Topic: [Awesome Miner] - Powerful Windows GUI to manage and monitor up to 200000 miners - page 97. (Read 703113 times)

Hai @patrike....
Please see mininngpoolhub calculation on online service its completely mess up, on equihash 192.7 algo

Thanks

for two my L3+ asics i cant solve "Cant find signature" error(((

Thanks for sharing the details - I will update this URL in the next release as well.

I will look into this, but please keep in mind that it may take a while for the tuning.

How did you manage to solve the SD card installation problem you had earlier?

Installed you new L3+ firmware (3.8.7.1) and 50% of my asics cant find stable chip config on profiles 500@620w, 505@720w
how long is tuning period? My is endless(
In profile log i see many errors:
[Fri May  1 11:39:28 2020] Fan Err! Disable PIC! Fan1 speed is too low 1320 pwm 40
[Fri May  1 11:39:25 2020] Online..
[Fri May  1 11:38:08 2020] Fan Err! Disable PIC! Fan1 speed is too low 1320 pwm 40
[Fri May  1 11:38:04 2020] Online..
[Fri May  1 11:36:42 2020] Fan Err! Disable PIC! Fan1 speed is too low 1110 pwm 35
[Fri May  1 11:34:42 2020] Online..
[Fri May  1 11:33:31 2020] Fan Err! Disable PIC! Fan1 speed is too low 1170 pwm 37
[Fri May  1 11:31:42 2020] Online..
[Fri May  1 11:30:26 2020] Fan Err! Disable PIC! Fan1 speed is too low 1260 pwm 40
[Fri May  1 11:30:21 2020] Online..
[Fri May  1 11:29:00 2020] Fan Err! Disable PIC! Fan1 speed is too low 1110 pwm 35
[Fri May  1 11:28:58 2020] STAGE2 done..
[Fri May  1 11:28:02 2020] STAGE2 collecting data..
[Fri May  1 11:27:00 2020] Online..
[Fri May  1 11:25:44 2020] Fan Err! Disable PIC! Fan1 speed is too low 1320 pwm 40
[Fri May  1 11:25:40 2020] Online..
[Fri May  1 11:24:24 2020] Fan Err! Disable PIC! Fan1 speed is too low 1260 pwm 40
[Fri May  1 11:24:20 2020] Online..
[Fri May  1 11:23:02 2020] Fan Err! Disable PIC! Fan1 speed is too low 1260 pwm 40
[Fri May  1 11:22:58 2020] Online..


On firmware before tuning was completed in 10-15 min with no such errors in log. Looks like i need downgrade back to 3.8.6

Like @sxemini pointed out, sometimes the Antminers can be a bit sensitive to larger SD cards. The 16 GB card I use happen to works fine, but I'm not sure that's always the case.

If I understood your initial post correctly, you already tried to put the Bitmain firmware on the SD card and tried the flash procedure?

Is this your only Antminer or do you have others to test with as well?

Hi. Sorry, I was reading your initial question about too quick there. For the Mining Profiles, you are correct that it uses web request (port 80) to the Antminer. Right now the web port cannot be modified. I can look into that.

We are also working on another solution for this. We will have a small application you can install on your Antminer that connect the Antminer to our Cloud and uses that as a communication channel to Awesome Miner. This makes it possible for Awesome Miner and an Antminer to be located on separate sites and they would still be able to communicate with each other (API, Web, SSH) without any firewall configuration.

i can reach that the both lights flashing only if i start asic with IP-Reporter button pressed, but this not help too.

yes, i have this content on my SD
16GB ok, checked on Bitmain site.
If i start asic with SD card inserted, normaly i must see that the red and green diodes ON, but in my case this is not a fact(((
only green diode is on and miner continue normal hashing. Looks like my asic ignore reading SD

you have the nand folder and the other files on sd card?



Use a smaller SD Card, 4GB is enough and best for this.

trust me Patrike, i have tried all this steps) I have formated to FAT32 16GB SD card, extracted your files (i saw subfolder "nand"), started asic with SD card inserted. nothing helps.
Maybe i must start asic with SD card and press some buttons during start?
some step by step manual needed...

This ASIC has priveleged access OK
The pool switching work perfect.
Problem is only for switching for predefined mining profiles in Awesome firmware, not a pools. I cant switch between 505 MH, 540 MH, 605 MH and so on. over AwesomeMiner main program.
if i login to asic via web interface, i can without problem change mining profiles.

  no problem

doh that worked. I just tried to set it up this morning, the default one AM provided does not work. I went to the api page and grabbed the one at bottom but that is a direct link. yours is the one further up on the API page - I blame not having my morning coffee yet thank you.

https://verge-blockchain.info/api/balance/[address]

next time read the api documentation:

https://verge-blockchain.info/API

I attempted to add my verge wallet to balances but it doesnt work - by default AM puts the "block explorer API URL" as "https://verge-blockchain.info/ext/getbalance/[address]"


edit:

that url does not work but from the same site i found that https://verge-blockchain.info/address/[address]" does work however when i put that in AM - AM still cannot get my balance.

The profit switcher will use the Cgminer API to make pool priority changes. The web port will not be used. I think your Antminer is running with Restricted API access, where the miner only can be monitored by Awesome Miner but operations like setting pool priorities will not be available.

In order for the profit switcher to work, the miner must be in Privileged API access. As you don't have SSH access on your current firmware version, you will have to install the Awesome Miner firmware for this to work.

The SD card installation method should always work. Can you please verify:

1) The SD card is formatted with FAT32 file system

2) The files you put on the SD card correctly. It is not the same file you install via the web interface that you can put on the SD card. It should look similar to the screenshot you see at the end of this page:
https://support.awesomeminer.com/support/solutions/articles/35000145544-awesome-miner-antminer-firmware-installation

For L3+, you should for example see a few files in the root folder and then have a single sub folder called "nand".

SD card installation is required when running Bitmain firmware from July 2019 and later - as these have the signature validation. Installing via the web interface will give you the signature error message.

Awesome Miner version 7.5.5

 Awesome Miner Antminer firmware
  - New firmware version 3.8.7.1 for Antminer L3+/L3++. After the upgrade, a Mining Profile must be applied for the Antminer to operate at the correct hashrate.
 ASIC mining
  - Temperature display for BraiinsOS BOSminer
 Changes
  - Improved log file rotation
 Mining software
  - Gminer 2.09
  - CpuMiner-Opt 3.12.8.2
  - NbMiner 30.0
 Corrections
  - Managed Profit Switcher correction for a specific scenario where Phoenix Miner is used in combination with thresholds
  - Correction to profit factors calculations for user defined pools in specific scenarios

I have a problem to switch a L3+ asics mining profile over AwesomeMiner->ASIC Tools.
My ASICs is in another location as AwesomeMiner main programm host.( xxx.ddns.net)
I am so understand, that the AwesomeMiner switch mining profiles over web requests. But all my asics is under router port mapping and port 80 is mapped for example over 8101, 8102 and so on.
I cant find in AwesomeMiner program some settings where i can adjust port for extern web requests for ASICs
Or i am wrong? Please help