Topic: BITMAIN Antminer S1 support and OverClocking thread - page 6. (Read 144978 times)

Ok. But I was asking about the original fan came with Ant S1.

the second fan is ac-power from wall, it about 100w.

At full speed (yellow & blue wires detached) how much is the ant s1 fan's energy consumption?

Here is my experience with overclocking:
http://s15.postimg.org/v15jfxgzf/image.jpg
in asic-freq i use this:
        option 'freq_value'    '6002'  #406M
        option 'chip_freq'     '406.25'
        option 'timeout'       '35'

added second fan from russian military device, it sounds loud but gives high air flow.

Yeah that's TCR (Tarif comparison rate) of 14.75p per kw including standing charges

I use the billable rate for my Crypto calculations as i figure i need electric anyway and was paying standing charges before BTC
Billable rate 11.57p

Lots of deals out there, use a comparison site but you will need to sign up for a minimum term
(Mine runs out august this year and I guess will not renew that low)

Just a vacuum and compressed air blower

Take fans off of ends 1st, 2nd vacuum and 3rd compressed air (Dry not wet)

How you are cleaning the heatsink fins of the antminer?
I removed the fan and tried to remove dust but dust is settled deep inside.
If you did any tricky way to clean the fins in depth share it.

Thank you both for your replies!

Solar is something I have looked into, when I move house I want to have some solar panels fitted and then I can take advantage of those.
Also, for the cost of a new PSU i doubt I would save much to be honest, the current PSU that I use is an EVGA 80+ rated 600w and it doesn't get hot to touch.

11p per kw?! I pay 16.64p (thats $0.283 per kw for our American friends). Lucky bugger!!!

I'm going to try and fit my second fan this afternoon, just have to figure out how it will fit on without catching on the screws that hold the blade in. If you have any photos they would be appreciated.

Stephen

Hi
I too am in the UK and was not expecting this hot weather......
I have fitted additional pull fans to mine
http://www.novatech.co.uk/products/components/cooling/fans/100mmplus/co-9050014-ww.html

you need 4pin PWM fans and you'll need to shave the middle plastic ridge off of the 4 pin connector with a stanley knife
I attached the fans to the ants with cable ties (Hey it works)

Mine are clocked @ 375mhz and average 193Ghs
All 3 draw 1190 from the wall 1190 / 3 = 396.6 watts each
The fans even in this weather run @ 1920 with temps avg 43c

I've tried the higher clocks but the noise is "not comfortable" for indoor (terraced house) use.
I've traded GHS for noise reduction - if i lived in field or had a garage then they would be juiced to the max!
I estimate at the current BTC price I'll need to Under-clock them around september time. UK 11p per kw, unless the price keeps increasing and or the difficulty deviates from an estimated 12% per 10 days - easy enough to work out in excel.
I use the recommended corsair 750 psu's - one for each

Wedgy2k

Stephen,  If you can, add a few solar panels and some small plug in type grid tie inverters. I know some places have issues with solar on the roof, but you can still set a panel or two inside a window if you have a South facing window or two.

Solar is cheap and it's literally plug and play now. You just plug in your Positive and Negative DC wires from the panel into the grid tie inverter, and plug the grid tie inverter into any wall socket. Presto, you're done.

The push/pull fan method works great. I did the same thing. I replaced the original cooling fan and used 2 ball bearing 12 volt fans. I mounted one in front and one behind the Ant's cooling fins. My fans are plugged directly into a 4 pin connector from my PSU, so they run a constant speed. The ball bearing fans are extremely quiet. The front fan pushes air in and the back fan pulls hot air out and both work very quietly at 1 speed.

There is a trick I learned by accident that helped me to increase the efficiency of my Antminer.  When my first Ant arrived, I had a elcheapo 875 watt PSU single 12v rail.  It lasted about 3 minutes before it smoked. I grabbed a good name brand supply I had on hand, an Antec 550 watt 80 bronze rating etc, single 12v rail. It worked but the 12volt line voltage dropped to almost an even 11 volts while it was running. It also ran pretty warm. It was borderline hot, but at least it didn't burn up.

So, off I go to the local Best Buy store. They had a sale on Thermaltake 600 watt dual 12v rail supplies. I picked up 2. When I got home, I hooked up each side of the Ant to its own PSU.  The 12 volt line voltage now stays in the high 11's under load, the Ant mines at a higher rate than it did with the single PSU and the 2 PSU's are cool to the touch.

Made me wonder how many GH are being wasted by guys using a small PSU that is barely big enough to power their Ant miners? How much electricity is being wasted because of excess heat from overloading a small PSU, more current draw and most alarming, How many guys are running their Ant at near 11 volts when it's designed to operate at 12? My Ant is not overclocked and it runs consistently in the high 180's and low 190's with an occaisional round or two over 200GH. On the single PSU it ran around 176 GH. Some food for thought anyway. Chris B.

Hi guys some quick advice please!

My S1 is running at 199.18 Ghs at 393Mhz, drawing 426 watts at the wall and temperatures of 46/46.

Firstly, how much power would be saved if I dropped down to 387Mhz? I know i'd probably lose a couple of Ghs but might be worth it if saved enough power as electricity is expensive here?

Secondly, noise! Is there a way to lock the fan setting at 1920 or below? These babies get really noisy and I live in a new house, which in the UK means thin walls so nose is an issue!!
I have brought some 120mm fans to add to the miner in the hope that the push/pull technique might make a difference.

Thank you!!!
Stephen

So I thought I'd post my experiences after having my first S1 up and running for just over 24 hours. I'm used of dealing with various OS's due to my work (deskside support lead for a major cable TV network). I deal with Macs, Windows and even the odd linux box. Which is good since I have mostly PC's at home and 1 mac and and my new Antminer running linux. 

Open it up, get it hooked up to the new PSU I ordered. No issues there. Fire it up. Use my laptop to connect to it via IP after putting it into the same subnet. Reconfigure the IP settings of the miner and put into the proper range for my home network. Then turn it to DHCP and statically assign it in my router. This way as I add new devices, I can't screw up and assign the same IP and it will always get the same IP from the router. 

Someone a couple of pages ago mentioned a stock speed of 160 GH/S. I was getting 140 GH/S after about 10 minutes after configuring my mining pool (eligius). Start messing with OCing and cooling. Add a second fan. One good thing about being a computer tech...always have extra parts around!!  Late last night, finally get it going to 200 GH/S and holding. Go to bed. Wake up today. Still going. Get to work and check. No good. Hash rate has dropped big time. Remote into my home server and SSH into the device and order a reboot. It comes back to a nicely tuned 200 GH/S. Start to have hashing rate issues again in the afternoon but don't have enough time to really mess with it until I get home.

I have the device in my basement, in my storage room beside my server. Ambient temps in the room were around 79F. Get the AC going a bit more and put a fan to blow cooler air from the hallway towards the miner. Room temp now down to 74F. Temps on the miner are 45/43C with them being overclocked 387 freq. I'm getting right around 190 GH/s. It should be a bit higher but it's also drawing about 375 watts according my watt meter. Not sure if this had anything to do with it either way but I plugged it into a 500 watt UPS just in case I was having noise on my outlet. The only other thing plugged into the UPS is my cable modem (got to keep my network up and running!) and I'm still running around 390 watts so I don't think I should be seeing a drain on the battery.

Anyways, I'll have to keep an eye on it's hash rate. I'm still not convinced I have the issues all quite solved but I should know by tomorrow afternoon. High tomorrow is 86F here in Atlanta.

3 overclocked for about 4 months. 1 fell over. The diagnosis was probably a controller issue not cooked hashing chips!! Remaining 2 happily still working.

Any old S1s out there?
I've had mine running for about 4 months at 400 Mhz without any serious problems.
I'm just curious about how long they last. Would like to hear how long you've been running overclocked.

I know someone gave you the parameters but if you did a very very simple google search you
would have easily found the parameter. I know because I searched several times on antminer 387.
SO yea someone figured it out but you obviously haven't figured out how the internet works yet.

You da man now 197.48 GH/s and under 1% HW errors

Any one figure out the Freq and time out settings for the S2 with 64 Chip Chains?