
Merit: 0


example, frequence set to 600 during 24h, temp intake between 10 to 16°C. No overtemp or other problem....

http://imageshack.com/a/img923/9172/lxiFI3.jpg
[/quote]

a lot of HW you have with this frequence  Cry
newbie
Activity: 27
Merit: 0
It was a test during 24h to check the possibility, I switch back on auto since.
one guys ask, I just showed and he made is own conclusion try or not...
newbie
Activity: 42
Merit: 0
Thanks for your work blissz on D3 firmware im not currently using it becouse i dont have to pay electricity  but i might be interested in OC it ,  can i get those 21 gh stable OC running 24/7 ? mine D3 is in cold ventilated space

I Hope we get to use D3 on single algos from x11 in your future Firmwares !!

example, frequence set to 600 during 24h, temp intake between 10 to 16°C. No overtemp or other problem....

http://imageshack.com/a/img923/9172/lxiFI3.jpg

Too many HW errors and too high temperatures a for a 24/7 use! I think 600 is too high for the intake temperatures (10°C.-16°C), and it might damage the miner sooner or later. Better lower it to keep the temperatures lower, max temperatures should be something between 70°C-73°C!
member
Activity: 287
Merit: 18
Thanks for your work blissz on D3 firmware im not currently using it becouse i dont have to pay electricity  but i might be interested in OC it ,  can i get those 21 gh stable OC running 24/7 ? mine D3 is in cold ventilated space

I Hope we get to use D3 on single algos from x11 in your future Firmwares !!

example, frequence set to 600 during 24h, temp intake between 10 to 16°C. No overtemp or other problem....




way.way to many HW errors for a 47min burn time...even with colder temps you'll see HW errors running that freq
newbie
Activity: 27
Merit: 0
On the wall if my wattmetre tell true an average arround 1000w (on 230V french electrical network at 50hz)
newbie
Activity: 13
Merit: 0
Thanks for your work blissz on D3 firmware im not currently using it becouse i dont have to pay electricity  but i might be interested in OC it ,  can i get those 21 gh stable OC running 24/7 ? mine D3 is in cold ventilated space

I Hope we get to use D3 on single algos from x11 in your future Firmwares !!

example, frequence set to 600 during 24h, temp intake between 10 to 16°C. No overtemp or other problem....

http://imageshack.com/a/img923/9172/lxiFI3.jpg

How much power are you pulling to reach that hash rate?
Pages:
Jump to: