blissz,
FYI, I had the 1 chain high/low temp issue on my miner that had the stock 11/2 firmware, updated to stock 11/20 and it fixed the issue for several days. Now I updated to blissz 11/29 and the issue is back. I'm going to try the release before 11/29 and see if it has the issue also.
Also, it would be nice if you could leave the links to the last several versions in the first post if possible. thanks
Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 60. (Read 125911 times)
what the over clock for d3 and l3
is there is the same firmware for l3
is there is the same firmware for l3
tried this software
chain 1 shows a low pcb temp but temps on chip
never go below 100 unless i really reduce the freqency all the way below 350
fans are set to auth performace and my room is very cool
all the other chain temps are low even at 500+ freqncy and 8 - 9 voltage
chain 1 shows a low pcb temp but temps on chip
never go below 100 unless i really reduce the freqency all the way below 350
fans are set to auth performace and my room is very cool
all the other chain temps are low even at 500+ freqncy and 8 - 9 voltage
Great software Blissz, very useful for me I keep my miners in house in the cavity under the stairs, this software allows me to goto silent mode at night not disturbing the kids and performance during day to balance my overall daily hash rate at same time as save electric, great work
hello.
i'm rnning blissz firmware on a D3-504.
any suggstion or experience for voltage, trying to keep highest hashrate?
i want to keep mining DASH.
tnx
i'm rnning blissz firmware on a D3-504.
any suggstion or experience for voltage, trying to keep highest hashrate?
i want to keep mining DASH.
tnx
Hi Blissz,
Did you fix it? The bug continues. Although Pool 1 has survived, the machine continues to run on your pool forever.
Did you fix it? The bug continues. Although Pool 1 has survived, the machine continues to run on your pool forever.
It's fixed in the beta firmware, a few pages back, but you can also wait on the next stable firmware (probably today / tommmorow).
Hi Blissz,
Did you fix it? The bug continues. Although Pool 1 has survived, the machine continues to run on your pool forever.
Did you fix it? The bug continues. Although Pool 1 has survived, the machine continues to run on your pool forever.
Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?
Cheers W_M
Cheers W_M
around 1250W
Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w
wich settings do you use for the 20GH/s at 1100W?
@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
great job blissz!
20GH at 1100 watts is impressive is this with factory firmware ?
https://i.imgur.com/JiZz4to.jpg
https://i.imgur.com/y8GctAY.jpg
I can't see this picture,how to set 20g for this firmware?
This is my best with the window open on a mountain at night, (Temp=5C) w/o any H/w, I am crossing my fingers I do not have to restart for awhile. I stayed with 29/11: Blissz, tell me when to switch please kind sir.
Freq on typically coolest chain (for me chain 2) 550 freq @ 11V - 6834.67
Hottest chain 531 and 12 V- 6722.86
Middle temp chain 544 and 11 V -8889.6
M
Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?
Cheers W_M
Cheers W_M
around 1250W
Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w
wich settings do you use for the 20GH/s at 1100W?
@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
great job blissz!
20GH at 1100 watts is impressive is this with factory firmware ?
No, with Blissz firmware of course
These are my settings but each miner (and board) is different, you have to tweak until you see good temperature and HW errors
I can't see this picture,how to set 20g for this firmware?
Just click the link to open the pic. My settings won't work for you, each miner (and each card) are different, you have to tune it yourself. Also your miner may not get there, or can do better, again, all of them are different.
Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?
Cheers W_M
Cheers W_M
around 1250W
Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w
wich settings do you use for the 20GH/s at 1100W?
@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
great job blissz!
20GH at 1100 watts is impressive is this with factory firmware ?
No, with Blissz firmware of course
These are my settings but each miner (and board) is different, you have to tweak until you see good temperature and HW errorshttps://i.imgur.com/JiZz4to.jpg
https://i.imgur.com/y8GctAY.jpg
I can't see this picture,how to set 20g for this firmware?
Not sure people keep bring up this site, it has been stated by multiple people on this thread that the website is very likely a scam.
but now they are hiring ... I'll take "Job 2" LOL
Hi, Blissz!
Thx for your hard work!
About v1.02 (beta)
I have one of the D3's that has not shows one of the hash boards.
I tried to launch it via standard Bitmain's firmware, but result was negative.
Then I installed the firmware v1.01 - the missed card appears 50/50.
Finally, I tried with v1.02 (beta), and the result is amazing - all three boards are visible and now all boards show 0 HW.
Great! Now I want to restart cgminer some times to make sure that everything works stable.
P.S.: after restart, all works fine, all boards are visible and 0 HW for each one! Thanks a lot!
Thx for your hard work!
About v1.02 (beta)
I have one of the D3's that has not shows one of the hash boards.
I tried to launch it via standard Bitmain's firmware, but result was negative.
Then I installed the firmware v1.01 - the missed card appears 50/50.
Finally, I tried with v1.02 (beta), and the result is amazing - all three boards are visible and now all boards show 0 HW.
Great! Now I want to restart cgminer some times to make sure that everything works stable.
P.S.: after restart, all works fine, all boards are visible and 0 HW for each one! Thanks a lot!
Thank you for your post,t's good to hear this helps for startup stability as that was the main goal for this version. Some final tweaks before the next stable version....
Ok I agree with you smart guys.
it is a scam obviously
everyone can relax . I dont post anything about them anymore.
I am only a D3 owner , thats all.
it is a scam obviously
everyone can relax . I dont post anything about them anymore.
I am only a D3 owner , thats all.
Yes, and he, D3 antminer, already posted that many many times in many topics. I doubt him.
Maybe it's a bot?
Yes, and he, D3 antminer, already posted that many many times in many topics. I doubt him.
its a SCAM
already wrote many times
"We need your financial support. As you already know, we are a non-profit team, but some team members without whom the project will not be done , will not work for thanks. Likewise, we need to get more D3's for ASIC designers, developers and for an Alpha test with reliable statistics. At the moment the project is funded by us. That's why we need your donations now, so the project can go further."
i cant stop laught of loud man
i cant stop laught of loud man
that's just too good 
"We need your financial support. As you already know, we are a non-profit team, but some team members without whom the project will not be done , will not work for thanks. Likewise, we need to get more D3's for ASIC designers, developers and for an Alpha test with reliable statistics. At the moment the project is funded by us. That's why we need your donations now, so the project can go further."
i cant stop laught of loud man
i cant stop laught of loud man
is there any one who can evaluate this document ,if it is real thing or bullshit
https://docs.wixstatic.com/ugd/a1e324_8f0fe54926d34614ac3cc734dc66b2b8.pdf
https://docs.wixstatic.com/ugd/a1e324_8f0fe54926d34614ac3cc734dc66b2b8.pdf
Not sure people keep bring up this site, it has been stated by multiple people on this thread that the website is very likely a scam.
Jump to: