Pages:
Author

Topic: Anyone else having issues with their Antminer A3? - page 6. (Read 2293 times)

member
Activity: 140
Merit: 17
I would stop mining on sia pool, seems they are doing something to mess up A3's
It wasn't siamining, it was the whole network (only A3s though). Nobody knows why yet.
hero member
Activity: 1118
Merit: 541
I received my A3 this afternoon and having been having some problems. When I first set it up, everything was working flawlessly. Hashing at 833GHs on Siamining, no HW errors, everything smooth. About 2 hours later I checked again and saw my hashrate dropped in half with a bunch of X's on one of the hashboards. Since then I've only been able to reach 500-600 GHs, and am getting HW errors on different boards whenever I refresh. Anyone else having issues? I would normally try reflashing the firmware but it's not available on Bitmain's support page.

Ya, sia coin developers were testing a soft fork to render the A3 useless. The total hashrate for the whole network dropped by almost half around 1:30PM EST. Hashrate dropped for all A3 on every pool simultaneously.



newbie
Activity: 12
Merit: 0
i did access the router settings page and looked at all of the devices that are connected and its not listed.

when i unplug the ethernet cable from the A3 it makes so fan adjustments and when i reconnect it - seems to "power" up again

so it seems like there is a signal/connection with the ethernet cable
hero member
Activity: 895
Merit: 504
can someone help me find my ip address for the A3?

using apw3++ on 110v
connected on ethernet cable with orange light on and green light quickly blinking.
red "fault" light is off and green "normal" light is steady slow blinking
the only other light is a red light on top at the control board

i am in california and have comcast cable
i accessed my router admin page and searched the connected devices and it does not appear
i have pushed the "ip report" button numerous times
i have powered the unit on and off several times including my router
i have pushed the "reset" several times for over 10 seconds and yes i felt the button inside click

any advice?

Access your router's settings page amd find attached devices. If the A3 is connected, it should show up as ANTMINER.
newbie
Activity: 12
Merit: 0
can someone help me find my ip address for the A3?

using apw3++ on 110v
connected on ethernet cable with orange light on and green light quickly blinking.
red "fault" light is off and green "normal" light is steady slow blinking
the only other light is a red light on top at the control board

i am in california and have comcast cable
i accessed my router admin page and searched the connected devices and it does not appear
i have pushed the "ip report" button numerous times
i have powered the unit on and off several times including my router
i have pushed the "reset" several times for over 10 seconds and yes i felt the button inside click

any advice?
full member
Activity: 1148
Merit: 132
nm looks like a false alarm maybe ddos on the pool
full member
Activity: 1148
Merit: 132
Where do you recommend mining then?
suprnova is a fair pool
member
Activity: 112
Merit: 17
Where do you recommend mining then?
full member
Activity: 1148
Merit: 132
I would stop mining on sia pool, seems they are doing something to mess up A3's
member
Activity: 112
Merit: 17
I received my A3 this afternoon and having been having some problems. When I first set it up, everything was working flawlessly. Hashing at 833GHs on Siamining, no HW errors, everything smooth. About 2 hours later I checked again and saw my hashrate dropped in half with a bunch of X's on one of the hashboards. Since then I've only been able to reach 500-600 GHs, and am getting HW errors on different boards whenever I refresh. Anyone else having issues? I would normally try reflashing the firmware but it's not available on Bitmain's support page.
Pages:
Jump to: