ANTMINER S4 Discussion and Support Thread - page 72.

Nightshiftgirl

member

Activity: 154

Merit: 10

Dogie,
I am online I will send you my team viewer id via PM
thanks for the offer

Barbara

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: Nightshiftgirl on December 07, 2014, 05:35:59 PM

Thanks for your thoughts

Barbara

If you install teamviewer I'll do it for you when you're next on.

suchmoon

legendary

Activity: 3654

Merit: 8909

https://bpip.org

Quote from: Deagle21 on December 07, 2014, 06:38:25 PM

I have a 13 amp 250 volt PC power cord laying around. I image it would be fine for the S4 running from a 120 volt socket?

Barely. Ideally you want 15 amps or better. Also keep in mind that it's the gauge that matters. If it's 14 AWG or better it will be fine.

Deagle21

full member

Activity: 333

Merit: 100

I have a 13 amp 250 volt PC power cord laying around. I image it would be fine for the S4 running from a 120 volt socket?

Nightshiftgirl

member

Activity: 154

Merit: 10

I am double posting this as I really need an answer soon S4 and C1 Support

I am trying to flash a file to a sd card

I downloaded the files tar.gz both for the S4 and the C1

I downloaded Win32Disk imager.

I put the SD cards in my computer, I can view the old files there are 7 of them.

I point Win32Disk imager to the downloaded tar.gz files.

I Point the Device to the SD card and select write.

I warns me and then writes.

I try to view the file on and it says I have to format the disk first. {Okay I know I just viewed the previous image)

I put the card in the miner and it runs high fans for over 5 min and nothing at all happens, the fans do not slow down and the Watt meter does not register any real usage.

This should not be so difficult even for a old person like me.

Thanks for your thoughts

Barbara

Nightshiftgirl

member

Activity: 154

Merit: 10

Dogie,
I did that now the fans just spin on Hi and nothing happens. Just noise let it run over 5 min
Barbara

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: Nightshiftgirl on December 07, 2014, 03:35:53 PM

I am sorry for the dumb question, but I have been looking for how to and can not seem to find it.

First I have a S4 it was way to loud where it was so I decided to under clock it. Not really in it for the money.

I typed in freq 125 and voltage 0630 exactly on the adjustment page.

Without me doing anything it started hashing at the lower rate, and after about 5 Min it started beeping so I turned it off and back on. Now it started the fans run really high and the display showed 127.0.0.1.

So I downloaded the firmware from Bitmain, unzipped it and copied it to the sd card, now it just spins the fan really fast.

I tried to use winimage but it keeps looking for a floppy drive? Huh

Can someone please tell me or point me to a link that details how to do this on a windows 8.1 machine?

Be gentle I am 67 years old and trying a new hobby.

I also have a C1 that needs flashed as it wont work either

Barbara

Don't unzip anything, redownload it. Then use a program called sd card imager to load the image onto the SD card.

Nightshiftgirl

member

Activity: 154

Merit: 10

I am sorry for the dumb question, but I have been looking for how to and can not seem to find it.

First I have a S4 it was way to loud where it was so I decided to under clock it. Not really in it for the money.

I typed in freq 125 and voltage 0630 exactly on the adjustment page.

Without me doing anything it started hashing at the lower rate, and after about 5 Min it started beeping so I turned it off and back on. Now it started the fans run really high and the display showed 127.0.0.1.

So I downloaded the firmware from Bitmain, unzipped it and copied it to the sd card, now it just spins the fan really fast.

I tried to use winimage but it keeps looking for a floppy drive? Huh

Can someone please tell me or point me to a link that details how to do this on a windows 8.1 machine?

Be gentle I am 67 years old and trying a new hobby.

I also have a C1 that needs flashed as it wont work either

Barbara

tfoto

newbie

Activity: 24

Merit: 0

If anyone should be coupons, write to the PM.
Specify any coupons needed. how many pieces. and login bitmen

vegasguy

legendary

Activity: 1610

Merit: 1003

"Yobit pump alert software" Link in my signature!

ok.. very kind , donate to [email protected] . Ill donate my (3) S4's ($400) off and C1 ($50) off, if anyone wants them for free.

Thanks

fullzero

legendary

Activity: 1260

Merit: 1009

vegasguy pm me your bitmaintech id and I will send you the other 12.

faetos

hero member

Activity: 744

Merit: 514

gotta let a coin be a coin

Quote from: vegasguy on December 07, 2014, 12:06:15 AM

Looking to trade or buy S3 coupons. Need 19 of em. I have the following coupons I can trade : (1 coupon for 1 coupon). Ill need to buy the rest from you.

(1)AntMiner C1 Coupon 50 USD off
(3) AntMiner S4 Coupon 400 USD off

These are good until 12-15-14

I need to buy (19) S3 coupons. They sell for $1 a piece on Ebay so if anyone has a lot of 20, I can buy them for $20 in btc. Nobody on Ebay has 20, thats why I am asking here.

Does anyone know if bitmain will accept 20 coupons for 20 S3+?

Vegas

I've got 8 and will give those to you for free. I need your bitmain id to send them.

vegasguy

legendary

Activity: 1610

Merit: 1003

"Yobit pump alert software" Link in my signature!

Looking to trade or buy S3 coupons. Need 19 of em. I have the following coupons I can trade : (1 coupon for 1 coupon). Ill need to buy the rest from you.

(1)AntMiner C1 Coupon 50 USD off
(3) AntMiner S4 Coupon 400 USD off

These are good until 12-15-14

I need to buy (19) S3 coupons. They sell for $1 a piece on Ebay so if anyone has a lot of 20, I can buy them for $20 in btc. Nobody on Ebay has 20, thats why I am asking here.

Does anyone know if bitmain will accept 20 coupons for 20 S3+?

Vegas

abracadabra

hero member

Activity: 956

Merit: 1001

Quote from: dmwardjr on December 04, 2014, 01:38:36 AM

From October to May it averages out to .068 cents per kWH and from June to September it averages out to .0787 cents per kWH in Alabama: http://www.alabamapower.com/residential/pricing-rates/standard-rate-family-dwelling.asp

Did you apply for 800A service from your utility? 96 S4s will require a bit over 600A @ 220V

dkaufman

member

Activity: 84

Merit: 10

Quote from: sEpuLchEr on December 05, 2014, 04:36:37 AM

Quote from: dkaufman on December 05, 2014, 03:56:51 AM

Does anyone have an extra $50-off coupon for an S3?

Bitmain gave me three but I wanna add four more...

My bitmain User ID is dkaufman (...just like my BitcoinTalk ID. Hmmmm... coincidence?)

Thanks!

-dave

OTW

Done!

Thanks, sEpuLchEr!

You rock!

-dave

faetos

hero member

Activity: 744

Merit: 514

gotta let a coin be a coin

Quote from: Tupsu on December 04, 2014, 11:02:24 PM

Quote from: faetos on December 04, 2014, 10:49:15 PM

When you all sell your used mining equipment what has been the most reliable place to sell it?

ebay.de and Estonian local sales websites such as osta.ee

thanks, Tupsu

Bitkoinzz

full member

Activity: 218

Merit: 100

For everyone who was having issues in getting their S4's to show full speed in their pools....

You do need to set your minimum difficulty to 2048 for each worker however I tried BTCGuild and they are paying about HALF of what Slush's pool is. I will make .0345 a day each in Slush's pool. BTCGuild was .016. S4's set at 225mh 0725 volts doing about 2200 gh. No good. And that was at 16 shifts a day. Nooooo bueno.

mining.bitcoin.cz is the way to go.

If anyone is getting bigger pool payouys in a different pool please post it.

EDIT P.S. does anyone have any info on the upcoming S5?

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: sEpuLchEr on December 05, 2014, 04:36:37 AM

Quote from: dkaufman on December 05, 2014, 03:56:51 AM

Does anyone have an extra $50-off coupon for an S3?

Bitmain gave me three but I wanna add four more...

My bitmain User ID is dkaufman (...just like my BitcoinTalk ID. Hmmmm... coincidence?)

Thanks!

-dave

OTW

Done!

If you need any more just email [email protected]. Its hard for us to add them AFTER your order so please be patient and wait to apply them before your order.

sEpuLchEr

sr. member

Activity: 248

Merit: 250

Are we there yet?

Quote from: dkaufman on December 05, 2014, 03:56:51 AM

Does anyone have an extra $50-off coupon for an S3?

Bitmain gave me three but I wanna add four more...

My bitmain User ID is dkaufman (...just like my BitcoinTalk ID. Hmmmm... coincidence?)

Thanks!

-dave

OTW

Done!

dkaufman

member

Activity: 84

Merit: 10

Does anyone have an extra $50-off coupon for an S3?

Bitmain gave me three but I wanna add four more...

My bitmain User ID is dkaufman (...just like my BitcoinTalk ID. Hmmmm... coincidence?)

Thanks!

-dave

Topic: ANTMINER S4 Discussion and Support Thread - page 72. (Read 301481 times)