reuploading...
Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 81. (Read 125911 times)
ya i found this https://www.3m.com/3M/en_US/novec-us/applications/immersion-cooling/
any one know how to get that stuff or where to get , thanks may142012 for the word to search for
any one know how to get that stuff or where to get , thanks may142012 for the word to search for
is there not some hi tec spray or liquid you can make pc boards water proof and then run boards half way submerged in water ?
"Immersion Cooling", that what they use for their gaming PC, don't know about Asic boards though.
is there not some hi tec spray or liquid you can make pc boards water proof and then run boards half way submerged in water ?
Some more feature requests...
- Perhaps trivial, display Temps in both C and F on the admin interface.
- Re: ability to swap pools around easily... perhaps just a UI change to the config form... add ability to add pool rows, but also include a tickbox to enable/disable them, would at least save the copy/paste shuffle step.
- I have some IO/GPIO ideas too, but I need to take a closer look at the beagle-board black that bitmain is using. (Like the ability to add an ambient [intake] breakout temp sensor, and trigger shutdowns or profile changes that way too).
Fan 0 Setting...
Is my understanding correct that at this setting the firmware cares zero f*cks about what the sense cable says. You mentioned this enables 3rd party fan mods... so is it still gonna spew 12v on two wires, but do nothing with the control and sense? Or are you implying powering the 3rd party fans directly off the supply?
Cheers!
- Perhaps trivial, display Temps in both C and F on the admin interface.
- Re: ability to swap pools around easily... perhaps just a UI change to the config form... add ability to add pool rows, but also include a tickbox to enable/disable them, would at least save the copy/paste shuffle step.
- I have some IO/GPIO ideas too, but I need to take a closer look at the beagle-board black that bitmain is using. (Like the ability to add an ambient [intake] breakout temp sensor, and trigger shutdowns or profile changes that way too).
Fan 0 Setting...
Is my understanding correct that at this setting the firmware cares zero f*cks about what the sense cable says. You mentioned this enables 3rd party fan mods... so is it still gonna spew 12v on two wires, but do nothing with the control and sense? Or are you implying powering the 3rd party fans directly off the supply?
Cheers!
Thanks for the suggestions! You can already remove the fans if you want: it will still provide 12v / PWM and read the RPM, but it continues mining as long as you keep it cool.
ok let me try it , like proper
bitcointalk needs to fix the can't reply more than once every 360 seconds. Kills the conversation.
Try lowering the frequency for that one board. I just go incrementally down. If you are using the modified firmware I would set it to a default voltage find a frequency that is stable then walk the voltage backwards until you find errors.
mine showing missing "0" and when hashing starts turns to "x"...wierd dunno if firmware related(not blissz) or actual hardware failure ie: chain scission of chips" issue
Try lowering the frequency for that one board. I just go incrementally down. If you are using the modified firmware I would set it to a default voltage find a frequency that is stable then walk the voltage backwards until you find errors.
Some more feature requests...
- Perhaps trivial, display Temps in both C and F on the admin interface.
- Re: ability to swap pools around easily... perhaps just a UI change to the config form... add ability to add pool rows, but also include a tickbox to enable/disable them, would at least save the copy/paste shuffle step.
- I have some IO/GPIO ideas too, but I need to take a closer look at the beagle-board black that bitmain is using. (Like the ability to add an ambient [intake] breakout temp sensor, and trigger shutdowns or profile changes that way too).
Fan 0 Setting...
Is my understanding correct that at this setting the firmware cares zero f*cks about what the sense cable says. You mentioned this enables 3rd party fan mods... so is it still gonna spew 12v on two wires, but do nothing with the control and sense? Or are you implying powering the 3rd party fans directly off the supply?
Cheers!
- Perhaps trivial, display Temps in both C and F on the admin interface.
- Re: ability to swap pools around easily... perhaps just a UI change to the config form... add ability to add pool rows, but also include a tickbox to enable/disable them, would at least save the copy/paste shuffle step.
- I have some IO/GPIO ideas too, but I need to take a closer look at the beagle-board black that bitmain is using. (Like the ability to add an ambient [intake] breakout temp sensor, and trigger shutdowns or profile changes that way too).
Fan 0 Setting...
Is my understanding correct that at this setting the firmware cares zero f*cks about what the sense cable says. You mentioned this enables 3rd party fan mods... so is it still gonna spew 12v on two wires, but do nothing with the control and sense? Or are you implying powering the 3rd party fans directly off the supply?
Cheers!
mine showing missing "0" and when hashing starts turns to "x"...wierd dunno if firmware related(not blissz) or actual hardware failure ie: chain scission of chips" issue
Have the same issue... but even with the original firmware.
Yes. I removed one board. Waiting on Bitmain to respond. My machine is under warranty.
The two board unit is running at 10,700 at 560W.
475 and 437 both at lowest volt setting.
default fan
The two board unit is running at 10,700 at 560W.
475 and 437 both at lowest volt setting.
default fan
Did the defective board show any signs of "xxx" or missing any "ooo"?
It was a long process that led to this.
At first Machine 1. that i had to remove a board from was way more stable than Machine 2 (which is now runnning perfectly).
Turned it off for the night next day started getting xxx then would stop mining all together and machine 1 would stop minning all togther.
If I set the frequency low enough on the one board. 250-300 it will show all 000 however it wont mine. Just the two other boards will. But its using power. because the chips are being fed (which is biggest reason for removal.)
I can get it to mine at default voltage at 300 for a short period then craps out the entire system. Really disappointing.
mine showing missing "0" and when hashing starts turns to "x"...wierd dunno if firmware related(not blissz) or actual hardware failure ie: chain scission of chips" issue
Yes. I removed one board. Waiting on Bitmain to respond. My machine is under warranty.
The two board unit is running at 10,700 at 560W.
475 and 437 both at lowest volt setting.
default fan
The two board unit is running at 10,700 at 560W.
475 and 437 both at lowest volt setting.
default fan
Did the defective board show any signs of "xxx" or missing any "ooo"?
My one Board showed missing 2x oo and now it has xx next to them, any ideas?
Yes. I removed one board. Waiting on Bitmain to respond. My machine is under warranty.
The two board unit is running at 10,700 at 560W.
475 and 437 both at lowest volt setting.
default fan
The two board unit is running at 10,700 at 560W.
475 and 437 both at lowest volt setting.
default fan
Did the defective board show any signs of "xxx" or missing any "ooo"?
Ok, so how can i make my antminer go back to its origin format?
Just take the firmware file from bitmain, flash it and your miner is as it was out of the box
Yes. I removed one board. Waiting on Bitmain to respond. My machine is under warranty.
The two board unit is running at 10,700 at 560W.
475 and 437 both at lowest volt setting.
default fan
The two board unit is running at 10,700 at 560W.
475 and 437 both at lowest volt setting.
default fan
Ok, so how can i make my antminer go back to its origin format?
I have some problem with setting frequency for single hashboard.....
https://imgur.com/gq64Rft
https://imgur.com/RxI9wFd
I think that the chinese worker who has mounted my three D3 First batch don't like the connector #1 of my board.. he connected board 2,3,4....https://imgur.com/gq64Rft
https://imgur.com/RxI9wFd
i think that this is the problem... tomorrow i turn off the miner and i change the position of connector.......
hey
i also have problems with frequency settings ..
no changes will aply it is stuck to 419M
doesnt care what i choose and click on save/&apply its again at 419M
i also have problems with frequency settings ..
no changes will aply it is stuck to 419M
doesnt care what i choose and click on save/&apply its again at 419M
Hi Blissz,
There are two URL (dash.supernova.ca:9995)-->devFeeMiner.2 and (dash-eu.coinmine.pl:6099) --> devFeeMiner.1
? !!!! that are running now and i have no idea what they are for as I did not write them. Also, when i go to the settings and try to remove them i can't find them. Is it something you added or you're aware of? Please take a look they are shown in the picture. It would be great if you can tell me what they are. I think there is something wrong.
There are two URL (dash.supernova.ca:9995)-->devFeeMiner.2 and (dash-eu.coinmine.pl:6099) --> devFeeMiner.1
? !!!! that are running now and i have no idea what they are for as I did not write them. Also, when i go to the settings and try to remove them i can't find them. Is it something you added or you're aware of? Please take a look they are shown in the picture. It would be great if you can tell me what they are. I think there is something wrong.You can't remove them. There are used for devfee, as specified. The way Blissz gets his bonus
Hi Blissz,
There are two URL (dash.supernova.ca:9995)-->devFeeMiner.2 and (dash-eu.coinmine.pl:6099) --> devFeeMiner.1? !!!! that are running now and i have no idea what they are for as I did not write them. Also, when i go to the settings and try to remove them i can't find them. Is it something you added or you're aware of? Please take a look they are shown in the picture. It would be great if you can tell me what they are. I think there is something wrong.
Don't worry, that's your donation to Blissz for his hard work. It's working normal. You can read more about it at the beginning of the thread. There are two URL (dash.supernova.ca:9995)-->devFeeMiner.2 and (dash-eu.coinmine.pl:6099) --> devFeeMiner.1
? !!!! that are running now and i have no idea what they are for as I did not write them. Also, when i go to the settings and try to remove them i can't find them. Is it something you added or you're aware of? Please take a look they are shown in the picture. It would be great if you can tell me what they are. I think there is something wrong.Jump to: