Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 4. (Read 125923 times)

Bump 6 days Blissz

FYI, To answer my own question, I emailed bitmain, this is their response :

"Below are the normal temperature of chips - all in Centigrade,
D3: the temp(Chip) should be 35-80
If the PCB board temperature goes higher than 85 the miner will shut off automatically."

Is Blissz firmware v2 safe and stable?
Im getting lots of errors even on low settings so i was thinking to use autotune.
Thanks

many do not have easy access to 220: like sure they "could hook a miner into the dryer line, but unless they have more than a 30amp breaker on that then umm you can't dry clothes anymore. If you are covered in cheetos on the couch most of your life maybe that would be okay, but I'm pretty sure my wife would murder me for using the dryer's juice... with a miner.. upside the head.. like.. alot. The other side of it is laziness. (some who can and should just don't)- like I "could" climb up in the attic and run some lines and even use a bedroom for nothing but miners, but every time I think about it I'm like.. it's too hot up there (texas mind you) or it's too cold.. like now.  so basically 5 days out of the year I could stand to be up there.. but I probably won't think about it until after.. and then I'll be "it's too hot up there."

The D3 on a 220 line uses about 6amps and on a 110 about 8amps... you should be using a 220 line to get the most out of the unit. I am able to run 2 D3s and 1 L3 on a 20amp 220 line with no issues at all. The D3s are using about 925w of power at 16.6GH and the L3 using 810w and in total with all three units are using 11.3 amps in total. If you are popping a breaker with one D3 you have something else on the line.

On a side note with all these users that claim "electric is not an issue" because they get it included in their rent, I suggest you read your lease very closely. If the landlord sees that much of a spike in the electric bill, don't expect them to pay for it and if you do, don't expect to renew your lease. trying to run a device that would be the same as a second refrigerator and expecting the landlord to pay for it is a little naive. Normally the wording in a lease is "electric included within reason"... meaning if you over use the electric they can charge you for it. Or they could just change all of the breakers to your apt to 15amp and tie them into multiple lines so you will just keep popping them.

What site is banning cgminer 4.10?
don´t confuse with Firmware and mining software, the pool know only the mining software not what firmware you are running or what miner you use.

Honestly with 1200 potential output, the odds are that the psu would fry (read might even catch on fire) unless it has alot of over this and that protection built in, not gonna trip a breaker or even really fry the machine (unless burning wires melt the plastic 6 pin plugs) the boards though can handle more than the 13, there is just no significant gain (I know he didn't care about that my point is you would be pouring more electricity in and getting nothing out of it really. I mean going from 13  into the 20's and maxing out freq step by step until you get a bunch of errors you go from like 19ghs to 20.5 and who knows what the difference in watts are...  anyway he asked if it would trip the breaker, and no it won't unless there are other things running.. microwave or vaccum cleaner? miner on=instant trip.  13 to 15 though probably won't make a significant enough difference - not 100% on that since I neither have a kil-owat meter nor do I have a way to see the miner-side draw. - if that goes over 1200..well unless there is an overtemp trip in the psu things will get hot. - maybe news at 11 hot...(//edit for adding :over 1200 miner side - at the wall he has a limit of about 1600.. the 80% figure above comes from cheap contractors so maybe go with what homeboy said.. assume cheap assed bastards.. hehe I put in my own wiring fairly often and forget that other people don't go.. I'm putting a 10 amp breaker in.. use 15amp wire.. putting in a 20? use 30 amp wire etc... it's kind of a thing of mine. //)

Agreed 100%. Learning more about messing with electricity is key if you don't want to trash your gear.

That said, if you want to mess around and are more concerned about draw than damaging your D3, you CAN pick up a kill-a-watt and figure out your voltage/draw without math.

Ugg I'm not trying to be a jerk man but you are just really missing some big electrical concepts and I don't want you to fry your unit. Let's say it this way, the D3 run's at ~1100 Watts on 13/13/13 at 120v that's 9.2Amps (1100/120 = 9.16). That's your power draw. If you are on a 15 amp breaker switch you shouldn't put much more on it, typically 80% of the rated breaker is the max an electrician will tell you (15 * .8 = 12 amps max). Anything more than 12 Amps on a 15 amp breaker running CONSTANTLY might pop the breaker switch. Now that is out of the way changing to 13/18/13 will draw more current, I'm not sure how much but what I will say it applying that much voltage to the board has the risk of overheating or instantly electrocuting the ASIC chips on the hashboard. Thus if you don't understand these concepts I'd highly recommend you not to go past the 13 setting.

Ok so I am home from my trip to the USA and I finally can upgrade to this firmware.

except for the problem that my D3 is not showing up on my network so I can't upgrade over the network. D3 never worked  

so I am going to try to use a microSD to try and atleast get it running but I have no single god damn clue how the hell I am going to get this working.

got the beaglebone out but what do I use to flash a microSD and hopefully get it up and running.

i need a firmware with  like this blitz but needs to show like original bitman  because some site ban this 4.10.0
i cant find his older versions 11//26 or older

anyone can send please to adi57771@gmail com

K the apt wiring will not be an issue (make that should not.. depending on how cheap the contractors were hehe) and yes power switching psu's will have different inputs (or should) one for 110-ish is the one you want. That tells you what the psu will draw at max. if the 110*max amps on that line is less than 1600 you shouldn't pop the breaker. (lemme know btw since I might get one of these)     - breaker side will be fine.. but not sure how much the miner actually uses (so you don't fry the psu) but if other people are overclocking on the same type of power suplly without it being on 220 you will be fine.

Sometimes I wonder why people like this even bother replying... the whole point of me making a post here is not so I can brag about what I already "understand".... it's clearly because I don't and have a question to ask and would like an answer.





It's an apartment room with shared power to the room next to it I think? It was built within the last 5-8 years. I appreciate that you say it will only put out a max of 1200 watts but the psu input side is weird because it varies based on if you use a 220 volt house or less I think?

How can I know how many amps I'm currently pulling by having my voltage at 13/13/13 (bitmain default) ?

I think If I knew the bitmain default amps being used vs a standard amps maximum limit in a house that would be great.

Thanks for all the help I've gotten

Hi,

If I update the firmware of my D3, will it clear my assigned static ip on the device after the upgrade?

Thanks in advance

Side note: think you might want to go after ebang? They have a "dwangminer" that is clearly based on cgminer no source anywhere, backdoor into the miner, no way for the owner of the miner to change anything.. not even password on the web-ui - cause THERE is someone who might need to be slapped around with the gpl... or just slapped around.

you would have to write it from scratch not using ANY thing that was under the gpl. much wailing and gnashing of teeth.

K we need to know more stuff here .. many variables involved.. is it a new house? new apratment building? really old apartment building? warehouse?  is ANYTHING else plugged in on that circuit?  even a tv that is off draws power now-a-days. the bitmain firmware for the 19ghs batches claim 1500+ (can't remember the total number) at the wall. So that is under what your circuit can do. not by much but you should be good unless you have really old wiring. or a weak breaker (happens more than you would think) BUT your psu will only put out a max of 1200 so it might fry the psu trying to put out enough juice..(and still not pop the breaker) but I do not know the miner-side power draw at those settings.. so can't tell you for sure.  each psu/hashingboard/wiring setup/breaker is all different.. this is all rule of thumb kinda stuff. *IF* someone else out there is running 20/20/20 on the same psu as you have then yeah it should be fine. or if someone knows more about the miner-side power draw vs at the wall ??
basically if you can look it up maybe at bitmain. so long as your psu can handle it .. it should not pop the breaker *IF* there is nothing else on the circuit. (on your psu look at the input side.. at 110 and max amps if that number is less than 1600 it shouldn't pop the breaker)

i bet he is using the software aswell. and bites the hand which is feeding him.
in my opinion its even better we can mine with less power usage from the ecological point of view.

is it possible to implement another miner, which is not under GPL?

"most" dryers in the us are on a 240v 30 amp circuit.  just an fyi before someone tries to draw 50.

Thanks for the tl;dr version   Got coffee in me now too btw I knew I had a good chance to be wrong on the letter of the "law" there which is why all the disclaimer bit.  I assume the part that fits here is the All code linked with GPL 3.0 source code must be disclosed under a GPL 3.0 compatible license bit? and yeah that is much clearer.
I disagree with the "you fuckers" you is pretty general there - and what few this is pretty publicly available, though I get what you mean by if all d3's come out increased in hashrate then same situation as before.. but lower hashrate and increased profit (by way of using less electricity) does A) no more harm to crypto than bitmain releasing too many of a machine did.. in fact it lessens the impact. and B) makes it where the people who bought them can get more out of them.  side note: if bitmain released very few of a machine it would only benefit the few anyway.. just sayin' - on to supporting crypto altruistically.. is that really what you are doing? the coins are economy driven, so.. there is like money involved in there somewhere. If you want to support crypto AND make a buck what is wrong with that? again just sayin'  Did you install the firmware? Do you mine for free? Do you give all your coins to charity? Would you expect someone in a different field to be as altruistic? - hey that's cool if you do.. but most people won't EVER be like that. Not that they aren't good people and want the best for others (like blissz could have made the firmware for himself and just never released it to anyone but -I do not know this for sure- I'm betting he thought hey let's share this to help people recoup from the plummet) anyway forgot what I was saying. *rofl* maybe still not enough coffee.