Topic: [Awesome Miner] - Powerful Windows GUI to manage and monitor up to 200000 miners - page 262. (Read 703148 times)

@darkneorus dumb question maybe sorry , how do I add them manually and also add them to profit switching or should i wait, it seems the the equihash192 and btg will never be supported , is there a turotiral on how to add pools
manually and also have them work for profit switching and benchmarking ?

because they are not included in default Online Services list yet, but you can add them manually.

not same with sonoa and equihash192, predefined pools do not support them.

@patrike you can consider adding NLPool, Phi-Phi-Pool and Starpool as predefined Yiimp-type pools in place of Zergpool, which is gone now. they all support autoexchange to BTC wallet.

SO what do we do with the error : no pool avaiable for benchmark ?

I get that for like 9 algos including the new one X22i , sonaa

and all the equihash forks

How do I fix this ? , I know blockmasters has x22i for sure why does it not allow benchmark , same with the equihash 192 etc

Thanks, that's great.

Use T-rex 0.7.2 It is 40% more hash (if it is in X22i)

PLS help me

I'm running all my rigs as Managed Profit Miners.  Most of my rigs contain identical GPUs, but I do have a few that are mixed, and I'm having a hard time getting different clock profiles to work consistently with them

I have my Profit Profiles and Groups already setup, and they are as follows:

Profit Profiles

GTX 1050Ti
GTX 1060 3GB
GTX 1070
GTX 1070Ti
GTX 1080
GTX 1080Ti

Profit Profile Groups (these are my mixed rigs other than one that is a mix of air and water 1080Tis discussed below)

1x 1050Ti 1x 1070Ti
2x 1070 x1 1080Ti
1x 1070 1x 1080

For Profit Profiles, I figured it would not be necessary to distinguish between Air and Water Cooled GPUs.  Agreed?

For GPU Clocking Profiles on the other hand, I have created different profiles for Air vs. Water cooled GPUs since they require different settings.  So I have the following:

GTX 1050Ti ETH
GTX 1050Ti Standard
GTX 1060 3GB ETH
GTX 1060 3GB Standard
GTX 1070 ETH
GTX 1070 Standard
GTX 1070 Hybrid ETH
GTX 1070 Hybrid Standard
GTX 1070Ti ETH
GTX 1070Ti Standard
GXT 1080 Hybrid ETH
GTX 1080 Hybrid Standard
GTX 1080Ti ETH
GTX 1080Ti Standard
GTX 1080Ti Hybrid ETH
GTX 1080Ti Hybrid Standard

So I have this one rig with a mix of 1080Ti's that are air cooled and one that is a hybrid.  The GPUs are as follows according to AM:

GPU0 EVGA 1080Ti SC2
GPU1 EVGA 1080Ti SC2
GPU2 EVGA 1080Ti SC2
GPU3 EVGA 1080Ti FTW3 Hybrid
GPU4 EVGA 1080Ti SC2
GPU5 EVGA 1080Ti SC2
GPU6 EVGA 1080Ti SC2

I created a Clocking profile group with 6x 1080Ti Standard profiles and 1x 1080Ti Hybrid Standard.  I arranged the GPUs in the profile to match what is shown in the table above by simply entering 0 - 6 for each GPU.  But apparently I'm doing something wrong since all 7 GPUs share the same clock and power settings and after a short while the miner software is restarted by AM since the FTW3 hybrid keeps falling over because the clocks are too high given the much factory OC of the FTW3 card compared to the SC2's.

When I look at this mining rig in the GPU tab, I can clearly see that the clock on the FTW3 is about 80 MHz higher than the other 6 and it also uses about 40 more Watts.  When I click GPU settings/settings via Awesome Miner and MSI Afterburner... I can confirm that all 7 GPUs share the exact same power and clock settings, which is why the FTW3 runs higher than the rest.  When I click the Profile drop down, the Clocking Profile Group I created is not in the list to choose from.  So how do I associate a Clocking profile group to a particular miner?

Do I have to create a Profit Profile specifically to this mining rig instead of using the regular GXT 1080Ti Profit Profile that I use for all my 1080Ti Air cooled only rigs?

That appears to be the only way I can then select this "custom" 1080Ti Profit Profile, from within which I can then select the Clocking Profile Group I created for individual algos.

EDIT: So I went ahead and created a Profit Profile called GTX 1080Ti Mix and within it, I selected my Clocking profile group with 6x 1080Ti and 1x 1080Ti hybrid.  I then went to this miner and changed the miner properties to point to the new Profit profile I created.  I restarted the miner, but it is still showing all 7 GPUs at 80% and +120 Core.

EDIT2:  I changed to match on GPU Name instead of ID.  Still didn't work.  Here are some pic of my config:

https://ibb.co/jo0hYA

https://ibb.co/mLh1RV

https://ibb.co/iUQufq

https://ibb.co/nJyrRV

https://ibb.co/igBNYA

Note that in the last screenshot above, where I'm showing the "Settings via Awesome Miner and MSI Afterburner", all that is showing GPU 0:, GPU 1:, etc.  The actual name you can see in the window behind, do not carry through to the Afterburner window.  Could that be the issue?  If so, how do I get the GPU names I assigned to show up there?

Thanks!

Making that URL available works well for me.  Thanks!

As for a better way, perhaps under Managed Software Properties, have download URL drop down where one could choose the version, based on what's available at s3.amazonaws.com/awesomeminer-download/?

That's probably a lot of work and maybe there isn't really that large a need for it?  I'm good with just having additional URL available so that I can manually enter under Customer Download URL.

As a workaround you can catch this with "Detect device count, less than or equals: 7". Most time this works, but not when the miner hangs in a damn loop and restarts unlimit time (T-Rex for example always tries to start with the full 8 cards, shows an error and then restart).

hey patrike.
many miners report 0 C temperature for GPUs which stopped responding for some reason (became "lost").



I've tried to create a rule that could take care of these cases (perform actions like restart the miner/reboot the rig/etc) without success.
the trigger "temp less than 1 C" doesn't work in this case, and for some reason '0 C' temp is not accepted in this trigger.

any solutions?

It is required already 5.7.5, with new T-rex ....))))

Try T-rex 0.72. Now with x22i
+30%1060 +40%1070ti +50%1080
Tested

https://i.imgur.com/zY6Yc7t.jpg

zjazz for X22i becomes very unstable, several of my machines are constantly falling out of the pool and entering again. Do you need cuda 10 for this miner?

+1

zjazz_cuda

erorrs:

PLS fix

T-Rex 0.7.1

Added algos: sha256t, timetravel
Replace "--exit-on-fail-shares" parameter with "--reconnect-on-fail-shares"
New/changed arguments:
    --temperature-start: When a GPU cools down to this temperature the miner starts using it again
    --exit-on-fail-shares: Now replaced with --reconnect-on-fail-shares
    -r (--retries): if set to 0, miner exits immediately upon the first network failure
    --cpu-priority: Set process priority (default: 2) 0 idle, 2 normal to 5 highest

Allow C-style comments in config files (see config_example). Can be used to disable failover pools temporarily etc.
A few cosmetic changes.

API:
Multiple http://localhost:4067/trex page enhancements, it now displays all the info you see in the console, including hashrate/power consumption on the graphs with zoom option. (click on left mouse button and drag) Don't need to use console anymore use your browser instead!
New API handler "config".
Some miner parameters can now be changed and saved on the fly.
Please see the help file for additional details.

Bug fixes:
"bad weak ptr" error
Share rejects were not displayed (Suprnova, Aikapool, possibly some others)
Command line arguments did not always override config file


Linux
CUDA 9.1:
https://mega.nz/#!eRFUDQTR!nemrlPpHrde7oZx4696ROyu8ZY7oB09GD-OEgEnEHNU

CUDA 9.2:
https://mega.nz/#!rId2xS6S!pD4WH5-FugkgwBBtWotDHtXUHOPd7h5WymU-n5NTHbE

CUDA 10.0:
https://mega.nz/#!yddiUYYR!r22YiLKqkM-rKhf-Fd5q71_tfsxG9Cb6Q9-63fjnu90


Windows (x64)
CUDA 9.1:
https://mega.nz/#!KYM0mabT!q5rpfmypFWd6s5rguTxv0m6yMHSGdDe0-rDf7rGuTgQ

CUDA 9.2:
https://mega.nz/#!jBFGxYrJ!Rohw-D0eoAiYTbI3c_mXnn1wNrpmfGxHuVbUAwldu_s

CUDA 10.0:
https://mega.nz/#!LMUByaLD!95fBUZyxu1p3CDztToBZskcAVpsORVfDwqPsblawZF0



---------------------------------------------------------------------------



Z-ENEMY VER 1.22a From: Dk & Enemy (z-enemy)

IMPORTANT:
For maximum performance make sure you have latest drivers  (ver. 415+)
http://www.nvidia.com/Download/index.aspx

Cuda 10 x64 ver1. (closed build for  10x0 & 20x0):
https://mega.nz/#!4GJXXKLK!JEflylsVrvl-DG2-WzaGA3_iWs0dnAmAYTcnWkI-RWs

- Minor performance improvements for x16, x17
- Bug fixes and increased stability

Thanks for info..

only https://www.phi-phi-pool.com/  has some new algos (X22i, Sonoa, BCD  )

so maybe it can be added to Awesome miner instead of Zergpool, right Patrike?

the rest looks worse with algos than Zpool..

It looks you are right :/
BTC payout is definitely the best option. Did you contact them, if it would be possible to change this?

Or do anyone know any good Yiimp compatible pool with direct BTC payouts that supports new GPU algos like X22i, Renesis, lbk3, BCD.. 

M.

Awesome Miner version 5.7.4

 GPU mining
  - Display warning on the Summary tab for miners with old nVidia drivers not supporting the latest CUDA version
  - Diagnostics feature improved and includes OS and driver information
 Configuration
  - External Miners can be configured with a Profit profile without having to enable profit switching
 Rules
  - Triggers using the concepts Greater/Less Than or Equals also includes support for Greater/Less Than
 Mining software
  - Added mining software: Zjazz CUDA miner, for X22i
  - WildRig Multi Miner 0.12.5 beta
 Corrections
  - Correction to the default pool configuration of Antminers
  - Correction to revenue calculations for a number of coins based on Equihash variants

True - the miner would need to report it in order for AM to reflect it, after all it is software not hardware. I am going to have to come up with something inline.