I read information in PDF file, it looks like this project can be real. I hope so, ha-ha
Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 61. (Read 125911 times)
I read information in PDF file, it looks like this project can be real. I hope so, ha-ha
His firmware is based on Bitmain's latest firmware, he did this many days ago.
Hmm, strange, I just updated new blissz firmware, comsuption is reduced, but I had already 1 dead board. Last 5 days after I installed last Bitmain firmware I had 0 hashboards dead until now.
Hi, Blissz!
Thx for your hard work!
About v1.02 (beta)
I have one of the D3's that has not shows one of the hash boards.
I tried to launch it via standard Bitmain's firmware, but result was negative.
Then I installed the firmware v1.01 - the missed card appears 50/50.
Finally, I tried with v1.02 (beta), and the result is amazing - all three boards are visible and now all boards show 0 HW.
Great! Now I want to restart cgminer some times to make sure that everything works stable.
P.S.: after restart, all works fine, all boards are visible and 0 HW for each one! Thanks a lot!
Thx for your hard work!
About v1.02 (beta)
I have one of the D3's that has not shows one of the hash boards.
I tried to launch it via standard Bitmain's firmware, but result was negative.
Then I installed the firmware v1.01 - the missed card appears 50/50.
Finally, I tried with v1.02 (beta), and the result is amazing - all three boards are visible and now all boards show 0 HW.
Great! Now I want to restart cgminer some times to make sure that everything works stable.
P.S.: after restart, all works fine, all boards are visible and 0 HW for each one! Thanks a lot!
His firmware is based on Bitmain's latest firmware, he did this many days ago.
Thank you for info, so I can set "lowest" voltage options, and than I should see how far I can go with clock, before I start do get HW errors? Lowest voltage can works on some devices on 450 mhz clock?
Can I damage board if miner works on very low voltage on some higher clock than 400mhz, but without errors?
Is it "dead board" problem fixed, no more dead boards after some time?
If still exist this problem blissz should use this Bitmain last FW:
https://shop.bitmain.com/support.htm?pid=00720170915192851224mJ36J1ap066E
Works fine for now on testing device, 425mhz, 800w, 16ghs
Can I damage board if miner works on very low voltage on some higher clock than 400mhz, but without errors?
Is it "dead board" problem fixed, no more dead boards after some time?
If still exist this problem blissz should use this Bitmain last FW:
https://shop.bitmain.com/support.htm?pid=00720170915192851224mJ36J1ap066E
Works fine for now on testing device, 425mhz, 800w, 16ghs
"Lowest" voltage is value 1, right? I tried lowest voltage and 412mhz clock and works. Can lowest value can work with higher clock, for example 450mhz?
Why blissz wrote lowest voltage on 400mhs, when clock can bi higher?
Why blissz wrote lowest voltage on 400mhs, when clock can bi higher?
Its just a recomended starting point if you want to run silent and low watts.
You can move it where ever you want. These boards are so different that you can't say this one setting is for everyone.
Also if still happens that some board go dead. Blissz should work on last Bitmain FW, I got this FW from Bitmain 7 days ago, and after that all miners works perfect, no more dead boards after some time.
Link for Bitmain lastest bios:
https://shop.bitmain.com/support.htm?pid=00720170915192851224mJ36J1ap066E
Link for Bitmain lastest bios:
https://shop.bitmain.com/support.htm?pid=00720170915192851224mJ36J1ap066E
"Lowest" voltage is value 1, right? I tried lowest voltage and 412mhz clock and works. Can lowest value can work with higher clock, for example 450mhz?
Why blissz wrote lowest voltage on 400mhs, when clock can bi higher?
Why blissz wrote lowest voltage on 400mhs, when clock can bi higher?
Hi!
I installed Blissz firmware in my d3's and I made a mistake copying the cgminer archive from /usr/bin from one of the d3 to an l3+ I have too.
Of course it started up in the l3+ with the --scrypt param but it didn't mine anything.
I flashed my l3+ to stock again but now it doesn't recognize any of the chains on my l3+!
I'm begining to enter in panic! Could somebody help me with that? What should I do?
I think is because some additional files created or some script running in parallel with cgminer. I don't know really but that file is the only I changed "trying to not touch the filesystem" :S.
By the way, Is there any plan to make a firmware for l3's? It would be nice! on d3's are running amazing.
Thanks in advance.
I installed Blissz firmware in my d3's and I made a mistake copying the cgminer archive from /usr/bin from one of the d3 to an l3+ I have too.
Of course it started up in the l3+ with the --scrypt param but it didn't mine anything.
I flashed my l3+ to stock again but now it doesn't recognize any of the chains on my l3+!
I'm begining to enter in panic! Could somebody help me with that? What should I do?
I think is because some additional files created or some script running in parallel with cgminer. I don't know really but that file is the only I changed "trying to not touch the filesystem" :S.
By the way, Is there any plan to make a firmware for l3's? It would be nice! on d3's are running amazing.
Thanks in advance.
BLISSZ .....
Can you please help us....
There are many more who did this....;(
Please give us a hand...
Bitmain sent me a replacement control board for free. Even thought I said it was my mistake and put the wrong firmware on it. From opening of ticket to delivery it was 7 days to the UK. Not bad shame the rest of the business couldn't be that smooth
Thank you for your response. I'm going to open a ticket with bitmain then.
Regards!
Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?
Cheers W_M
Cheers W_M
around 1250W
Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w
wich settings do you use for the 20GH/s at 1100W?
@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
great job blissz!
20GH at 1100 watts is impressive is this with factory firmware ?
No, with Blissz firmware of course
These are my settings but each miner (and board) is different, you have to tweak until you see good temperature and HW errors
Right there in the pic (I'm having some issues linking pics here, but my original post has the links). Temps around 70C, fans go between 3500 and 4000, but this is in a quite cool room (about 50F). Once I move it to my garage where I have more challenges cooling things down I may need to dial this back a little.
EDIT: Oh, and I have the fan in "AUTO performance"
Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?
Cheers W_M
Cheers W_M
around 1250W
Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w
wich settings do you use for the 20GH/s at 1100W?
@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
great job blissz!
20GH at 1100 watts is impressive is this with factory firmware ?
No, with Blissz firmware of course
These are my settings but each miner (and board) is different, you have to tweak until you see good temperature and HW errorshttps://imgur.com/JiZz4to.jpg
https://imgur.com/y8GctAY.jpg
Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?
Cheers W_M
Cheers W_M
around 1250W
Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w
wich settings do you use for the 20GH/s at 1100W?
@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
great job blissz!
20GH at 1100 watts is impressive is this with factory firmware ?
No, with Blissz firmware of course
These are my settings but each miner (and board) is different, you have to tweak until you see good temperature and HW errors
What is the maximum hashrate you can achieve with stability on a 19.3 model? My aim is for maximum hashrate and not efficiency, but don't want to risk burning a board since its working full time. Temps are stable now at 70c with 19.3.
Just want to know if its worth putting this firmware and overclock, as from what i see is more foccused in efficiency
Thanks
Just want to know if its worth putting this firmware and overclock, as from what i see is more foccused in efficiency
Thanks
I've been getting about 22-23g but Nicehash sometimes reports up to 28g
The Firmware is goog for both, efficiency or max Hashrate, because you can get out the max from every hashboard and you must not stop because one board get to hot, take only care that your chips not get to hot.
Maybe I have set diff level too high, I have been trying d=32000.
Where I can change this value?
Hi, in the password field you just add d=40 for a diff of 40.
So mine is c=DASH,d=80 in the password field.
This is for zpool.ca, other pools may do it in a different way.
Thanks, but I use antpool.
Why doesn't Blissz make a firmware for the L3+?
he doesn't have an L3+. Send him one and I'm sure he'll bang off some new firmware.
Why doesn't Blissz make a firmware for the L3+?
I'm sure he will but he is busy perfecting the D3 for now
What is best miner hashing/setup for 950w power consumption? Can I get 17-18ghs on 950w?
Hi!
I installed Blissz firmware in my d3's and I made a mistake copying the cgminer archive from /usr/bin from one of the d3 to an l3+ I have too.
Of course it started up in the l3+ with the --scrypt param but it didn't mine anything.
I flashed my l3+ to stock again but now it doesn't recognize any of the chains on my l3+!
I'm begining to enter in panic! Could somebody help me with that? What should I do?
I think is because some additional files created or some script running in parallel with cgminer. I don't know really but that file is the only I changed "trying to not touch the filesystem" :S.
By the way, Is there any plan to make a firmware for l3's? It would be nice! on d3's are running amazing.
Thanks in advance.
I installed Blissz firmware in my d3's and I made a mistake copying the cgminer archive from /usr/bin from one of the d3 to an l3+ I have too.
Of course it started up in the l3+ with the --scrypt param but it didn't mine anything.
I flashed my l3+ to stock again but now it doesn't recognize any of the chains on my l3+!
I'm begining to enter in panic! Could somebody help me with that? What should I do?
I think is because some additional files created or some script running in parallel with cgminer. I don't know really but that file is the only I changed "trying to not touch the filesystem" :S.
By the way, Is there any plan to make a firmware for l3's? It would be nice! on d3's are running amazing.
Thanks in advance.
BLISSZ .....
Can you please help us....
There are many more who did this....;(
Please give us a hand...
Bitmain sent me a replacement control board for free. Even thought I said it was my mistake and put the wrong firmware on it. From opening of ticket to delivery it was 7 days to the UK. Not bad shame the rest of the business couldn't be that smooth
control board will not change nothing , i try with an other one , hashboards are fail , i ever told taht
@Blissz please answer to mp
What is the maximum hashrate you can achieve with stability on a 19.3 model? My aim is for maximum hashrate and not efficiency, but don't want to risk burning a board since its working full time. Temps are stable now at 70c with 19.3.
Just want to know if its worth putting this firmware and overclock, as from what i see is more foccused in efficiency
Thanks
Just want to know if its worth putting this firmware and overclock, as from what i see is more foccused in efficiency
Thanks
I've been getting about 22-23g but Nicehash sometimes reports up to 28g
Jump to: