Topic: Avalon ASIC users thread - page 158. (Read 438516 times)
can anyone link me to a site where i can get fan upgrades in the EU?
I just think the blue fan is a bit shit........all three of my batch one blue fans could run a bit better
In the beginning at max PWM speed i thought that blue fan is sucking air from the unit instead of blowing cold air from outside. I put a lighter near by two PWM fans and i clearly can see the light going against the avalon. When lighter was close to blue one it was the opposite and lite was off..That is why i thought shit the fan is sucking.. And this may be due to air turbulence inside and that can make fan stop also as reported. I have to try same with smoke
Something is wrong with blue fan. I will change it these days
I just think the blue fan is a bit shit........all three of my batch one blue fans could run a bit better
So I thought I'd make it easy for everyone to try the latest cgminer 3.3.0 and overclock settings all rolled into one, so here is a firmware with the overclock settings settable from the web interface:
http://ck.kolivas.org/apps/cgminer/avalon/20130624/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin
Note that I have donation settings in the configuration so if you do not use your own config settings, it will start mining for me until you change them.
Usual warnings apply with aggressive overclocking: do so at your own risk!
Enjoy
http://ck.kolivas.org/apps/cgminer/avalon/20130624/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin
Note that I have donation settings in the configuration so if you do not use your own config settings, it will start mining for me until you change them.
Usual warnings apply with aggressive overclocking: do so at your own risk!
Enjoy
tried running the modded firmware on my btach 1's just to see if running the fanz on MAX(not above 300mhz) would make the units cooler/more efficient...... the fan with the blue light just jams when i try this though, it obviously has issues with going at max speed
So I thought I'd make it easy for everyone to try the latest cgminer 3.3.0 and overclock settings all rolled into one, so here is a firmware with the overclock settings settable from the web interface:
http://ck.kolivas.org/apps/cgminer/avalon/20130624/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin
Note that I have donation settings in the configuration so if you do not use your own config settings, it will start mining for me until you change them.
Usual warnings apply with aggressive overclocking: do so at your own risk!
Enjoy
http://ck.kolivas.org/apps/cgminer/avalon/20130624/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin
Note that I have donation settings in the configuration so if you do not use your own config settings, it will start mining for me until you change them.
Usual warnings apply with aggressive overclocking: do so at your own risk!
Enjoy
tried running the modded firmware on my btach 1's just to see if running the fanz on MAX(not above 300mhz) would make the units cooler/more efficient...... the fan with the blue light just jams when i try this though, it obviously has issues with going at max speed
yeah i imagine it is to do with the stock PSU, I am away to order 3 750w gold corsair's today, so maybe by the end of the week i will have them all upgraded.
going to get some fan upgrades also....
going to get some fan upgrades also....
So I thought I'd make it easy for everyone to try the latest cgminer 3.3.0 and overclock settings all rolled into one, so here is a firmware with the overclock settings settable from the web interface:
http://ck.kolivas.org/apps/cgminer/avalon/20130624/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin
Note that I have donation settings in the configuration so if you do not use your own config settings, it will start mining for me until you change them.
Usual warnings apply with aggressive overclocking: do so at your own risk!
Enjoy
http://ck.kolivas.org/apps/cgminer/avalon/20130624/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin
Note that I have donation settings in the configuration so if you do not use your own config settings, it will start mining for me until you change them.
Usual warnings apply with aggressive overclocking: do so at your own risk!
Enjoy
tried running the modded firmware on my btach 1's just to see if running the fanz on MAX(not above 300mhz) would make the units cooler/more efficient...... the fan with the blue light just jams when i try this though, it obviously has issues with going at max speed
So I thought I'd make it easy for everyone to try the latest cgminer 3.3.0 and overclock settings all rolled into one, so here is a firmware with the overclock settings settable from the web interface:
http://ck.kolivas.org/apps/cgminer/avalon/20130624/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin
Note that I have donation settings in the configuration so if you do not use your own config settings, it will start mining for me until you change them.
Usual warnings apply with aggressive overclocking: do so at your own risk!
Enjoy
http://ck.kolivas.org/apps/cgminer/avalon/20130624/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin
Note that I have donation settings in the configuration so if you do not use your own config settings, it will start mining for me until you change them.
Usual warnings apply with aggressive overclocking: do so at your own risk!
Enjoy
tried running the modded firmware on my btach 1's just to see if running the fanz on MAX(not above 300mhz) would make the units cooler/more efficient...... the fan with the blue light just jams when i try this though, it obviously has issues with going at max speed
I like the creativity expressed in the naming of speed choices.
Please add 450 MHz as Ludicrous speed
as DEATH RACE
I like the creativity expressed in the naming of speed choices.
Please add 450 MHz as Ludicrous speed
Con,
What about Avalon cutoff temp? Will you do it?
Maybe, but what should it be? 80? 90? Should it restart when it gets cooler? Should it be on by default? Should it be user configurable? Will the device respond to a request when it gets that hot and the fpga stuffs up anyway? Does it have any internal throttling of its own?What about Avalon cutoff temp? Will you do it?
1. What should it be? The best option will be to be configurable - --avalon-cutoff=60 degress
2. when temp is > 60 just to put it in idle with fans set to max. Let fans keep max state when unit is idle due to cutoff condition
3. What to do when it gets cooler - I think it shall stay in idle because there were problem with heat and that problem needs interaction - as i said air condition malfunction for instance. If you want to make everyone happy =avalon-cutoff-autoresart=0/1 and avalon-cutoff-autorestart-temp=40 (cooler to 40)
it is getting complicated so in the beginning i suggest it stay OFF forever because of the above arguments.
10X
Con,
What about Avalon cutoff temp? Will you do it?
Maybe, but what should it be? 80? 90? Should it restart when it gets cooler? Should it be on by default? Should it be user configurable? Will the device respond to a request when it gets that hot and the fpga stuffs up anyway? Does it have any internal throttling of its own?What about Avalon cutoff temp? Will you do it?
Those are some great questions
Con,
What about Avalon cutoff temp? Will you do it?
Maybe, but what should it be? 80? 90? Should it restart when it gets cooler? Should it be on by default? Should it be user configurable? Will the device respond to a request when it gets that hot and the fpga stuffs up anyway? Does it have any internal throttling of its own? What about Avalon cutoff temp? Will you do it?
Total HW errors doesn't count, only the overall hashrate since only useful hashrate is counted in the current cgminer (note the old cgminer pre 3.2 counted errors as hashrate).
I like the creativity expressed in the naming of speed choices.
Total HW errors doesn't count, only the overall hashrate since only useful hashrate is counted in the current cgminer (note the old cgminer pre 3.2 counted errors as hashrate).
But if we get HW error isnt that meaning that we stressing the machine or something?
edit: trust the developer, back to 3.3 @ 350 for 24 hours now
Con,
What about Avalon cutoff temp? Will you do it?
What about Avalon cutoff temp? Will you do it?
Total HW errors doesn't count, only the overall hashrate since only useful hashrate is counted in the current cgminer (note the old cgminer pre 3.2 counted errors as hashrate).
I miss the 34:345 option on this latest release. For me it means less HW errors than 350.
Switched back to strombom killing noise
Before I tried start cgminer manually but I could not make it work -- dumb?
Switched back to strombom killing noise
Before I tried start cgminer manually but I could not make it work -- dumb?
I was able to get my avalon connected through the ethernet port on ip 192.168.1.30. After mining for a few a few hours it disconnected and ever since I can't get the the config page. I used to be able to go 192.168.1.3 to acess it. I even tried hooking up the ethernet cord to the laptop and tried 192.168.0.100. Not sure what to try now.
what does HW actually mean?
my guess would be HardWare (error)
Jump to: