Topic: ANTMINER S3+ Discussion and Support Thread - page 3. (Read 710231 times)
Can you show a picture from your "Miner Configuration" tab?
check to make sure there is no blank spaces at the end of the pool url.
no space at the end !
i have this screen !
What it means ? that it is broken ?
check to make sure there is no blank spaces at the end of the pool url.
i have this screen !
What it means ? that it is broken ?
This status screen says that nothing works because there is no system load. Have you already done your initial setup Network/poolsettings?
https://s31.postimg.org/4x0w5hzuj/antminer.jpg
i have this screen !
What it means ? that it is broken ?
i have this screen !
What it means ? that it is broken ?
ok when I try to change my default gate way to 192.168.1.1 I get an error message that says warning the default gateway is not on the same network segment (subnet) that is defined by two ip address do you want to continue then when I hit continue I lose my internet connection with my router. My desktop Is wireless connected to my router and my antminer is connected to my router. my normal routers default gateway is a high number. Is there a possibility that I need to get a new router Please somebody help me out.
Are you using the right subnet mask? I noticed in your earlier post you said the following:Status Name IP Radmin Http Https Ftp Rdp Shared folders NetBIOS group Manufacturer MAC address User Comments
Ok 192.168.1.xx 192.168.1.xx Shenzhen Ogemray Technology Co., Ltd. Update after I set it up the old owner had it set to a specific address so when I changed from static to dhcp it went back to the address he had it set at. I checked the unit as it is hooked up to my router and is working great. Ok whats the next step to get my router to tie to my computer. When I changed from static to dhcp it inactivated the 192.168.1.99 and activated the top number I know thats it now how to access it. thats listed as inactive under my ip scanner. Ok whats the next step.lol Thank you so much for any help as I am a disabled veteran. my pc is a custom built Intel I7 4th generation computer running windows 10. this one is Dead 192.168.1.99 192.168.1.99 Paragon Technologies Inc.
You said, "192.168.1.xx 192.168.1.xx" and "192.168.1.99 192.168.1.99" which leads me to believe that you are typing the IP address twice, once in the IP address and once in the subnet mask.Ok 192.168.1.xx 192.168.1.xx Shenzhen Ogemray Technology Co., Ltd. Update after I set it up the old owner had it set to a specific address so when I changed from static to dhcp it went back to the address he had it set at. I checked the unit as it is hooked up to my router and is working great. Ok whats the next step to get my router to tie to my computer. When I changed from static to dhcp it inactivated the 192.168.1.99 and activated the top number I know thats it now how to access it. thats listed as inactive under my ip scanner. Ok whats the next step.lol Thank you so much for any help as I am a disabled veteran. my pc is a custom built Intel I7 4th generation computer running windows 10. this one is Dead 192.168.1.99 192.168.1.99 Paragon Technologies Inc.
Based on the following statement:
Ok guys here I go again I am able to log on to the interface and set up my miner but once I do nothing happens? here is the info my computer won't let me take screen shots so I am copy pasting
antMiner
Model S3
Firmware Version Fri Jan 9 20:41:34 CST 2015
Kernel Version 3.10.12
Local Time Mon Dec 2 11:42:52 2013
Uptime 0h 15m 6s
Load Average 0.00, 0.04, 0.09
Memory
Total Available
48848 kB / 61568 kB (79%)
Free
38852 kB / 61568 kB (63%)
Cached
7772 kB / 61568 kB (12%)
Buffered
2224 kB / 61568 kB (3%)
Network
IPv4 WAN Status
eth1 Type: static
Address: 192.168.1.x
Netmask: 255.255.255.0
Gateway: 192.168.1.1
DNS 1: 192.168.1.1
Connected: 0h 9m 35s
Active Connections
85 / 16384 (0%)
DHCP Leases
Hostname IPv4-Address
the above is off of the front screen of my miner status
You should be using the subnet mask 255.255.255.0. In other words, I was expecting you to write "192.168.1.xx 255.255.255.0" or "192.168.1.99 255.255.255.0" in that first quote I gave. antMiner
Model S3
Firmware Version Fri Jan 9 20:41:34 CST 2015
Kernel Version 3.10.12
Local Time Mon Dec 2 11:42:52 2013
Uptime 0h 15m 6s
Load Average 0.00, 0.04, 0.09
Memory
Total Available
48848 kB / 61568 kB (79%)
Free
38852 kB / 61568 kB (63%)
Cached
7772 kB / 61568 kB (12%)
Buffered
2224 kB / 61568 kB (3%)
Network
IPv4 WAN Status
eth1 Type: static
Address: 192.168.1.x
Netmask: 255.255.255.0
Gateway: 192.168.1.1
DNS 1: 192.168.1.1
Connected: 0h 9m 35s
Active Connections
85 / 16384 (0%)
DHCP Leases
Hostname IPv4-Address
the above is off of the front screen of my miner status
yes there is a mac address assigned to it I did an ip search and everything is connected and working. Now I just have to figure out how to get my miner going.
Is the MAC address showing up? My S7 blanked it out when I switched from DHCP to Static for some reason. I did a reset and reconnected thru the default address and was able to successfully change things the second time around.
Ok guys here I go again I am able to log on to the interface and set up my miner but once I do nothing happens? here is the info my computer won't let me take screen shots so I am copy pasting
antMiner
Model S3
Firmware Version Fri Jan 9 20:41:34 CST 2015
Kernel Version 3.10.12
Local Time Mon Dec 2 11:42:52 2013
Uptime 0h 15m 6s
Load Average 0.00, 0.04, 0.09
Memory
Total Available
48848 kB / 61568 kB (79%)
Free
38852 kB / 61568 kB (63%)
Cached
7772 kB / 61568 kB (12%)
Buffered
2224 kB / 61568 kB (3%)
Network
IPv4 WAN Status
eth1 Type: static
Address: 192.168.1.x
Netmask: 255.255.255.0
Gateway: 192.168.1.1
DNS 1: 192.168.1.1
Connected: 0h 9m 35s
Active Connections
85 / 16384 (0%)
DHCP Leases
Hostname IPv4-Address
the above is off of the front screen of my miner status
antMiner
Model S3
Firmware Version Fri Jan 9 20:41:34 CST 2015
Kernel Version 3.10.12
Local Time Mon Dec 2 11:42:52 2013
Uptime 0h 15m 6s
Load Average 0.00, 0.04, 0.09
Memory
Total Available
48848 kB / 61568 kB (79%)
Free
38852 kB / 61568 kB (63%)
Cached
7772 kB / 61568 kB (12%)
Buffered
2224 kB / 61568 kB (3%)
Network
IPv4 WAN Status
eth1 Type: static
Address: 192.168.1.x
Netmask: 255.255.255.0
Gateway: 192.168.1.1
DNS 1: 192.168.1.1
Connected: 0h 9m 35s
Active Connections
85 / 16384 (0%)
DHCP Leases
Hostname IPv4-Address
the above is off of the front screen of my miner status
follow up three it must have been windows 10 because when I went to connect the miner to the modem it said that there was an update to fix the issue. Windows restarted and connected tom my miner and the internet. which before I could only do one or the other. Should I keep my miner on static or switch it to dhcp. I also was able to change my miner address I found out at my security camera shared the same ip address as my miner how crazy is that.
I like static as I can alway's find it at same IP. With multiple miners it becomes nice to have. I would either 1 leave alone with DHCP looking at your issues, I hate for you to go though trying to set networking again. Or 2 take a screenshot of what you trying to use as settings with static and show us on here so we can see if something is wrong.
If you have security camera and S3 figihting for IP it would cause problems. But again reading last 3 posts if it's working might think about leaving it for now.
follow up three it must have been windows 10 because when I went to connect the miner to the modem it said that there was an update to fix the issue. Windows restarted and connected tom my miner and the internet. which before I could only do one or the other. Should I keep my miner on static or switch it to dhcp. I also was able to change my miner address I found out at my security camera shared the same ip address as my miner how crazy is that.
update 2 I ran my ehternet cable from my computer and reset it again. I was able to access the interface and I changed the address should I have changed it from static to dhcp.
Status Name IP Radmin Http Https Ftp Rdp Shared folders NetBIOS group Manufacturer MAC address User Comments
Ok 192.168.1.xx 192.168.1.xx Shenzhen Ogemray Technology Co., Ltd. Update after I set it up the old owner had it set to a specific address so when I changed from static to dhcp it went back to the address he had it set at. I checked the unit as it is hooked up to my router and is working great. Ok whats the next step to get my router to tie to my computer. When I changed from static to dhcp it inactivated the 192.168.1.99 and activated the top number I know thats it now how to access it. thats listed as inactive under my ip scanner. Ok whats the next step.lol Thank you so much for any help as I am a disabled veteran. my pc is a custom built Intel I7 4th generation computer running windows 10. this one is Dead 192.168.1.99 192.168.1.99 Paragon Technologies Inc.
Ok 192.168.1.xx 192.168.1.xx Shenzhen Ogemray Technology Co., Ltd. Update after I set it up the old owner had it set to a specific address so when I changed from static to dhcp it went back to the address he had it set at. I checked the unit as it is hooked up to my router and is working great. Ok whats the next step to get my router to tie to my computer. When I changed from static to dhcp it inactivated the 192.168.1.99 and activated the top number I know thats it now how to access it. thats listed as inactive under my ip scanner. Ok whats the next step.lol Thank you so much for any help as I am a disabled veteran. my pc is a custom built Intel I7 4th generation computer running windows 10. this one is Dead 192.168.1.99 192.168.1.99 Paragon Technologies Inc.
I'm pretty upset and frazzled, I received a bitmain antminer s3 for my son and I to work on together as a hobby he is 9, and I recieved it today. I was really excited and thought the installation would be straightforward but no it was anything but that. I had it hooked up to my router and I could not find it after following the intructions so I hooked it up straight to my computer typed in the default ip address and walla there it was I followed the intructions and went into the client using root root then I changed the network settings form static to dhcp that when everything went wrong I hooked it back up to my router and was not able to find it so I hooked it up once again and ran the ip scan to find out what the new ip address was two items came up my router and shenzen something technology. I typed that ip number into my address search bar and nothing came up. I am lost now please help. First I would try just restarting it and have the S3 connected to your router, if truly in DHCP it should find it. Does the S3 fan's seem to be spinning like it is mining when you cannot find it? What PSU are you using (just making sure you are not getting connnection and it is trying to mine and having problems due to PSU I doubt it with S3 but still possible).
When making network changes I would take a screenshot, yes it's overkill but even though I have configured a good amount of miners I still do it. It gives you something to look at just incase your IP change went wrong from wrong selection (lucky I have not needed it ... just like to be prepared).
Ok assuming you have restarted, tried to find and no luck still no matter what log into router to and see connected devices and see if it's there. But take a deep breath as there is a reset button. I am curious on questions I asked before doing one. Just to warn you if you do reset make sure to follow a guide and DO NOT turn off power/lose power during it or you could end up with a S3 controller board that needs re-programed.
I'm pretty upset and frazzled, I received a bitmain antminer s3 for my son and I to work on together as a hobby he is 9, and I recieved it today. I was really excited and thought the installation would be straightforward but no it was anything but that. I had it hooked up to my router and I could not find it after following the intructions so I hooked it up straight to my computer typed in the default ip address and walla there it was I followed the intructions and went into the client using root root then I changed the network settings form static to dhcp that when everything went wrong I hooked it back up to my router and was not able to find it so I hooked it up once again and ran the ip scan to find out what the new ip address was two items came up my router and shenzen something technology. I typed that ip number into my address search bar and nothing came up. I am lost now please help. damn... just can't get to type anything...
I've tried with Termite also, but the typing does't do shit...
The command line that should follow is this:
" athrs26_reg_init_lan"
Does that mean its ethernet drivers (atheros) are corrupted if the line is not launching ?!?
By the way THX d57heinz!
I've tried with Termite also, but the typing does't do shit...
The command line that should follow is this:
" athrs26_reg_init_lan"
Does that mean its ethernet drivers (atheros) are corrupted if the line is not launching ?!?
By the way THX d57heinz!
Is this like Putty? Try pressing 'i' for insert or 'esc' to see if you can type any command after 'esc'.
damn... just can't get to type anything...
I've tried with Termite also, but the typing does't do shit...
The command line that should follow is this:
" athrs26_reg_init_lan"
Does that mean its ethernet drivers (atheros) are corrupted if the line is not launching ?!?
By the way THX d57heinz!
I've tried with Termite also, but the typing does't do shit...
The command line that should follow is this:
" athrs26_reg_init_lan"
Does that mean its ethernet drivers (atheros) are corrupted if the line is not launching ?!?
By the way THX d57heinz!
seems these S3+ minors still have life left in them thanks to the bitcoin price raise, making around $25 a month now.
Sorry im not real familiar with this method.. I think you need to somehow interrupt the connection when its about to output that data you presented.(possibly by pressing control c or esc maybe idk) Ill do some digging for you and see what i can come up with. I found that with a couple quick google searches. I had some brick on me a long time ago.. ended up never getting back to them.> i may pull one out just to see about this procedure for my own knowledge if nothing else. Ill get a usb to cp2102 adapter ordered and see what i can come up with. give me something to work on in my free time next week. Let me know if you discovered anything new in the meantime.
Best Regards
d57heinz
Best Regards
d57heinz
Shit got it !! (I used session instead with host name COM_)
But i'm stuck there... cannot type anything !!!!!
U-Boot 1.1.4 (Apr 11 2013 - 01:45:00)
U-boot for ELink, build by huangfc(QQ:343669866)
Taobao:http://huangfc.taobao.com
model:ELink M150
DRAM: 64 MB
led turning on for 1s...
id read 0x100000ff
flash size 8388608, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
But i'm stuck there... cannot type anything !!!!!
U-Boot 1.1.4 (Apr 11 2013 - 01:45:00)
U-boot for ELink, build by huangfc(QQ:343669866)
Taobao:http://huangfc.taobao.com
model:ELink M150
DRAM: 64 MB
led turning on for 1s...
id read 0x100000ff
flash size 8388608, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
Jump to: