ANTMINER U3 Discussion and Support Thread - page 46.

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: Kx2000 on February 13, 2015, 09:18:38 AM

I someone can help me to get my U3 functionnal on minepeon

I'm newbie on Linux... Cgminer don't reconize the U3

Thanks for help.

Which version of cgminer are you running, 'official' or Bitmain's?

Kx2000

newbie

Activity: 13

Merit: 0

I someone can help me to get my U3 functionnal on minepeon

I'm newbie on Linux... Cgminer don't reconize the U3

Thanks for help.

ID4

newbie

Activity: 6

Merit: 0

My Laptop has 3 USB Ports.

No other Miner connected!!!
I have tried other Computers!!! ( Driver shows up, cgminer: no devices detected )
( i'm wiriting this just because you think i'm stupid and do all wrong )

Even on Ports where the U3 never was connected zdiag 2.1.1 shows:

cp2102 USB to ....

Driver WinUSB (v6.1.7600.16385) --> Driver WinUSB (v6.1.7600.16385)

Reinstall Driver

I HAVE REINSTALLED THE DRIVER!!!

cgminer 4.9.1 --benchmark still No devices detected!

EAT THIS! Wink

richardamullens

newbie

Activity: 51

Merit: 0

Are (some of) these problems peculiar to Windows ?
Would people be better off purchasing the new Raspberry Pi 2 (quadcore Arm 7 + 1GB memory)

Visvas

newbie

Activity: 32

Merit: 0

Quote from: ID4 on February 11, 2015, 10:30:47 PM

WTF?
I have reinstalled the WinUSB Driver V6.1.7600.16385 with Zdiag Version 2.1.1 Build 674!
Months before this i have installed and used WinUSB Driver from Zdiag Version 2.1.0 for my
Antminer U2 and the Rockminer RBoxes!!!
The Antminer U2 and the Rockminer are using the WinUSB Driver V6.1.7600.16385 without problems!!!
If i plug in the USB from Antminer U3 my Windows 7 64bit will install the same WinUSB Driver as for my Antminer U2 or Rockminer Rboxes.

Antminer U2 / Rockminer R-Box and Antminer U3 are using the same WinUSB Driver.

DO NOT TELL ME ANOTHER TIME I HAVE TO INSTALL WinUSB Driver!!!
The Driver is installed and working fine with my other Miners!

Cgminer 0.4.9.1 don't recognize the Antminer U3.

Roll Eyes

No need to get worked up about this, it's actually a quite common error and myself i experience several times that i need to reinstall the winusb driver with zadig for the exact same u3 on the same port as i first installed it. Just check it at least...
cgminer have had native support working from 4.8, with a few new parameters specifically for it in 4.9. That part been working fine here both with the precompiled windows bin and my own compiling on ubuntu.

Phosphorous

hero member

Activity: 556

Merit: 500

Quote from: ID4 on February 11, 2015, 10:30:47 PM

WTF?
I have reinstalled the WinUSB Driver V6.1.7600.16385 with Zdiag Version 2.1.1 Build 674!
Months before this i have installed and used WinUSB Driver from Zdiag Version 2.1.0 for my
Antminer U2 and the Rockminer RBoxes!!!
The Antminer U2 and the Rockminer are using the WinUSB Driver V6.1.7600.16385 without problems!!!
If i plug in the USB from Antminer U3 my Windows 7 64bit will install the same WinUSB Driver as for my Antminer U2 or Rockminer Rboxes.

Antminer U2 / Rockminer R-Box and Antminer U3 are using the same WinUSB Driver.

DO NOT TELL ME ANOTHER TIME I HAVE TO INSTALL WinUSB Driver!!!
The Driver is installed and working fine with my other Miners!

Cgminer 0.4.9.1 don't recognize the Antminer U3.

Roll Eyes

Are you sure the WinUSB driver is assigned to the U3 device? Just because the WinUSB driver is installed and working for other devices does not mean that you have changed the driver for the U3. In Zadig, look at all of the CP2102 entries and verify the driver that each one is using.

ID4

newbie

Activity: 6

Merit: 0

WTF?
I have reinstalled the WinUSB Driver V6.1.7600.16385 with Zdiag Version 2.1.1 Build 674!
Months before this i have installed and used WinUSB Driver from Zdiag Version 2.1.0 for my
Antminer U2 and the Rockminer RBoxes!!!
The Antminer U2 and the Rockminer are using the WinUSB Driver V6.1.7600.16385 without problems!!!
If i plug in the USB from Antminer U3 my Windows 7 64bit will install the same WinUSB Driver as for my Antminer U2 or Rockminer Rboxes.

Antminer U2 / Rockminer R-Box and Antminer U3 are using the same WinUSB Driver.

DO NOT TELL ME ANOTHER TIME I HAVE TO INSTALL WinUSB Driver!!!
The Driver is installed and working fine with my other Miners!

Cgminer 0.4.9.1 don't recognize the Antminer U3.

Roll Eyes

Phosphorous

hero member

Activity: 556

Merit: 500

Quote from: ID4 on February 11, 2015, 04:57:43 PM

Quote from: dogie on February 06, 2015, 04:13:03 PM

Quote from: ID4 on February 05, 2015, 10:51:15 PM

Hi!

I have received my U3 yesterday.

Unfortunatly the U3 will not work.

1. Plug in Power
2. Plug in USB
3. Device is recognized and installs CP2102 Driver

Starting cgminer --benchmark ( Ver. 0.4.9.1 ) No Device found
Starting cgminer --benchmark ( Ver. 0.4.6.1 from bitmain HP) No Device found

Replacing U3 with a R-Box or New RBox and there are no problems, cgminer is hashing

Is my Bitmain U3 DOA?

Follow the instructions /vp1Yad]here, you haven't Zadig'ed yet.

I think nobody has read my post carefully.

Rockminer R-Box / New-RBox and a Antminer U2 are using the same driver and are running without problems.

1. Power up Antminer U3
2. Connecting USB to Antminer U3
3. CP2102 USB to .... show up in Device-Manager
4. starting cgminer 0.4.9.1 with --benchmark parameter
5. No Device detected / Waiting for USB hotplug device or press q to quit / Pool 0 not .....
6. waiting 3 minutes > nothing
7. Plug Rockminer New R-Box into USB and after a few seconds the New R-Box will beginn to hash

Antminer U3 DOA or what is my mistake?

THX!

I don't think you read our responses carefully. Step 3.5: Use Zadig to change USB driver to WinUSB driver.

ID4

newbie

Activity: 6

Merit: 0

Quote from: dogie on February 06, 2015, 04:13:03 PM

Quote from: ID4 on February 05, 2015, 10:51:15 PM

Hi!

I have received my U3 yesterday.

Unfortunatly the U3 will not work.

1. Plug in Power
2. Plug in USB
3. Device is recognized and installs CP2102 Driver

Starting cgminer --benchmark ( Ver. 0.4.9.1 ) No Device found
Starting cgminer --benchmark ( Ver. 0.4.6.1 from bitmain HP) No Device found

Replacing U3 with a R-Box or New RBox and there are no problems, cgminer is hashing

Is my Bitmain U3 DOA?

Follow the instructions /vp1Yad]here, you haven't Zadig'ed yet.

I think nobody has read my post carefully.

Rockminer R-Box / New-RBox and a Antminer U2 are using the same driver and are running without problems.

1. Power up Antminer U3
2. Connecting USB to Antminer U3
3. CP2102 USB to .... show up in Device-Manager
4. starting cgminer 0.4.9.1 with --benchmark parameter
5. No Device detected / Waiting for USB hotplug device or press q to quit / Pool 0 not .....
6. waiting 3 minutes > nothing
7. Plug Rockminer New R-Box into USB and after a few seconds the New R-Box will beginn to hash

Antminer U3 DOA or what is my mistake?

THX!

Visvas

newbie

Activity: 32

Merit: 0

Thanks, testing one at a time alone now, believe it's one of them causing the most issues, so might send that back.

But just to be clear, i love the concept of these little units you guys made, how very well they fit with the need of a hobbyist miner. Silent, small and wife friendly:)
High hopes of the next generation of them, hoping we can get some experience shared here from someone testing the new ones.

MyRig

donator

Activity: 792

Merit: 510

[email protected]

If you think it is very unstable, please send it back to

Bitmain Warranty
3700 Quebec Street
Unit 100-239
Denver, Colorado 80207
USA

Tel: 844-248-6246 Option2 (USA Country Code is 1)

Please use a tracking number and include a printed paper with your shipping information and a telephone number and where you purchased it from

Thanks and sorry for the trouble....

Quote from: Visvas on February 09, 2015, 02:42:59 AM

Quote from: MyRig on February 08, 2015, 03:10:42 AM

@Visvas,

what version of U3 are you using? the new cage looking version or the rice cooker version?

the rice cooker version. Rough metal with holes.

Visvas

newbie

Activity: 32

Merit: 0

Quote from: MyRig on February 08, 2015, 03:10:42 AM

@Visvas,

what version of U3 are you using? the new cage looking version or the rice cooker version?

the rice cooker version. Rough metal with holes.

MyRig

donator

Activity: 792

Merit: 510

[email protected]

@Visvas,

what version of U3 are you using? the new cage looking version or the rice cooker version?

Visvas

newbie

Activity: 32

Merit: 0

Quick status around our "clean it up" testing etc.

Been running the two (out of 3) semi working u3s for a while. Both cleaned up neatly, applied non conductive paste, Noctua NT-H1. One of them has a new psu, Chieftec AC Power Adapter CDP-090ITX 90W.

Unable to have any consistent data on the psu effect on performance here.
Units are very much ureliable, needs to be reset at least once a day. Clean up doesnt seem to have affected reliability.
Getting better performance with cgminer from bitmain, but the latest version with changed parameters compared to the last 2014 version seems to be slower. Hopefully more stable...
Both units running open, no cover, and with extra cooling surfaces attached to the heatsink.

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: ID4 on February 05, 2015, 10:51:15 PM

Hi!

I have received my U3 yesterday.

Unfortunatly the U3 will not work.

1. Plug in Power
2. Plug in USB
3. Device is recognized and installs CP2102 Driver

Starting cgminer --benchmark ( Ver. 0.4.9.1 ) No Device found
Starting cgminer --benchmark ( Ver. 0.4.6.1 from bitmain HP) No Device found

Replacing U3 with a R-Box or New RBox and there are no problems, cgminer is hashing

Is my Bitmain U3 DOA?

Follow the instructions here, you haven't Zadig'ed yet.

jackbox

legendary

Activity: 1246

Merit: 1024

Quote from: Phosphorous on February 06, 2015, 12:53:13 AM

Don't expect much reliability from the U3...

LOL! What a POS device this U3 must be. Cry

Phosphorous

hero member

Activity: 556

Merit: 500

Quote from: ID4 on February 05, 2015, 10:51:15 PM

Hi!

I have received my U3 yesterday.

Unfortunatly the U3 will not work.

1. Plug in Power
2. Plug in USB
3. Device is recognized and installs CP2102 Driver

Starting cgminer --benchmark ( Ver. 0.4.9.1 ) No Device found
Starting cgminer --benchmark ( Ver. 0.4.6.1 from bitmain HP) No Device found

Replacing U3 with a R-Box or New RBox and there are no problems, cgminer is hashing

Is my Bitmain U3 DOA?

Use Zadig to replace the driver with WinUSB driver. Don't expect much reliability from the U3, but you should at least be able to get it to work for a little while.

ID4

newbie

Activity: 6

Merit: 0

Hi!

I have received my U3 yesterday.

Unfortunatly the U3 will not work.

1. Plug in Power
2. Plug in USB
3. Device is recognized and installs CP2102 Driver

Starting cgminer --benchmark ( Ver. 0.4.9.1 ) No Device found
Starting cgminer --benchmark ( Ver. 0.4.6.1 from bitmain HP) No Device found

Replacing U3 with a R-Box or New RBox and there are no problems, cgminer is hashing

Is my Bitmain U3 DOA?

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: ?? on ??

I think its worth paying a little more and getting a used RM850.

It'd be a hell of a lot more, surely?

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: Helfred on February 04, 2015, 06:17:19 AM

Somebody remarked that in this thread are recommendations ot Atx-type psu to replace the U3 one.
Can somebody repeat that ?

Couldn't just find it on the 30 pages ))))))

Because the U3s requirements are essentially nothing, you'll want to look at a power supply you may have a use for in the future (other miners), as an investment. It would be wasteful to get something small and tiny for the U3 and later find out you can't do anything with it. The most recommended single PSU for mining is the Corsair CX750M.

Topic: ANTMINER U3 Discussion and Support Thread - page 46. (Read 149493 times)